SIST EN ISO 10964:1998

Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993)

IEC 60335-2-103:2006+A1:2010 Deals with the safety of electric drives for horizontally and vertically moving gates, doors and windows for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480 V for other appliances. It also covers the hazards associated with the movement of the driven part.
This publication is to be read in conjunction with
IEC 60335-1:2010.
This consolidated version consists of the second edition (2006)  
and its amendment 1 (2010). Therefore, no need to order amendment in
addition to this publication.

Klebstoffe - Bestimmung der Drehfestigkeit von anaeroben Klebstoffen auf Befestigungselementen mit Gewinde (ISO 10964:1993)

Das in dieser Internationalen Norm beschriebene Prüfverfahren wird verwendet, um die Sicherungswirkung und Gewindeverbindungen anaerober Klebstoffe in Gewindeverbindungen vergleichend zu erfassen. Dieses Verfahren kann auch für andere Klebstoffarten benutzt werden, sofern dafür geeignet sind.

Adhésifs - Détermination des couples fonctionnels sur des fixations filetées collées avec des adhésifs anaérobies (ISO 10964:1993)

La CEI 60335-2-103:2006+A1:2010 Traite de la sécurité des motorisations électriques de portails, portes et fenêtres, à ouverture horizontale  ou verticale, pour usages domestiques et analogues, dont la tension assignée n'est pas supérieure à 250 V pour les appareils monophasés et à 480 V pour les autres appareils.  Elle couvre également les risques liés au mouvement de la partie entraînée.
Cette publication doit être lue conjointement avec la
CEI 60335-1:2010.
Cette version consolidée comprend la deuxième édition (2006) et
son amendement 1 (2010). Il n'est donc pas nécessaire de commander
l'amendement avec cette publication.

Lepila - Določanje torzijske trdnosti anaerobnih lepil na pritrdilnih elementih z navojem ali na vijačnih spojnih sredstvih (ISO 10964:1993)

General Information

• Status: Withdrawn
• Publication Date: 31-Jan-1998
• Withdrawal Date: 09-Jun-2009
• ICS: 83.180 - Adhesives
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 27-May-2009
• Due Date: 19-Jun-2009
• Completion Date: 10-Jun-2009
• Ref Project: EN ISO 10964:1997 - Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993)

Relations

• Replaced By: SIST EN 15865:2009 - Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified)
• Effective Date: 01-Jul-2009
• Replaced By: SIST EN 15865:2009 - Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10964:1998
01-februar-1998
/HSLOD'RORþDQMHWRU]LMVNHWUGQRVWLDQDHUREQLKOHSLOQDSULWUGLOQLKHOHPHQWLK]
QDYRMHPDOLQDYLMDþQLKVSRMQLKVUHGVWYLK,62
Adhesives - Determination of torque strength of anaerobic adhesives on threaded
fasteners (ISO 10964:1993)
Klebstoffe - Bestimmung der Drehfestigkeit von anaeroben Klebstoffen auf
Befestigungselementen mit Gewinde (ISO 10964:1993)
Adhésifs - Détermination des couples fonctionnels sur des fixations filetées collées avec
des adhésifs anaérobies (ISO 10964:1993)
Ta slovenski standard je istoveten z: EN ISO 10964:1997
ICS:
83.180 Lepila Adhesives
SIST EN ISO 10964:1998 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10964:1998

