SIST EN 302 502 V2.1.1:2017
(Main)Wireless Access Systems (WAS) - 5,8 GHz fixed broadband data transmitting systems - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Wireless Access Systems (WAS) - 5,8 GHz fixed broadband data transmitting systems - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document specifies technical characteristics and methods of measurements for Fixed Broadband Data
Transmitting Systems intended to operate in the 5,8 GHz band (5 725 MHz to 5 875 MHz). The present document is
equally applicable to systems utilizing integral or dedicated antennas.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
Brezžični dostopovni sistemi (WAS) - Fiksni širokopasovni sistemi za prenos podatkov na frekvenci 5,8 GHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument določa tehnične lastnosti in merilne metode za fiksne širokopasovne sisteme za prenos podatkov, ki delujejo v pasu 5,8 GHz (od 5725 MHz do 5875 MHz). Ta dokument se uporablja tudi za sisteme, ki uporabljajo vgrajene ali namenske antene.
Ta dokument zajema bistvene zahteve člena 3.2 direktive 2014/53/EU [i.1] pod pogoji iz dodatka A.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Wireless Access Systems (WAS) - 5,8 GHz fixed broadband data transmitting systems - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU35.110OmreževanjeNetworking33.060.01Radijske komunikacije na splošnoRadiocommunications in generalICS:Ta slovenski standard je istoveten z:ETSI EN 302 502 V2.1.1 (2017-03)SIST EN 302 502 V2.1.1:2017en01-maj-2017SIST EN 302 502 V2.1.1:2017SLOVENSKI
STANDARD
SIST EN 302 502 V2.1.1:2017
ETSI EN 302 502 V2.1.1 (2017-03) Wireless Access Systems (WAS); 5,8 GHz fixed broadband data transmitting systems; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 2
Reference REN/BRAN-0060021 Keywords access, broadband, digital, fixed networks, harmonised standard, multipoint ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 9 3.3 Abbreviations . 9 4 Technical requirements specification . 10 4.1 Environmental profile . 10 4.2 Conformance requirements . 10 4.2.1 Designation of centre frequencies and frequency error . 10 4.2.1.1 Definition . 10 4.2.1.2 Limits . 10 4.2.1.3 Conformance . 10 4.2.2 Transmitter RF output power, EIRP and EIRP spectral density . 10 4.2.2.1 Definition . 10 4.2.2.2 Limits . 11 4.2.2.3 Conformance . 11 4.2.3 Transmitter unwanted emissions . 11 4.2.3.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 11 4.2.3.1.1 Definition. 11 4.2.3.1.2 Limits . 11 4.2.3.1.3 Conformance . 11 4.2.3.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 11 4.2.3.2.1 Definition. 11 4.2.3.2.2 Limits . 12 4.2.3.2.3 Conformance . 12 4.2.4 Transmitter Power Control (TPC) . 12 4.2.4.1 Definition . 12 4.2.4.2 Limit . 12 4.2.4.3 Conformance . 12 4.2.5 Receiver spurious emissions . 13 4.2.5.1 Definition . 13 4.2.5.2 Limit . 13 4.2.5.3 Conformance . 13 4.2.6 Dynamic Frequency Selection (DFS) . 13 4.2.6.1 General Requirements . 13 4.2.6.2 DFS Technical requirements specifications . 13 4.2.6.2.1 Channel availability check and channel revalidation period . 