SIST EN ISO 7711-1:2000
(Main)Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging (ISO 7711-1:1997)
Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging (ISO 7711-1:1997)
Specifies dimensional and other relevant requirements for the 14 most commonly used shapes of dental diamond instruments, including a quality control for these instruments. Replaces ISO 7711:1984.
Zahnärztliche rotierende Instrumente - Diamantinstrumente - Teil 1: Maße, Anforderungen, Kennzeichnung und Verpackung (ISO 7711-1:1997)
Dieser Teil der ISO 7711 legt maßliche und andere relevante Anforderungen für die 14 am häufigsten verwendeten Formen von zahnärztlichen Diamantinstrumenten fest und enthält eine Qualitätskontrolle für diese Instrumente.
Instruments rotatifs dentaires - Instruments diamantés - Partie 1: Dimensions, exigences, marquage et emballage (ISO 7711-1:1997)
L'IEC 60695-1-20:2016 donne des lignes directrices concernant l'allumabilité des produits électrotechniques et des matériaux dont ils sont constitués. Elle fournit des lignes directrices sur: les principes de l'allumabilité; le choix des méthodes d'essai appropriées, et l'utilisation et l'interprétation des résultats.
Cette première édition de l'IEC 60695-1-20 annule et remplace la première édition de l'IEC TS 60695-1-20 parue en 2008. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- l'ISO 5660-1 a été ajoutée aux références normatives;
- les définitions de "pyrolyse" et de "court-circuit" ont été ajoutées à l'Article 3;
- des parties de l'introduction ont été déplacées vers l'Article 5 et font maintenant partie du texte normatif;
- et l'Article 5 comprend maintenant plusieurs énoncés obligatoires.
La présente partie de l'IEC 60695 est destinée à être utilisée par les comités d'études pour l'établissement de leurs normes conformément aux principes exposés dans le Guide IEC 104 et dans le Guide ISO/IEC 51.
Mots clés: Risque du feu, Méthode d'essai du feu, Ingénierie de la sécurité incendie, Allumabilité
Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging (ISO 7711-1:1997)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging (ISO 7711-1:1997)Zahnärztliche rotierende Instrumente - Diamantinstrumente - Teil 1: Maße, Anforderungen, Kennzeichnung und Verpackung (ISO 7711-1:1997)Instruments rotatifs dentaires - Instruments diamantés - Partie 1: Dimensions, exigences, marquage et emballage (ISO 7711-1:1997)Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging (ISO 7711-1:1997)11.060.25Dental instrumentsICS:Ta slovenski standard je istoveten z:EN ISO 7711-1:1998SIST EN ISO 7711-1:2000en01-januar-2000SIST EN ISO 7711-1:2000SLOVENSKI
STANDARD
SIST EN ISO 7711-1:2000
SIST EN ISO 7711-1:2000
SIST EN ISO 7711-1:2000
SIST EN ISO 7711-1:2000
SIST EN ISO 7711-1:2000
INTERNATIONAL STANDARD Is0 771 I=1 First edition 1997-02-I 5 Dental rotary instruments - Diamond instruments - I Part 1: Dimensions, requirements, marking and packaging Instruments rota tifs den takes - Instruments diaman t&s - Par-tie 7: Dimensions, exlgences, marquage et emballage Reference number IS0 771 l-l :I 997(E) SIST EN ISO 7711-1:2000
IS0 7711-1:1997(E~ @ IS0 Contents Scope . Normative references . Symbols . Requirements . Testing . Quality control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IPage 1 1 1 2 41 47 47 48 0 IS0 1997 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Organization for Standardization Case postale 56 l CH-121 I Geneve 20 l Switzerland Internet central@iso.ch x.400 c=ch; a=40Onet; p=iso; o=isocs; s=centraI Printed in Switzerland ii SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 771 l-l was prepared by Technical Committee lSO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments. This first edition of IS0 771 l-l cancels and replaces the first edition of IS0 7711 :I 984, which has been technically revised. IS0 7711 consists of the following parts, under the general title Dental rotary instruments - Diamond instruments: - Part 1: Dimensions, requirements, marking and packaging - Part 2: Discs - Part 3: Grit sizes, designation and colour code . . . III SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) @ IS0 Introduction This part of IS0 7711 is one of a series of standards relating to dental rotary instruments. This first edition of IS0 771 l-l contains the updated specifications for diamond instruments given in IS0 7711:1984. It was also aligned in several details with the other International Standards on dental rotary instruments. The various dimensional and other requirements specified for diamond instruments are those considered important to ensure the interchange- ability and safe usage of these instruments in the practice of dentistry. The nominal diameters of the working part listed in tables 1 to 48 comply with the diameters specified in IS0 2157. The diameters listed in the first column (preferred diameters) should be used in preference. Attention is drawn to IS0 6360, which specifies a 15-digit number coding system for the identification of dental rotary instruments of all types. SIST EN ISO 7711-1:2000
INTERNATIONAL STANDARD @ Iso IS0 7711-1:1997(E) Dental rotary instruments - Diamond instruments - Part 1: Dimensions, requirements, marking and packaging 1 Scope This part of IS0 7711 specifies dimensional and other relevant requirements for the 14 most commonly used shapes of dental diamond instruments, including a quality control for these instruments. It is envisaged to update this part of IS0 7711 at each periodical revision to cover at that time the commonly used shapes and other specifications. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 7711. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 7711 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IS0 1797-l :I 992, Dental rotary instruments - Shanks - Part I: Shanks made of metals. IS0 2157:1992, Dental rotary instruments - Nominal diameters and designation code number. IS0 3696: 1987, Water for analytical laboratory use - Specification and test methods. IS0 6360-I :I 985, Dental rotary instruments - Number coding system - Part 1: General characteris tics. IS0 6360-2: 1986, Dental rotary instruments - Number coding system - Part 2: Shape and specific characteristics. IS0 771 l-3:1 992, Dental rotary instruments - Diamond instruments - Part 3: Grit sizes, designation and co/our code. IS0 8325: 1985, Dental rotary instruments - Test methods. 3 Symbols For the purposes of this part of IS0 7711, the following symbo 1s aPP IY . . dl diameter of working part; head diameter 1 SIST EN ISO 7711-1:2000
. IS0 7711=1:1997(E) & neck diameter, measured directly behind the diamond coating d3 diameter of the coated neck, measured at the smallest diameter II length of the working part; head length /2 overall length a angle of the working part 4 Requirements 4.1 Materials 4.1.1 Shank The material of the shank shall comply with IS0 1797-1. 4.1.2 Working part The working part shall be made of diamond grit, bound in either metal, plastics or other suitable material at the discretion of the manufacturer. Grit sizes shall comply with IS0 771 l-3. 4.2 Shapes The shape of the working part shall be as specified in the appropriate figures 1 to 48. Variations of shape within the limited dimensions and the descriptions in the subclause titles are permitted. Testing shall be carried out in accordance with 5.1. 4.3 Dimensions 4.3.1 Overall length The overall length of the instrument, 12, is the sum of the fitting length of the shank and the length of the working part. In tables 1 to 48, “Standard” refers to instruments with standard fitting lengths of shank. For instruments with longer or shorter shank lengths, the overall length, 12, will vary accordingly. See IS0 1797-l :I 992, table 1, for fitting lengths of shanks. 4.3.2 Shank The shank shall be Type 1, 2 or 3 of IS0 1797-l. 4.3.3 Working part The dimensions of the working part shall be as specified in the appropriate tables 1 to 48. Testing shall be carried out in accordance with 5.1. SIST EN ISO 7711-1:2000