---------------------- Page: 2 ----------------------

SIST EN ISO 10964:1998

---------------------- Page: 3 ----------------------

SIST EN ISO 10964:1998

---------------------- Page: 4 ----------------------

SIST EN ISO 10964:1998

---------------------- Page: 5 ----------------------

SIST EN ISO 10964:1998

---------------------- Page: 6 ----------------------

SIST EN ISO 10964:1998
INTERNATIONAL IS0
STANDARD
10964
First edition
1993-08-I 5
Adhesives - Determination of torque
strength of anaerobic adhesives on
threaded fasteners
Adhksifs - D&termination des couples fonctionnels SW des fixations
filetkes co&es avec des adh&ifs anakrobies
Reference number
IS0 109643 993(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 10964:1998
IS0 10964:1993(E)
Foreword
IS0 (the International Organization for Standardization) is a worldwide
federation of national standards bodies (IS0 member bodies). The work
of preparing International Standards is normally carried out through IS0
technical committees. Each member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the International Electrotechnical Commission
(I EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard IS0 10964 was prepared by Technical Committee
ISOnC 61, Plastics, Sub-Committee SC 11, Products.
0 IS0 1993
All rights reserved. No part of this publication may be reproduced or utilized in any form or
by any means, electronic or mechanical, including photocopying and microfilm, without per-
mission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 10964:1998
INTERNATIONAL STANDARD IS0 10964:1993(E)
Adhesives - Determination of torque strength of
anaerobic adhesives on threaded fasteners
It is used to overcome friction in the thread and under
1 Scope
the bolt head.
The test method described in this International Stan-
dard is used to make comparative assessments of the 3.3 breakaway torque, TBA: Initial torque required
securing or locking effect of anaerobic adhesives used to break the bond measured at the first movement
in threaded assemblies. This method may be used for between the nut and the bolt, when unscrewing an
other types of adhesives, if considered suitable. unseated assembly (without spacer sleeve, see
figure 1).
Dimensions in millimetres
2 Normative references
General tolerances f 0,2 mm
Roughness value in micrometres
The following standards contain provisions which,
through reference in this text, constitute provisions
sliding friction
of this International Standard. At the time of publi-
Ra X2/-
cation, the editions indicated were valid. All standards
are subject to revision, and parties to agreements
based on this International Standard are encouraged
to investigate the possibility of applying the most re-
cent editions of the standards indicated below.
Members of IEC and IS0 maintain registers of cur-
rently valid International Standards.
IS0 291 :I 977, Plastics - Standard atmospheres for
M
T
conditioning and testing.
8
IS0 898-l : 1988, Mechanical properties of fasteners
- Part 1: Bolts, screws and studs.
IS0 898-2: 1992, Mechanical properties of fasteners
- Part 2: Nuts with specified proof load values -
Coarse thread. A
10
I
20
a
-- [//IO,01 [ A]
3 Definitions
47 HRC to 50 HRC hardness carbon steel.
Surface condition : corrosion and grease-free.
For the purposes of this International Standard, the
Figure 1 - Spacer sleeve
following definitions apply.
3.1 on torque, TON: Maximum torque required to
screw the nut onto a bolt precoated with adhesive.
3.4 breakloose torque, TBL: Initial torque required
3.2 input torque, T,,,,: Torque applied to introduce to decrease or eliminate the axial load in a preloaded
or increase the axial load in the assembly. assembly.

---------------------- Page: 9 ----------------------

SIST EN ISO 10964:1998
IS0 10964:1993(E)
3.5 prevailing torque, TP: Torque measured after
the initial breakage of the bond at a specified angle
of rotation of the nut. For testing against a specifi-
cation, the angle shall be 180”.
NOTES
1 A round-robin test program, recently performed, showed
there is no significant difference between prevailing torque
Nut clamping or
measured at 180” and prevailing torque determined as the
securing device
mean of the four torque readings determined at 90”, 180”,
270" and 360”.
Test specimen
2 For quality control or purposes other than testing the
Bolt clamping or
adhesive against a specification, other angles may be
securing device
agreed between the manufacturer and the purchaser of the
adhesive.
Mandrel
If prevailing torque is measured at an angle other than
180”, the angle shall be denoted by a subscript; i.e.
TssO. Otherwise, prevailing torque measured at 180”
shall be designated by TP.
Turning device
NOTE 3 The prevailing torque can be defined as 7&X
when not testing to a specification, Tmax being the maximum
torque measured within the first 360” rotation of the nut
after the initial breakage of the bond.
Figure 2 - Example of test apparatus with
graphic recording
4 Principle
The test method consists of determining the torque
required to unscrew a bonded nut and bolt assembly,
including the initial torque required to break the bond,
6 Test specimens
and the torque measured after turning the nut 180”.
The torque strengths are determined for unseated
assemblies and for seated assemblies preloaded with
a specified input torque.
6.1 For testing against a specification, the test
specimen shall be an Ml 0 x 38, property class 8.8,
zinc-phosphated steel bolt and a similar Ml0 nut,
specified in IS0 898-l and IS0 898-2.
5 Apparatus
NOTE 4 Any size and surface finish of fastener combi-
nation may be used by agreement between the interested
parties.
5.1 Test machine with graphic recording, con-
sisting of a clamping device to secure the bolt head,
All fasteners used in unseated assemblies shall have
a device for turning the nut at a constant speed, a
a radial gap of 0,l mm to 0,2 mm on the minor di-
torque-measuring device (see figure2) and a recorder
ameter. The cutting oil used in their manufacture shall
with a response time of 1 ms or less.
be lanolin-free.
If a recorder is not used, a data storage system shall
be employed so that the torque data as a function of
6.2 Degrease all nuts and bolts in a permitted
the angle of turning can be recalled and plotted at a
cleaning medium, store in a desiccator at
later time.
23 “C + 2 “C, and keep them clean. Use degreased
specimens within four days or discard.
5.2 Test machine with direct reading, consisting
of a clamping device to secure the head of the bolt,
and a torque wrench accurate to + 5 % (see 6.3 The specimens shall be conditioned and tested
in one of the standard laboratory atmospheres speci-
figure 3).
fied in IS0 291, which shall be stated in the test re-
port.

---------------------- Page: 10 ----------------------

SIST EN ISO 10964:1998
INTERNATIONAL STANDARD IS0 10964:1993(E)
Adhesives - Determination of torque strength of
anaerobic adhesives on threaded fasteners
It is used to overcome fri
...