Tool shanks with 7/24 taper for automatic tool changers — Part 1: Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF

ISO 7388-1:2007 specifies the dimensions of tool shanks with a 7/24 taper, of shank forms A, AD, AF, U, UD and UF (with two possible additions for each), for automatic tool changers, used on machines having an automatic gripping system for feeding tools from the magazine to the spindle and vice-versa. These tools are designed with the most important dimensions for use in spindle noses according to ISO 9270.

Queues d'outils à conicité 7/24 pour changement automatique d'outils — Partie 1: Dimensions et désignation des queues de formes A, AD, AF, U, UD et UF

L'ISO 7388-1:2007 spécifie les dimensions des queues d'outils à conicité 7/24 pour changement automatique de formes A, AD, AF, U, UD et UF (avec deux compléments possibles pour chacune) à utiliser sur des machines à dispositifs de préhension automatique pour amener l'outil du magasin à la broche et vice-versa. Ces outils sont conçus avec la plupart des dimensions importantes pour l'utilisation dans les nez de broche conformes à l'ISO 9270.

General Information

Status
Published
Publication Date
29-Jul-2007
Current Stage
9093 - International Standard confirmed
Completion Date
04-Mar-2020
Ref Project

Relations

Buy Standard

Standard
ISO 7388-1:2007 - Tool shanks with 7/24 taper for automatic tool changers
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 7388-1:2007 - Queues d'outils a conicité 7/24 pour changement automatique d'outils
French language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 7388-1
Second edition
2007-08-01
Tool shanks with 7/24 taper for automatic
tool changers —
Part 1:
Dimensions and designation of shanks of
forms A, AD, AF, U, UD and UF
Queues d'outils à conicité 7/24 pour changement automatique
d'outils —
Partie 1: Dimensions et désignation des queues de formes A, AD, AF,
U, UD et UF
Reference number
ISO 7388-1:2007(E)
ISO 2007
---------------------- Page: 1 ----------------------
ISO 7388-1:2007(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2007

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7388-1:2007(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 7388-1 was prepared by Technical Committee ISO/TC 29, Small tools.

This second edition cancels and replaces the first edition (ISO 7388-1:1983), which has been technically

revised. It also incorporates the Addendum ISO 7388-1:1983/Add. 1:1984.

ISO 7388 consists of the following parts, under the general title Tool shanks with 7/24 taper for automatic tool

changers:
⎯ Part 1: Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF
⎯ Part 2: Dimensions and designation of shanks of forms J, JD and JF
⎯ Part 3: Retention knobs for shanks of forms AC, AD, AF, UC, UD, UF, JD and JF
© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 7388-1:2007(E)
Introduction

The aim of ISO 7388 is to integrate existing standards which are most commonly used as an industrial

standard. In addition, the different developments for cooling and data chip have been taken into account.

iv © ISO 2007 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 7388-1:2007(E)
Tool shanks with 7/24 taper for automatic tool changers —
Part 1:
Dimensions and designation of shanks of forms A, AD, AF, U,
UD and UF
1 Scope

This part of ISO 7388 specifies the dimensions of tool shanks with a 7/24 taper, of shank forms A, AD, AF, U,

UD and UF (with two possible additions for each), for automatic tool changers, used on machines having an

automatic gripping system for feeding tools from the magazine to the spindle and vice-versa. These tools are

designed with the most important dimensions for use in spindle noses according to ISO 9270.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

ISO 2768-1, General tolerances — Part 1: Tolerances for linear and angular dimensions without individual

tolerance indications

ISO 2768-2, General tolerances — Part 2: Geometrical tolerances for features without individual tolerance

indications
ISO 8015, Technical drawings — Fundamental tolerancing principle
3 Dime
...

NORME ISO
INTERNATIONALE 7388-1
Deuxième édition
2007-08-01
Queues d'outils à conicité 7/24 pour
changement automatique d'outils —
Partie 1:
Dimensions et désignation des queues de
formes A, AD, AF, U, UD et UF
Tool shanks with 7/24 taper for automatic tool changers —
Part 1: Dimensions and designation of shanks of forms A, AD, AF, U,
UD and UF
Numéro de référence
ISO 7388-1:2007(F)
ISO 2007
---------------------- Page: 1 ----------------------
ISO 7388-1:2007(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2007

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2007 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 7388-1:2007(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 7388-1 a été élaborée par le comité technique ISO/TC 29, Petit outillage.

Cette deuxième édition annule et remplace la première édition (ISO 7388-1:1983), qui a fait l'objet d'une

révision technique. Elle incorpore également l'Addendum ISO 7388-1:1983/Add. 1:1984.

L'ISO 7388 comprend les parties suivantes, présentées sous le titre général Queues d'outils à conicité 7/24

pour changement automatique d'outils:

⎯ Partie 1: Dimensions et désignation des queues de formes A, AD, AF, U, UD et UF

⎯ Partie 2: Dimensions et désignation des queues de formes J, JD et JF
⎯ Partie 3: Tirettes pour queues de formes AC, AD, AF, UC, UD, UF, JD et JF
© ISO 2007 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 7388-1:2007(F)
Introduction

L'objet de l'ISO 7388 est d'intégrer des normes existantes, qui sont plus généralement utilisées comme des

normes industrielles. De plus, les différents développements concernant la lubrification et la puce ont été pris

en compte.
iv © ISO 2007 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 7388-1:2007(F)
Queues d'outils à conicité 7/24 pour changement automatique
d'outils —
Partie 1:
Dimensions et désignation des queues de formes A, AD, AF, U,
UD et UF
1 Domaine d'application

La présente partie de l'ISO 7388 spécifie les dimensions des queues d'outils à conicité 7/24 pour changement

automatique de formes A, AD, AF, U, UD et UF (avec deux compléments possibles pour chacune) à utiliser

sur des machines à dispositifs de préhension automatique pour amener l'outil du magasin à la broche et vice

versa. Ces outils sont conçus avec la plupart des dimensions importantes pour l'utilisation dans les nez de

broche conformes à l'ISO 9270.
2 Références normatives

Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les

références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du

document de référence s'applique (y compris les éventuels amendements).

ISO 2768-1, Tolérances générales — Partie 1: Tolérances pour dimensions linéaires et angulaires non

affectées de tolérances individuelles

ISO 2768-2, Tolérances générales — Partie 2: Tolérances géométriques pour éléments non affectés de

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.