13 4.2.6.2.2 In-Service Monitoring . 14 4.2.6.2.3 Channel Shutdown. 14 4.2.6.2.4 Non-Occupancy Period . 15 4.2.7 Receiver Blocking . 15 4.2.7.1 Applicability. 15 4.2.7.2 Definition . 15 4.2.7.3 Performance Criteria . 15 4.2.7.4 Limits . 16 4.2.7.5 Conformance . 16 4.2.8 User Access Restrictions . 16 SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 4 4.2.8.1 Definition . 16 4.2.8.2 Requirement . 16 5 Testing for compliance with technical requirements . 17 5.1 Environmental conditions for testing . 17 5.1.1 Introduction. 17 5.1.2 Environmental specifications . 17 5.2 Interpretation of the measurement results . 17 5.3 Definition of other test conditions . 18 5.3.1 Test sequences and Traffic load . 18 5.3.1.1 General test transmission sequences . 18 5.3.1.2 Test transmission sequences for DFS tests . 18 5.3.2 Test frequencies . 18 5.3.3 Presentation of Equipment . 18 5.3.3.1 Integrated and Dedicated antennas . 18 5.4 Radio test suites . 19 5.4.1 Product information . 19 5.4.2 Frequency error . 19 5.4.2.1 Test conditions . 19 5.4.2.2 Test methods . 19 5.4.2.2.1 Conducted measurement. 19 5.4.2.2.2 Radiated measurement . 20 5.4.3 Transmitter RF Output Power, EIRP, TPC and EIRP Spectral Density . 20 5.4.3.1 Test conditions . 20 5.4.3.2 Test method . 20 5.4.3.2.1 Conducted measurement. 20 5.4.3.2.2 Radiated measurement . 23 5.4.4 Transmitter unwanted emissions . 23 5.4.4.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 23 5.4.4.1.1 Test conditions . 23 5.4.4.1.2 Test method . 23 5.4.4.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 24 5.4.4.2.1 Test conditions . 24 5.4.4.2.2 Test method . 24 5.4.5 Receiver spurious emissions . 25 5.4.5.1 Test conditions . 25 5.4.5.2 Test method . 25 5.4.5.2.1 Conducted tests . 25 5.4.5.2.2 Radiated tests . 26 5.4.6 Dynamic Frequency Selection (DFS) . 26 5.4.6.1 Test conditions . 26 5.4.6.1.1 Introduction . 26 5.4.6.1.2 Selection of Radar Test Signals . 26 5.4.6.1.3 Test Set-Up . 26 5.4.6.2 Test Method . 27 5.4.6.2.1 Conducted measurement. 27 5.4.6.2.2 Radiated measurement . 31 5.4.7 Receiver Blocking . 32 5.4.7.1 Test conditions . 32 5.4.7.2 Test Method . 32 5.4.7.2.1 Conducted measurements . 32 5.4.7.2.2 Radiated measurements . 33 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 34 Annex B (normative): Test sites and arrangements for radiated measurements . 35 B.1 Test sites . 35 B.1.1 Open air test sites . 35 B.1.2 Anechoic chamber . 36 B.1.2.1 General . 36 B.1.2.2 Description . 36 SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 5 B.1.2.3 Influence of parasitic reflections . 36 B.1.2.4 Calibration and mode of use . 37 B.2 Test antenna . 38 B.3 Substitution antenna . 39 Annex C (normative): General description of measurement . 40 C.1 Conducted measurements . 40 C.2 Radiated measurements . 40 C.3 Substitution measurement . 41 Annex D (normative): Dynamic Frequency Selection (DFS) parameters . 42 Annex E (informative): Bibliography . 45 Annex F (informative): Change History . 46 History . 47
SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations.