@ IS0 IS0 771 I-1:1997(E) 4.3.3.1 Round head (spherical) Figure I! Table 1 - Dimensions (see figure 1) Dimensions in millimetres Designation of nominal diameter Preferred diameters 4 cf;! 4 &2 rf:o,5 Shank Shank Shank Shank nom. tol. max. min. TVpe 1 TYPe 2 TYPe 3 TVpe 3 Standard Standard Standard Short 3 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.2 Round head (with collar) Figure 2 Table 2 - Dimensions (see figure 2) 009 0’9 010 LO &0,08 lwl r-- 012 1 I ' IL I 1,4 012 12 014 014 1,4 016 15 018 018 18 021 021 u 023 023 23 025 2,5 033 3,3 + 0,lO Dimensions in millimetres Shank Shank Shank Shank Type1 Type2 Type3 Type3 Standard Standard Standard Short 22,0 44,5 19,o 16,5 12 IL 0,5 4 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.3 Inverted cone head (inverted, truncated conical) Figure 3 Table 3 - Dimensions (see figure 3) Dimensions in millimetres, angles in degrees Designation of nominal diameter 4 d2 a h 12 + 0,5 Preferred diameters nom. max. Shank Shank Shank Shank min. TVpe 1 TVpe 2 Type 3 Type 3 Standard Standard Standard Short 5 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.4 Inverted cone head (with collar) Figure 4 Table 4 - Dimensions (see figure 4) Dimensions in millimetres, angles in degrees Designation of nominal diameter Preferred diameters 4 d2 d3 4 a 12 + 0,5 Shank Shank Shank Shank min. nom. tol. max. + 0,l Type 1 Type 2 Type 3 Type 3 Standard Standard Standard Short 017 0,68 0,60 008 03 0,78 0,68 2,0 8” to 14’ +0,08 009 019 0,84 0,74 010 LO 0,96 0,78 012 12 1 ,oo 0,88 IO” to 18” 014 1,4 I,04 0,98 22,0 44,5 19,0 16,5 22 016 13 I,10 I,04 018 13 +0,10 I,18 I,35 ~10”t022” 021 21 I,26 I,40 023 2,3 I,32 I,70 2,5 025 2,5 I,44 I,90 6 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.5 Wheel Figure 5 Table 5 - Dimensions (see figure 5) Dimensions in millimetres Designation of nominal diameter 12 + 0,5 Shank Shank Shank Shank TYPe 1 Type 2 TYPe 3 Type 3 Standard Standard Standard Short 22,0 44,5 19,o 16,5 d2 4 min. Preferred diameters max. 0,73 013 0,83 014 114 016 116 0,93 0,4 I 118 I,03 018 I I,05 0,5 021 211 023 2,3 I,23 I 025 1 215 I,25 I 027 I 2,7 I,43 I,45 I,53 I 033 I 313 I,63 I,67 053 I 035 1 3,5 I,77 I 037 1 3,7 I 040 1 4,o I,91 2,Ol 2,Ol 2,09 2,17 I 042 I 4,2 I 045 1 4,5 7 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.6 Wheel with collar Figure 6 Table 6 - Dimensions (see figure 6) Dimensions in millimetres Shank TYPe 3 Short 4.3.3.7 Cylindrical working part 4.3.3.7.1 Head length 3,0 mm * 4 * 4 m w Figure 7 Table 7 - Dimensions (see figure 7) Dimensions in millimetres I Designation I 4 12 of nominal diameter + 0,5 1 nom. 1 tol. / max. 1 + 0,3 1 j!/ia!d 1 j!/ia:d / j!:ia!d 008 018 1 030 1 I[ - 1 009 0'9 + 0,08 0,90 3,O 010 1’0 1 ,oo I 22,0 44,5 I 19,o 012 12 k 0,lO I,20 Shank Type 3 Short 16,5 8 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.7.2 Head length 4,0 mm (2 Figure 8 Table 8 - Dimensions (see figure 8) Dimensions in millimetres 010 LO +0,08 ’ 1 ,oo 012 12 I,20 - 014 410 114 I,35 22,o 44,5 19,o 1615 ' fO,lO 016 116 I,50 018 118 I,60 4.3.3.7.3 Head length 5,0 mm Figure 9 Table 9 - Dimensions (see figure 9) Dimensions in millimetres SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.7.4 Head length 6,0 mm Figure 10 Table 10 - Dimensions (see figure IO) Dimensions in millimetres Designation of nominal diameter I z2 It 0,5 Preferred diameters nom. max. + 0,3 Shank Shank Shank Shank TYPe 1 Type 2 Type 3 Type 3 Standard Standard Standard Short IO SIST EN ISO 7711-1:2000
