SIST EN ISO 1403:2009
(Main)Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:2005)
Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:2005)
This International Standard specifies the requirements for three types of general-purpose textile-reinforced rubber water hose with an operating range of - 25 °C to + 70 °C, and a maximum working pressure of up to 2,5 MPa. These hoses are not intended to be used for conveyance of potable (drinking) water, for washing-machine inlets, as firefighting hoses, for special agricultural machines or as collapsible water hoses. T hese hoses may be used with additives which lower the freezing point of water.
Gummischläuche mit Textileinlage für allgemeine Anwendungen mit Wasser - Anforderung (ISO 1403:2005)
In dieser Internationalen Norm werden die Anforderungen an drei Typen von Gummischläuchen mit Textileinlage für allgemeine Anwendungen mit Wasser in einem Betriebstemperatur Bereich von 25 °C bis 70 °C und bei einem maximalen Arbeitsdruck bis zu 25 bar festgelegt. )
Diese Schläuche sind nicht vorgesehen für Anwendungen zur Förderung von Trinkwasser, den Zulauf an Waschmaschinen, als Feuerwehrschläuche, für spezielle Landwirtschaftsmaschinen und als faltbare Schläuche.
Die hier beschriebenen Schläuche dürfen angewendet werden, wenn das Wasser Zusätze zur Gefrierpunkts-erniedrigung enthält.
Tuyaux en caoutchouc à armature textile d'usage général pour l'eau - Spécifications (ISO 1403:2005)
L'ISO 1403:2005 spécifie les exigences pour trois types de tuyaux en caoutchouc à armature textile d'usage général pour l'eau, sur une plage de températures de service de -25 °C à +70 °C et pour une pression maximale de service jusqu'à 25 bar.
Ces tuyaux ne sont pas destinés au transport d'eau potable, au raccordement de machine à laver, aux machines agricoles spéciales et ne sont pas destinés à être utilisés comme tuyaux d'arrosage souple ou comme tuyaux d'incendie.
Ces tuyaux peuvent être utilisés avec des additifs abaissant la température de congélation de l'eau.
S tekstilom ojačene gumene cevi za splošno namensko uporabo vode - Specifikacija (ISO 1403:2005)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Tuyaux en caoutchouc à armature textile d'usage général pour l'eau - Spécifications (ISO 1403:2005)Rubber hoses, textile-reinforced, for general-purpose water applications - Specification (ISO 1403:2005)23.040.70Gumene cevi in armatureHoses and hose assembliesICS:Ta slovenski standard je istoveten z:EN ISO 1403:2008SIST EN ISO 1403:2009en,fr01-maj-2009SIST EN ISO 1403:2009SLOVENSKI
STANDARDSIST EN ISO 1403:20001DGRPHãþD
SIST EN ISO 1403:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 1403November 2008ICS 23.040.70Supersedes EN ISO 1403:1997
English VersionRubber hoses, textile-reinforced, for general-purpose waterapplications - Specification (ISO 1403:2005)Tuyaux en caoutchouc à armature textile d'usage généralpour l'eau - Spécifications (ISO 1403:2005)This European Standard was approved by CEN on 29 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 1403:2008: ESIST EN ISO 1403:2009
EN ISO 1403:2008 (E) 2 Contents Page Foreword.3
SIST EN ISO 1403:2009
EN ISO 1403:2008 (E) 3 Foreword The text of ISO 1403:2005 has been prepared by Technical Committee ISO/TC 45 “Rubber and rubber products” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 1403:2008 by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1403:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 1403:2005 has been approved by CEN as a EN ISO 1403:2008 without any modification.
SIST EN ISO 1403:2009
SIST EN ISO 1403:2009
Reference numberISO 1403:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO1403Fourth edition2005-02-15Rubber hoses, textile-reinforced, for general-purpose water applications — Specification Tuyaux en caoutchouc à armature textile d'usage général pour l'eau — Spécifications
SIST EN ISO 1403:2009
ISO 1403:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2005 – All rights reserved
SIST EN ISO 1403:2009
ISO 1403:2005(E) © ISO 2005 – All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.2 4 Classification.2 5 Materials and construction.2 6 Dimensions.2 6.1 Internal diameters and tolerances.2 6.2 Concentricity.2 6.3 Tolerance on length.2 6.4 Minimum thickness of lining and cover.2 7 Physical properties.3 7.1 Rubber compounds.3 7.2 Finished hose.4 8 Marking.4
SIST EN ISO 1403:2009
ISO 1403:2005(E) iv © ISO 2005 – All rights reserved Fore
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.