National transposition dates Date of adoption of this EN: 6 March 2017 Date of latest announcement of this EN (doa): 30 June 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2017 Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document covers 5,8 GHz high performance Broadband Fixed Wireless Access systems (BFWA) including equipment which is used in wireless local area networks. Such networks provide high speed data communications in between devices connected to the wireless infrastructure. SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 7 1 Scope The present document specifies technical characteristics and methods of measurements for Fixed Broadband Data Transmitting Systems intended to operate in the 5,8 GHz band (5 725 MHz to 5 875 MHz). The present document is equally applicable to systems utilizing integral or dedicated antennas. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. [i.3] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1". [i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2". SIST EN 302 502 V2.1.1:2017
ETSI ETSI EN 302 502 V2.1.1 (2017-03) 8 [i.6] CEPT/ECC Report 68 (Riga, June 2005): "Compatibility studies in the band 5725-5875 MHz between Fixed Wireless Access (FWA) systems and other systems". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the following apply: antenna assembly: combination of the antenna (integral or dedicated), its coaxial cable and if applicable, its antenna connector and associated switching components available channel: channel identified as usable as an Operating Channel Broadband Fixed Wireless Access (BFWA): operation of fixed Point to Point or fixed Point to Multipoint wireless devices or systems used to connect fixed locations burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which no intentional transmission is made dedicated antenna: antenna external to the equipment, using an antenna connector with a cable or a wave-guide NOTE: The antenna has been designed or developed for one or more specific types of equipment. It is the combination of dedicated antenna and radio equipment that is expected to be compliant with the regulations. environmental profile: declared range of environmental conditions under which equipment within the scope of the present document is required to be compliant in-service monitoring: mechanism to check a channel in use by the device for the presence of a radar signal with a level above the Interference Detection Threshold integral antenna: antenna designed as a fixed part of the equipment, without the use of an external connector and as such which cannot be disconnected from the equi
...
ETSI EN 302 502 V2.1.1 (2017-03)
HARMONISED EUROPEAN STANDARD
Wireless Access Systems (WAS);
5,8 GHz fixed broadband data transmitting systems;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 302 502 V2.1.1 (2017-03)
Reference
REN/BRAN-0060021
Keywords
access, broadband, digital, fixed networks,
harmonised standard, multipoint
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 502 V2.1.1 (2017-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specification . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Designation of centre frequencies and frequency error . 10
4.2.1.1 Definition . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Transmitter RF output power, EIRP and EIRP spectral density . 10
4.2.2.1 Definition . 10
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions . 11
4.2.3.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 11
4.2.3.1.1 Definition. 11
4.2.3.1.2 Limits . 11
4.2.3.1.3 Conformance . 11
4.2.3.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 11
4.2.3.2.1 Definition. 11
4.2.3.2.2 Limits . 12
4.2.3.2.3 Conformance . 12
4.2.4 Transmitter Power Control (TPC) . 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 12
4.2.4.3 Conformance . 12
4.2.5 Receiver spurious emissions . 13
4.2.5.1 Definition . 13
4.2.5.2 Limit . 13
4.2.5.3 Conformance . 13
4.2.6 Dynamic Frequency Selection (DFS) . 13
4.2.6.1 General Requirements . 13
4.2.6.2 DFS Technical requirements specifications . 13
4.2.6.2.1 Channel availability check and channel revalidation period . 13
4.2.6.2.2 In-Service Monitoring . 14
4.2.6.2.3 Channel Shutdown. 14
4.2.6.2.4 Non-Occupancy Period . 15
4.2.7 Receiver Blocking . 15
4.2.7.1 Applicability. 15
4.2.7.2 Definition . 15
4.2.7.3 Performance Criteria . 15
4.2.7.4 Limits . 16
4.2.7.5 Conformance . 16
4.2.8 User Access Restrictions . 16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 502 V2.1.1 (2017-03)
4.2.8.1 Definition . 16
4.2.8.2 Requirement . 16
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Environmental specifications . 17
5.2 Interpretation of the measurement results . 17
5.3 Definition of other test conditions . 18
5.3.1 Test sequences and Traffic load . 18
5.3.1.1 General test transmission sequences . 18
5.3.1.2 Test transmission sequences for DFS tests . 18
5.3.2 Test frequencies . 18