@ IS0 IS0 771 ‘M:1997(EI) 4.3.3.7.5 Head length 8,0 mm Figure 11 Table 11 - Dimensions (see figure 11) Dimensions in millimetres Ix, F~~%iiieter 1 + F,, 016 I I 116 I I,50 018 I I 118 1 I,60 I 025 I 2,5 I I,85 11 Ik 0,3 80 24,O 44,5 22,0 Shank Type1 Standard 12 If:o,5 Shank Shank Type2 Type3 Standard Standard Shank Type3 Short 19,5 11 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) @ IS0 4.3.3.7.6 Head length IO,0 mm Figure 12 Table 12 - Dimensions (see figure 12) Dimensions in millimetres Designation of nominal diameter Preferred diameters 010 012 014 016 018 4 ~O,lO LO 12 114 I,6 118 d2 max. I,00 I,20 I,35 I,50 I,60 I,85 4 + 0,3 IO,0 12 f: 0,5 Shank Shank Shank Shank 1 2 Type 3 TYPe TVpe TVpe 3 Standard Standard Standard Short 26,O 44,5 24,O 21,5 12 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.8 Truncated conical working part 4.3.3.8.1 Head length 3,0 mm Figure 13 Table 13 - Dimensions (see figure 13) Dimensions in millimetres, angles in degrees Designation of nominal diameter Preferred diameters I + 0,08 max. 008 , 03 0,80 009 019 0,90 010 LO 1 ,oo a 21 III 0,3 12 + 0,5 Shank Shank Shank Shank TYPe 1 Type 2 Type 3 Type 3 Standard Standard Standard Short 3” to 6” 3,0 22,o 44,5 19,o 16,5 13 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.8.2 Head length 4,0 mm @ IS0 Figure 14 Table 14 - Dimensions (see figure 14) Dimensions in millimetres, angles in degrees of nominal diameter 14 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.8.3 Head length 6,0 mm Figure 15 Table 15 - Dimensions (see figure 15) Designation of nominal diameter d2 11 +O,l 1 max. j 010 LO 1 ,oo 2" to 6” 012 12 I,20 014 114 I,35 016 ‘16 I,50 018 118 I,60 3"to 7O 60 22,o 040 I 4,0 I 2,35 I 7Oto 12" 4.3.3.8.4 Head length 7,0 mm h + 0,3 Dimensions in millimetres, angles in degrees Shank Shank Shank Type1 Type2 Type3 Standard Standard Standard 44,5 21,0 18,5 I Shank Type3 Short I. Figure 16 Table 16 - Dimensions (see figure 16) Dimensions in millimetres, angles in degrees Designation of nominal diameter 12 + 0,5 I Preferred Shank Shank Shank Shank Shank Shank Shank Shank diameters + 0,l max. IL 0,3 TYPeI TYPeI Type2 Type2 Type3 Type3 Type3 Type3 Standard Standard Standard Standard Standard Standard Short Short I - I 035 I,85 5"to 9" 1 7,0 1 23,0 23,0 1 44,5 4415 1 21,0 21,0 1 1815 1815 1 15 SIST EN ISO 7711-1:2000
IS0 7711=1:l997(E) 4.3.3.8.5 Head length 8,0 mm w-e-- - - -- . ‘2 Figure 17 Table 17 - Dimensions (see figure 17) Dimensions in millimetres, angles in degrees 16 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711-1:1997(E) 4.3.3.8.6 Head length 9,0 mm Figure 18 Table 18 - Dimensions (see figure 18) Dimensions in millimetres, angles in degrees I Designation of nominal diameter I 4 d2 a 4 Preferred diameters + 0,l max. + 0,3 I 023 2,3 I,80 I 7 031 I 3,l I 2,35 I I 033 3,3 2,35 040 4,O 2,35 050 5,O 2,35 25,0 44,5 24,0 21,5 17 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.8.7 Head length IO,0 mm Figure 19 Table 19 - Dimensions (see figure 19) Dimensions in millimetres, angles in degrees 18 SIST EN ISO 7711-1:2000
0 IS0 IS0 7711=1:1997(E) 4.3.3.9 Hemispherical cylindrical working part 4.3.3.9.1 Head length 3,0 mm Figure 20 Table 20 - Dimensions (see figure 20) Designation of nominal diameter dl d2 4 12 + 0,5 Preferred diameters 008 009 010 Z!I 0,08 03 03 LO max. 0,80 0,90 I,00 Ii 0,3 3,O Shank Shank Shank Shank Type 1 Type2 Type3 Type 3 Standard Standard Standard Short 22,0 44,5 19,0 16,5 Dimensions in millimetres I 19 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.9.2 Head length 4,0 mm Figure 21 Table 21 - Dimensions (see figure 21) Dimensions in millimetres II nom. 1 tol. I I Designation I I d2 I I1 I 12 of nominal diameter 4 I . rn A I shank I _Shi + 0,5 ank Shank Shank max. t UJ ‘YPe ’ lYPe2 Type3 TVpe 3 Standard Standard Standard Short 009 03 0,90 010 LO A +0,08 - I,0 0 410 22,0 44,5 19,0 16,5 012 12 kO,lO I,20 r 014 - I 114 I . I I,35 I 20 SIST EN ISO 7711-1:2000
@ IS0 IS0 7711=1:1997(E) 4.3.3.9.3 Head length 6,0 mm Figure 22 Table 22 - Dimensions (see figure 22) Dimensions in millimetres of nominal diameter 21 SIST EN ISO 7711-1:2000
IS0 7711=1:1997(E) 4.3.3.9.4 Head length 8,0 mm 12 Figure 23 Table 23 - Dimensions (see figure 23) Dimensions in millimetres Designation of nominal diameter I LI +O,lO 1 max. 1 -10,3 014 184 I,35 88 016 15 I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.