ISO 16145-3:2012

Ships and marine technology — Protective coatings and inspection method — Part 3: Cargo oil tanks of crude oil tankers

This part of ISO 16145 specifies a method of protective coatings and its inspection of cargo oil tanks for crude oil tankers of not less than 5 000 tones deadweight, which are contracted for new building on or after 1 January 2013; or in the absence of a building contract, the keels of which are laid or which are at a similar stage of construction on or after 1 July 2013; or the delivery of which is on or after 1 January 2016. NOTE A crude oil tanker is an oil tanker engaged in the trade of carrying crude oil. This part of ISO 16145 applies to crude oil tankers and crude oil/product carriers as defined in items 1.11.1 or 1.11.4 of the Supplement to the International Oil Pollution Prevention Certificate (Form B).

Navires et technologie maritime — Revêtements de protection et méthode d'inspection — Partie 3: Réservoirs d'huile de chargement de réservoirs de pétrole brut

General Information

• Status: Published
• Publication Date: 30-Sep-2012
• ICS: 47.020.99 - Other standards related to shipbuilding and marine structures
• Technical Committee: ISO/TC 8/SC 8 - Ship design
• Drafting Committee: ISO/TC 8/SC 8 - Ship design
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 06-Dec-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16145-3
First edition
2012-10-01
Ships and marine technology — Protective
coatings and inspection method —
Part 3:
Cargo oil tanks of crude oil tankers
Navires et technologie maritime — Revêtements de protection et
méthode d’inspection —
Partie 3: Réservoirs d’huile de chargement de réservoirs de pétrole brut
Reference number
ISO 16145-3:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 16145-3:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16145-3:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 3
4.1 Symbols . 3
4.2 Abbreviated terms . 3
5 General procedures for coating work . 3
6 Standard for coating work . 4
6.1 Areas considered . 4
6.2 Surface preparation . 6
6.3 Primary surface preparation and shop priming . 7
6.4 Secondary surface preparation . 9
6.5 Coating .10
6.6 Treatment for coating defects .13
7 Inspection .14
7.1 Inspection procedure .14
7.2 Coating inspection .14
7.3 Dry film thickness measurement .16
Annex A (informative) Measurement of the conductivity for abrasives .21
Annex B (informative) Measurement of water soluble salt.23
Annex C (informative) Inspection items and management of inspection .25
Annex D (informative) Assessment of the degree of damage .30
Annex E (informative) Standard for
...