5.3.3 Presentation of Equipment . 18
5.3.3.1 Integrated and Dedicated antennas . 18
5.4 Radio test suites . 19
5.4.1 Product information . 19
5.4.2 Frequency error . 19
5.4.2.1 Test conditions . 19
5.4.2.2 Test methods . 19
5.4.2.2.1 Conducted measurement. 19
5.4.2.2.2 Radiated measurement . 20
5.4.3 Transmitter RF Output Power, EIRP, TPC and EIRP Spectral Density . 20
5.4.3.1 Test conditions . 20
5.4.3.2 Test method . 20
5.4.3.2.1 Conducted measurement. 20
5.4.3.2.2 Radiated measurement . 23
5.4.4 Transmitter unwanted emissions . 23
5.4.4.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 23
5.4.4.1.1 Test conditions . 23
5.4.4.1.2 Test method . 23
5.4.4.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 24
5.4.4.2.1 Test conditions . 24
5.4.4.2.2 Test method . 24
5.4.5 Receiver spurious emissions . 25
5.4.5.1 Test conditions . 25
5.4.5.2 Test method . 25
5.4.5.2.1 Conducted tests . 25
5.4.5.2.2 Radiated tests . 26
5.4.6 Dynamic Frequency Selection (DFS) . 26
5.4.6.1 Test conditions . 26
5.4.6.1.1 Introduction . 26
5.4.6.1.2 Selection of Radar Test Signals . 26
5.4.6.1.3 Test Set-Up . 26
5.4.6.2 Test Method . 27
5.4.6.2.1 Conducted measurement. 27
5.4.6.2.2 Radiated measurement . 31
5.4.7 Receiver Blocking . 32
5.4.7.1 Test conditions . 32
5.4.7.2 Test Method . 32
5.4.7.2.1 Conducted measurements . 32
5.4.7.2.2 Radiated measurements . 33
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 34
Annex B (normative): Test sites and arrangements for radiated measurements . 35
B.1 Test sites . 35
B.1.1 Open air test sites . 35
B.1.2 Anechoic chamber . 36
B.1.2.1 General . 36
B.1.2.2 Description . 36
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 502 V2.1.1 (2017-03)
B.1.2.3 Influence of parasitic reflections . 36
B.1.2.4 Calibration and mode of use . 37
B.2 Test antenna . 38
B.3 Substitution antenna . 39
Annex C (normative): General description of measurement . 40
C.1 Conducted measurements . 40
C.2 Radiated measurements . 40
C.3 Substitution measurement . 41
Annex D (normative): Dynamic Frequency Selection (DFS) parameters . 42
Annex E (informative): Bibliography . 45
Annex F (informative): Change History . 46
History . 47
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 502 V2.1.1 (2017-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 6 March 2017
Date of latest announcement of this EN (doa): 30 June 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2017
Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document covers 5,8 GHz high performance Broadband Fixed Wireless Access systems (BFWA) including
equipment which is used in wireless local area networks. Such networks provide high speed data communications in
between devices connected to the wireless infrastructure.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 502 V2.1.1 (2017-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Fixed Broadband Data
Transmitting Systems intended to operate in the 5,8 GHz band (5 725 MHz to 5 875 MHz). The present document is
equally applicable to systems utilizing integral or dedicated antennas.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of
environmental conditions; Introduction".
[i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 1".
[i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 2".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 302 502 V2.1.1 (2017-03)
[i.6] CEPT/ECC Report 68 (Riga, June 2005): "Compatibility studies in the band 5725-5875 MHz
between Fixed Wireless Access (FWA) systems and other systems".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
antenna assembly: combination of the antenna (integral or dedicated), its coaxial cable and if applicable, its antenna
connector and associated switching components
available channel: channel identified as usable as an Operating Channel
Broadband Fixed Wireless Access (BFWA): operation of fixed Point to Point or fixed Point to Multipoint wireless
devices or systems used to connect fixed locations
burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which
no intentional transmission is made
dedicated antenna: antenna external to the equipment, using an antenna connector with a cable or a wave-guide
NOTE: The antenna has been designed or developed for one or more specific types of equipment. It is the
combination of dedicated antenna and radio equipment that is expected to be compliant with the
regulations.
environmental profile: declared range of environmental conditions under which equipment within the scope of the
present document is required to be compliant
in-service monitoring: mechanism to check a channel in use by the device for the presence of a radar signal with a
level above the Interference Detection Threshold
integral antenna: antenna designed as a fixed part of the equipment, without the use of an external connector and as
such which cannot be disconnected from the equipment by a user with the intend to connect another antenna
NOTE 1: An in
...
