ISO 9452:1989
(Main)Woodworking machines — Crosswise veneer splicing machines — Nomenclature
Woodworking machines — Crosswise veneer splicing machines — Nomenclature
Specifies the nomenclature appropriate to the various parts of these veneering splicing machines in order to assist manufacturers and users in the identification of these parts. Gives in addition to terms used in two of the three official ISO languages (English adn French) the equivalent terms in the German, Spanish and Italian languages.
Machines à bois — Machines à jointer les placages transversalement — Nomenclature
General Information
Standards Content (Sample)
INTERNATIONAL
STANDARD
9452
First edition
Premiere edition
NORME
1989-08-01
INTERNATIONALE
Woodworking machines - Crosswise veneer
splicing machines - Nomenclature
Machines 6 bois - Machines ti jointer les
placages transversalement - Nomenclature
Reference number
Numero de reference
ISO 9452 : 1989 (E/F)
---------------------- Page: 1 ----------------------
ISO 9452 : 1989 (E/F)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of
national Standards bodies (ISO member bedies). The work of preparing International
Standards is normally carried out through ISO technical committees. Esch member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to
the member bodies for approval before their acceptance as International Standards by
the ISO Council. They are approved in accordance with ISO procedures requiring at
least 75 % approval by the member bodies voting.
International Standard ISO 9452 was prepared by Technical Committee ISO/TC 39,
Machine took.
Annex A of this International Standard is for information only.
international Organization for Standardization
Case postale 56 l CH-121 1 Geneve 20 l Switzerland
Printed in Switzerland/lmprime en Suisse
ii
---------------------- Page: 2 ----------------------
ISO 9452 : 1989 (E/F)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une federation mondiale
d’organismes nationaux de normalisation (comites membres de I’ISO). L’elaboration
des Normes internationales est en general confiee aux comites techniques de I’ISO.
Chaque comite membre interesse par une etude a Ie droit de faire Partie du comite
technique cr66 a cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec I’ISO participent egalement aux travaux. L’ISO col-
labore etroitement avec Ia Commission electrotechnique internationale (GEI) en ce qui
concerne Ia normalisation electrotechnique.
Les projets de Normes internationales adoptes par les comites techniques sont soumis
aux comites membres pour approbation, avant leur acceptation comme Normes inter-
nationales par Ie Conseil de I’ISO. Les Normes internationales sont approuvees confor-
mement aux procedures de I’ISO qui requierent I’approbation de 75 % au moins des
comites membres votants.
La Norme internationale ISO 9452 a etc elaboree par Ie comite technique ISO/TC 39,
Machines-outils.
A de Ia presente Norme internationale est donnee uniquement a titre d’infor-
L’annexe
mation.
. . .
Ill
---------------------- Page: 3 ----------------------
This page intentionally lefl blank
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD
ISO 9452: 1989 (E/F)
NORME INTERNATIONALE
Woodworking machines - Machines ti bois - Machines
ti jointer les placages
Crosswise veneer splicing
transversalement -
machines - Nomenclature
Nomenclature
1 Domaine d’application
1 Scope
This International Standard specifies the nomenclature appro- La presente Norme internationale indique Ia nomenclature
propre aux differentes Parties des machines a jointer les placa-
priate to the various Parts of crosswise veneer splicing
machines in Order to assist manufacturers and users in the iden- ges transversalement, afin d’aider les constructeurs et les utili-
sateurs dans I’identification de ces Parties.
tification of these Parts.
NOTE - In addition to terms used in two of the three official ISO NOTE - En complement des termes utilises dans deux des trois
languages (English and French), this International Standard gives the langues off icielles de I’ISO (anglais et francais), cette Norme internatio-
nale donne les termes equivalents dans les langues allemande, espa-
equivalent terms in the German, Spanish and Italian languages; these
are published under the responsibility of the member bodies for gnole et italienne; ces termes sont publies sous Ia responsabilite des
comites membres de I’Allemagne, R.F. (DIN), de I’Espagne (AENOR)
Germany, F.R. (DIN), Spain (AENOR) and Italy (UNI). However, only
the terms given in the official languages tan be considered as ISO et de I’ltalie (UNI). Toutefois, seuls les termes donnes dans les langues
officielles peuvent etre consideres comme etant des termes de I’ISO.
terms.
La presente Norme internationale s’applique aux machines
This International Standard applies to those machines desig-
nated by the number 31 Jl9.2 in ISO 7984l). designees sous Ie numero 31 .119.2 de I’ISO 7984’).
1) ISO 7984 : 1988, Woodworking machines - Technical classifi- 1) ISO 7984 : 1988, Machines 2 bols - Classifica tion technique des
cation of woodworking machines and auxiliary machines for wood- machines 2 travaier Ie bois et des machines auxiliaires 6 travaifler Ie
workng. bois.
1
---------------------- Page: 5 ----------------------
ISO 9452 : 1989 (E/F)
2 Nomenclature
m
-
ln
m
PI
m
-Cu’
m
cri
cv
------- -
ti
---------------------- Page: 6 ----------------------
ISO 9452 : 1989 (E/F)
French
English
Francais
Anglais
Reference
Repere
Machines a jointer les placages
Crosswise veneer splicing machines
transversalement
Ossature
1 Framework
Montants
Columns
1.1
Traverse centrale
1.2 Central traverse
Socle
Base
1.3
Deplacement des pieces etlou outils
Feed of workpiece and/or tools
2
Variate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.