ISO 4386-3:2018

Plain bearings — Metallic multilayer plain bearings — Part 3: Non-destructive penetrant testing

This document specifies a non‑destructive penetrant testing for determining bond defects and discontinuities in the sliding surface of the bearing. The penetration method is used to detect a) bond defects in the transitional area between the bearing backing/bearing material on the end faces and joint faces of multilayer plain bearings which cannot be detected by the ultrasonic testing method specified in ISO 4386‑1, and b) discontinuities in the sliding surface of the bearing. The penetration method is applicable, in principle, to finished multilayer plain bearings. The bond test is usually carried out on cast multilayer plain bearings, with a backing consisting of steel, cast steel or cast bronze. It can also be used as a non-production method to aid detection of manufacturing process defects with other bearing material types. Bearing backings which cannot be tin-plated, or only with difficulty, such as perlitic cast iron, rust-resistant steel and cast aluminium, cannot be tested since no bond is possible between the bearing material and bearing backing.

Paliers lisses — Paliers lisses métalliques multicouches — Partie 3: Contrôle non destructif par ressuage

Drsni ležaji - Večslojni kovinski ležaji - 3. del: Preskušanje s penetracijo brez porušitve

General Information

• Status: Published
• Publication Date: 16-Jul-2018
• ICS: 21.100.10 - Plain bearings
• Technical Committee: ISO/TC 123/SC 2 - Materials and lubricants, their properties, characteristics, test methods and testing conditions
• Drafting Committee: ISO/TC 123/SC 2 - Materials and lubricants, their properties, characteristics, test methods and testing conditions
• Current Stage: 9060 - Close of review
• Start Date: 04-Mar-2029
• Ref Project: SIST ISO 4386-3:2020 - Plain bearings - Metallic multilayer plain bearings - Part 3: Non-destructive penetrant testing

Relations

• Revises: ISO 4386-3:1992 - Plain bearings — Metallic multilayer plain bearings — Part 3: Non-destructive penetrant testing
• Effective Date: 04-Nov-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 4386-3:2020
01-september-2020
Drsni ležaji - Večslojni kovinski ležaji - 3. del: Preskušanje s penetracijo brez
porušitve
Plain bearings - Metallic multilayer plain bearings - Part 3: Non-destructive penetrant
testing
Paliers lisses - Paliers lisses métalliques multicouches - Partie 3: Contrôle non destructif
par ressuage
Ta slovenski standard je istoveten z: ISO 4386-3:2018
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 4386-3:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 4386-3:2020

---------------------- Page: 2 ----------------------
SIST ISO 4386-3:2020
INTERNATIONAL ISO
STANDARD 4386-3
Second edition
2018-07
Plain bearings — Metallic multilayer
plain bearings —
Part 3:
Non-destructive penetrant testing
Paliers lisses — Paliers lisses métalliques multicouches —
Partie 3: Contrôle non destructif par ressuage
Reference number
ISO 4386-3:2018(E)
©
ISO 2018

---------------------- Page: 3 ----------------------
SIST ISO 4386-3:2020
ISO 4386-3:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 4386-3:2020
ISO 4386-3:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Safety precautions . 1
5 Preparation of test surface . 2
5.1 General . 2
5.2 Mechanical pre-cleaning . 2
5.3 Chemical pre-cleaning . 2
5.4 Drying . 2
6 Application of penetrant . 2
7 Removal of excess penetrant. 2
8 Application of the developer . 3
8.1 General . 3
8.2 Restriction .
...

INTERNATIONAL ISO
STANDARD 4386-3
Second edition
2018-07
Plain bearings — Metallic multilayer
plain bearings —
Part 3:
Non-destructive penetrant testing
Paliers lisses — Paliers lisses métalliques multicouches —
Partie 3: Contrôle non destructif par ressuage
Reference number
ISO 4386-3:2018(E)
©
ISO 2018

---------------------- Page: 1 ----------------------
ISO 4386-3:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4386-3:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Safety precautions . 1
5 Preparation of test surface . 2
5.1 General . 2
5.2 Mechanical pre-cleaning . 2
5.3 Chemical pre-cleaning . 2
5.4 Drying . 2
6 Application of penetrant . 2
7 Removal of excess penetrant. 2
8 Application of the developer . 3
8.1 General . 3
8.2 Restriction . 3
9 Inspection . 3
9.1 Bond defects . 3
9.2 Sliding surface .
...