Draft ETSI EN 302 502 V2.0.8 (2016-12)
HARMONISED EUROPEAN STANDARD
Wireless Access Systems (WAS);
5,8 GHz fixed broadband data transmitting systems;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 502 V2.0.8 (2016-12)
Reference
REN/BRAN-0060021
Keywords
access, broadband, digital, fixed networks,
harmonised standard, multipoint
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 502 V2.0.8 (2016-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specification . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Designation of centre frequencies and frequency error . 10
4.2.1.1 Definition . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Transmitter RF output power, EIRP and EIRP spectral density . 10
4.2.2.1 Definition . 10
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions . 11
4.2.3.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 11
4.2.3.1.1 Definition. 11
4.2.3.1.2 Limits . 11
4.2.3.1.3 Conformance . 11
4.2.3.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 11
4.2.3.2.1 Definition. 11
4.2.3.2.2 Limits . 12
4.2.3.2.3 Conformance . 12
4.2.4 Transmitter Power Control (TPC) . 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 12
4.2.4.3 Conformance . 12
4.2.5 Receiver spurious emissions . 13
4.2.5.1 Definition . 13
4.2.5.2 Limit . 13
4.2.5.3 Conformance . 13
4.2.6 Dynamic Frequency Selection (DFS) . 13
4.2.6.1 General Requirements . 13
4.2.6.2 DFS Technical requirements specifications . 13
4.2.6.2.1 Channel availability check and channel revalidation period . 13
4.2.6.2.2 In-Service Monitoring . 14
4.2.6.2.3 Channel Shutdown. 14
4.2.6.2.4 Non-Occupancy Period . 15
4.2.7 Receiver Blocking . 15
4.2.7.1 Applicability. 15
4.2.7.2 Definition . 15
4.2.7.3 Performance Criteria . 15
4.2.7.4 Limits . 16
4.2.7.5 Conformance . 16
4.2.8 User Access Restrictions . 16
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 502 V2.0.8 (2016-12)
4.2.8.1 Definition . 16
4.2.8.2 Requirement . 16
5 Testing for compliance with technical requirements . 17
5.1 Environmental conditions for testing . 17
5.1.1 Introduction. 17
5.1.2 Environmental specifications . 17
5.2 Interpretation of the measurement results . 17
5.3 Definition of other test conditions . 18
5.3.1 Test sequences and Traffic load . 18
5.3.1.1 General test transmission sequences . 18
5.3.1.2 Test transmission sequences for DFS tests . 18
5.3.2 Test frequencies . 18
5.3.3 Presentation of Equipment . 18
5.3.3.1 Integrated and Dedicated antennas . 18
5.4 Radio test suites . 19
5.4.1 Product information . 19
5.4.2 Frequency error . 19
5.4.2.1 Test conditions . 19
5.4.2.2 Test methods . 19
5.4.2.2.1 Conducted measurement. 19
5.4.2.2.2 Radiated measurement . 20
5.4.3 Transmitter RF Output Power, EIRP, TPC and EIRP Spectral Density . 20
5.4.3.1 Test conditions . 20
5.4.3.2 Test method . 20
5.4.3.2.1 Conducted measurement. 20
5.4.3.2.2 Radiated measurement . 23
5.4.4 Transmitter unwanted emissions . 23
5.4.4.1 Transmitter unwanted emissions outside the 5 725 MHz to 5 875 MHz band . 23
5.4.4.1.1 Test conditions . 23
5.4.4.1.2 Test method . 23
5.4.4.2 Transmitter unwanted emissions within the 5 725 MHz to 5 875 MHz band . 24
5.4.4.2.1 Test conditions . 24
5.4.4.2.2 Test method . 24
5.4.5 Receiver spurious emissions . 25
5.4.5.1 Test conditions . 25
5.4.5.2 Test method . 25
5.4.5.2.1 Conducted tests . 25
5.4.5.2.2 Radiated tests . 26
5.4.6 Dynamic Frequency Selection (DFS) . 26
5.4.6.1 Test conditions . 26
5.4.6.1.1 Introduction . 26
5.4.6.1.2 Selection of Radar Test Signals . 26
5.4.6.1.3 Test Set-Up . 26
5.4.6.2 Test Method . 27
5.4.6.2.1 Conducted measurement. 27
5.4.6.2.2 Radiated measurement . 31
5.4.7 Receiver Blocking . 32
