SIST EN ISO 14273:2016

Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds (ISO 14273:2016)

This International Standard specifies specimen dimensions and a testing procedure for tensile shear testing of spot and embossed projection welds, in overlapping sheets, in any metallic material of thickness 0,5 mm to 10 mm, where the welds have a maximum diameter of 7√t (where t is the sheet thickness in mm).
The object of tensile shear testing is to determine the tensile shear force that the test specimen can
sustain.

Probenmaße und Verfahren für die Scherzugprüfung an Widerstandspunkt-, Rollennaht- und Buckelschweißungen mit geprägten Buckeln (ISO 14273:2016)

Diese Internationale Norm legt die Probenmaße und das Verfahren für die Scherzugprüfung an Punkt-, Rollennaht- und Buckelschweißverbindungen mit geprägten Buckeln an überlappten Blechen aus beliebigen metallischen Werkstoffen der Blechdicke von 0,5 mm bis 10 mm fest, wobei die Schweißverbindungen einen maximalen Durchmesser von t7aufweisen (dabei ist t die Blechdicke in mm). Bei Schweißverbindungen mit einem Durchmesser von 5t bis 7t kann der Wert der Scherzugfestigkeit zu klein bewertet sein, wenn die empfohlenen Probenmaße verwendet werden.
Das Ziel der Scherzugprüfung ist es, die maximale Scherzugkraft zu bestimmen, die die Probe ertragen kann.

Dimensions des éprouvettes et mode opératoire pour l'essai de cisaillement des soudures par résistance par points, à la molette et par bossages (ISO 14273:2016)

ISO 14273:2016 spécifie les dimensions des éprouvettes, ainsi qu'un mode opératoire s'appliquant aux essais de cisaillement des soudures par résistance par points et par bossages, réalisées sur des tôles soudées par recouvrement, dans tout matériau métallique d'une épaisseur de 0,5 mm à 10 mm, où les soudures ont un diamètre maximal de 7√t (où t est l'épaisseur de la tôle, en millimètres).
L'essai de traction-cisaillement vise à déterminer la charge maximale de traction-cisaillement qu'une éprouvette peut supporter.

Mere vzorcev in postopek za strižno preskušanje uporovnih točkovnih, kolutnih in bradavičnih zvarov (ISO 14273:2016)

Ta mednarodni standard določa mere vzorcev in postopek za natezno strižno preskušanje točkovnih in bradavičnih zvarov, v prekrivajočih se slojih, v katerem koli kovinskem materialu debeline 0,5 do 10 mm, pri čemer je največji premer zvarov 7√t (t je debelina sloja v mm).
Cilj natezno strižnega preskušanja je določiti natezno strižno silo, ki jo lahko preskusni vzorec
prenese.

General Information

• Status: Published
• Public Enquiry End Date: 05-Oct-2014
• Publication Date: 06-Jun-2016
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: VAR - Welding
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 25-May-2016
• Due Date: 30-Jul-2016
• Completion Date: 07-Jun-2016
• Ref Project: EN ISO 14273:2016 - Resistance welding - Destructive testing of welds - Specimen dimensions and procedure for tensile shear testing resistance spot and embossed projection welds (ISO 14273:2016)

Relations

• Replaces: SIST EN ISO 14273:2002 - Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds (ISO 14273:2000)
• Effective Date: 01-Jul-2016
• Replaces: SIST EN ISO 14273:2002 - Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds (ISO 14273:2000)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14273:2016
01-julij-2016
1DGRPHãþD
SIST EN ISO 14273:2002
0HUHY]RUFHYLQSRVWRSHN]DVWULåQRSUHVNXãDQMHXSRURYQLKWRþNRYQLKNROXWQLKLQ
EUDGDYLþQLK]YDURY,62
Specimen dimensions and procedure for shear testing resistance spot, seam and
embossed projection welds (ISO 14273:2016)
Probenmaße und Verfahren für die Scherzugprüfung an Widerstandspunkt-, Rollennaht-
und Buckelschweißungen mit geprägten Buckeln (ISO 14273:2016)
Dimensions des éprouvettes et mode opératoire pour l'essai de cisaillement des
soudures par résistance par points, à la molette et par bossages (ISO 14273:2016)
Ta slovenski standard je istoveten z: EN ISO 14273:2016
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
SIST EN ISO 14273:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14273:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 14273:2016


EN ISO 14273
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2016
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 14273:2001
English Version

Resistance welding - Destructive testing of welds -
Specimen dimensions and procedure for tensile shear
testing resistance spot and embossed projection welds
(ISO 14273:2016)
Soudage par résistance - Essais destructifs des Widerstandsschweißen - Zerstörende Prüfung von
soudures - Dimensions des éprouvettes et mode Schweißverbindungen - Probenmaße und Verfahren
opératoire pour l'essai de traction-cisaillement des für die Scherzugprüfung an Widerstandspunkt-,
soudures par résistance par points et par bossages Rollennaht- und Buckelschweißungen mit geprägten
(ISO 14273:2016) Buckeln (ISO 14273:2016)
This European Standard was approved by CEN on 13 December 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14273:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14273:2016
EN ISO 14273:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 14273:2016
EN ISO 14273:2016 (E)
European foreword
This document (EN ISO 14273:2016) has been prepared by IIW International Institute of Welding in
collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2016, and conflicting national standards
shall be withdrawn at the latest by September 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 14273:2001.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 14273:2016 has been approved by CEN as EN ISO 14273:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 14273:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 14273:2016
INTERNATIONAL ISO
STANDARD 14273
Second edition
2016-03-01
Resistance welding — Destructive
testing of welds — Specimen
dimensions and procedure for tensile
shear testing resistance spot and
embossed projection welds
Soudage par résistance — Essais destructifs des soudures —
Dimensions des éprouvettes et mode opératoire pour l’essai de
traction-cisaillement des soudures par résistance par points et par
bossages
Reference number
ISO 14273:2016(E)
©
ISO 2016

---------------------- Page: 7 ----------------------

SIST EN ISO 14273:2016
ISO 14273:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 14273:2016
ISO 14273:2016(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test pieces and specimens . 1
5 Test equipment and testing procedure . 3
6 Test report . 5
Annex A (informative) Specimen size — Saturated strength condition . 6
Bibliography . 8
© ISO 2016 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 14273:2016
ISO 14273:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users
...