ISO 7573:2008
(Main)Technical product documentation — Parts lists
Technical product documentation — Parts lists
ISO 7573:2008 provides minimum requirements for parts lists to provide necessary information, e.g. for the production, procurement or maintenance of the parts. It covers manual as well as computer-generated parts lists.
Documentation technique de produits — Nomenclatures de composants
Tehnične risbe - Kosovnice
Ta mednarodni standard zagotavlja minimalne zahteve za kosovnice za zagotavljanje potrebnih informacij, t.j. izdelavo, naročilo ali vzdrževanje delov. Ta mednarodni standard zajema ročno kot tudi računalniško izdelane kosovnice.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 7573:2010
01-marec-2010
1DGRPHãþD
SIST ISO 7573:1995
7HKQLþQHULVEH.RVRYQLFH
Technical product documentation - Parts lists
Documentation technique de produits - Nomenclatures de composants
Ta slovenski standard je istoveten z: ISO 7573:2008
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
SIST ISO 7573:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 7573:2010
---------------------- Page: 2 ----------------------
SIST ISO 7573:2010
INTERNATIONAL ISO
STANDARD 7573
Second edition
2008-11-01
Technical product documentation —
Parts lists
Documentation technique de produits — Nomenclatures de composants
Reference number
ISO 7573:2008(E)
©
ISO 2008
---------------------- Page: 3 ----------------------
SIST ISO 7573:2010
ISO 7573:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 7573:2010
ISO 7573:2008(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General .2
5 Parts lists arrangement.2
5.1 Position.2
5.2 Data fields for parts lists.3
Annex A (informative) Examples of layout arrangements for parts lists .5
Bibliography.8
© ISO 2008 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 7573:2010
ISO 7573:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Direct
...
INTERNATIONAL ISO
STANDARD 7573
Second edition
2008-11-01
Technical product documentation —
Parts lists
Documentation technique de produits — Nomenclatures de composants
Reference number
ISO 7573:2008(E)
©
ISO 2008
---------------------- Page: 1 ----------------------
ISO 7573:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 7573:2008(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 General .2
5 Parts lists arrangement.2
5.1 Position.2
5.2 Data fields for parts lists.3
Annex A (informative) Examples of layout arrangements for parts lists .5
Bibliography.8
© ISO 2008 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 7573:2008(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7573 was prepared by Technical Committee ISO/TC 10, Technical product documentation,
Subcommittee SC 1, Basic conventions.
This second edition cancels and replaces the first ed
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.