5.4.7.1 Test conditions . 32
5.4.7.2 Test Method . 32
5.4.7.2.1 Conducted measurements . 32
5.4.7.2.2 Radiated measurements . 33
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 34
Annex B (normative): Test sites and arrangements for radiated measurements . 35
B.1 Test sites . 35
B.1.1 Open air test sites . 35
B.1.2 Anechoic chamber . 36
B.1.2.1 General . 36
B.1.2.2 Description . 36
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 502 V2.0.8 (2016-12)
B.1.2.3 Influence of parasitic reflections . 36
B.1.2.4 Calibration and mode of use . 37
B.2 Test antenna . 38
B.3 Substitution antenna . 39
Annex C (normative): General description of measurement . 40
C.1 Conducted measurements . 40
C.2 Radiated measurements . 40
C.3 Substitution measurement . 41
Annex D (normative): Dynamic Frequency Selection (DFS) parameters . 42
Annex E (informative): Bibliography . 45
Annex F (informative): Change History . 46
History . 47
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 502 V2.0.8 (2016-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document covers 5,8 GHz high performance Broadband Fixed Wireless Access systems (BFWA) including
equipment which is used in wireless local area networks. Such networks provide high speed data communications in
between devices connected to the wireless infrastructure.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 502 V2.0.8 (2016-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for Fixed Broadband Data
Transmitting Systems intended to operate in the 5,8 GHz band (5 725 MHz to 5 875 MHz). The present document is
equally applicable to systems utilizing integral or dedicated antennas.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.3] ETSI EN 300 019-1-0 (V2.1.2) (09-2003): "Environmental Engineering (EE); Environmental
conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of
environmental conditions; Introduction".
[i.4] ETSI TR 100 028-1 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 1".
[i.5] ETSI TR 100 028-2 (V1.4.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics;
Part 2".
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 502 V2.0.8 (2016-12)
[i.6] CEPT/ECC Report 68 (Riga, June 2005): "Compatibility studies in the band 5725-5875 MHz
between Fixed Wireless Access (FWA) systems and other systems".
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
antenna assembly: combination of the antenna (integral or dedicated), its coaxial cable and if applicable, its antenna
connector and associated switching components
available channel: channel identified as usable as an Operating Channel
Broadband Fixed Wireless Access (BFWA): operation of fixed Point to Point or fixed Point to Multipoint wireless
devices or systems used to connect fixed locations
burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which
no intentional transmission is made
dedicated antenna: antenna external to the equipment, using an antenna connector with a cable or a wave-guide
NOTE: The antenna has been designed or developed for one or more specific types of equipment. It is the
combination of dedicated antenna and radio equipment that is expected to be compliant with the
regulations.
environmental profile: declared range of environmental conditions under which equipment within the scope of the
present document is required to be compliant
in-service monitoring: mechanism to check a channel in use by the device for the presence of a radar signal with a
level above the Interference Detection Threshold
integral antenna: antenna designed as a fixed part of the equipment, without the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.