iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 917:1999

(Main)

Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness

Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness

This standard specifies test methods for the resistance to internal pressure (method A) and the leaktightness (method B) of thermoplastics valves. This standard is applicable to thermoplastics valves intended for the transport of fluids.

Kunststoff-Rohrleitungssysteme - Armaturen aus Thermoplasten - Prüfverfahren für die Widerstandsfähigkeit gegen Innendruck und die Dichtheit

Diese Norm legt Prüfverfahren für den Widerstand gegen Innendruck (Verfahren A) und die Dichtheit (Verfahren B) von Armaturen aus Thermoplasten fest. Diese Norm gilt für Armaturen aus Thermoplasten, die für den Transport von Fluiden vorgesehen sind.

Systemes de canalisations en plastique - Robinets thermoplastiques - Méthodes d'essai de la résistance a la pression interne et de l'étanchéité

Cette norme spécifie des méthodes d'essai pour déterminer la résistance a la pression interne (méthode A) et l'étanchéité (méthode B) des robinets thermoplastiques. Cette norme s'applique aux robinets thermoplastiques utilisés pour le transport de fluides.

Cevni sistemi iz polimernih materialov - Ventili iz plastomernih materialov - Metode za preskus odpornosti proti notranjemu tlaku in neprepustnosti

General Information

Status
Published
Publication Date
30-Jun-1999
ICS
23.060.01 - Valves in general
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-1999
Due Date
01-Jul-1999
Completion Date
01-Jul-1999
Directive
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
EN 917:1997 - Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal pressure and leaktightness

Buy Standard

EN 917:1999EN 917:1999
PreviousNext
Standard
EN 917:1999
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 917:1999
01-julij-1999
Cevni sistemi iz polimernih materialov - Ventili iz plastomernih materialov - Metode
za preskus odpornosti proti notranjemu tlaku in neprepustnosti
Plastics piping systems - Thermoplastics valves - Test methods for resistance to internal
pressure and leaktightness
Kunststoff-Rohrleitungssysteme - Armaturen aus Thermoplasten - Prüfverfahren für die
Widerstandsfähigkeit gegen Innendruck und die Dichtheit
Systemes de canalisations en plastique - Robinets thermoplastiques - Méthodes d'essai
de la résistance a la pression interne et de l'étanchéité
Ta slovenski standard je istoveten z: EN 917:1997
ICS:
23.060.01 Ventili na splošno Valves in general
SIST EN 917:1999 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 917:1999

---------------------- Page: 2 ----
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12201-4:2012(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves
EN 12201-4:2012

This Part of EN 12201 specifies the characteristics of valves or valve bodies made from polyethylene (PE) intended for the conveyance of water intended for human consumption, including raw water prior to treatment.
It also specifies the test parameters for the test methods referred to in this standard.
NOTE 1   Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to prEN 12201 when they have relevant PE connection ends for butt fusion or electrofusion (see prEN 12201-3).
In conjunction with other Parts of prEN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)  a maximum operating pressure, MOP, up to and including 25 bar;
b)  an operating temperature of 20 °C as reference temperature.
NOTE 2   For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see annex A of prEN 12201-1:1999.
prEN 12201 covers a range of maximum operating pressures and gives requirements concerning colours and additives.
NOTE 3   It is the responsibility of the purchaser to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn £ 225 mm.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1452-4:2010(Main)
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009)
EN ISO 1452-4:2009

This part of ISO 1452 specifies the characteristics of valves made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to in this part of ISO 1452. In conjunction with ISO 1452-1, ISO 1452-2, ISO 1452-3 and ISO 1452-5 it is applicable to PVC-U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following: a) water mains and services buried in ground; b) conveyance of water above ground for both outside and inside buildings; c) buried and above-ground drainage and sewerage under pressure. It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 °C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. This part of ISO 1452 is also applicable to valves for the conveyance of water and waste water up to and including 45 °C. For temperatures between 25 °C and 45 °C, Figure A.1 of ISO 1452-2:2009 applies. This part of ISO 1452 is also applicable to valves for the conveyance of water and waste water up to and including 45 °C. For temperatures between 25 °C and 45 °C, Figure A.1 of ISO 1452-2:2009 applies. This part of ISO 1452 is applicable to valves of the following types: - valves for solvent cementing; - valves for elastomeric ring seal joints; - valves for flanged joints.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 12201-4:2021(Main)
Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves for water supply systems
FprEN 12201-4

This document specifies the characteristics of valves or valve bodies made from polyethylene (PE) for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PE pipes or fittings conforming to prEN 12201 2 and prEN 12201 3 respectively.
Valves made from materials other than PE, designed for the supply of water, drainage and sewerage under pressure conforming to the relevant standards can be used in PE piping systems according to EN 12201, provided that they have PE connections for butt fusion or electrofusion ends, including integrated material transition joints, conforming to prEN 12201 3.
NOTE 1   For valves or valve bodies intended for drainage and sewerage under pressure, additional specifications/tests could be necessary according to the requirements of the purchaser, especially for the chemical resistance of the components in contact with the fluids and functioning characteristics.
NOTE 2   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment attention is drawn to 5.4. Components manufactured for water for other purposes are possibly not suitable for water supply for human consumption.
It also specifies the test parameters for the test methods referred to in this document.
NOTE 3   Valves made from material other than polyethylene (PE) designed for the supply of water intended for human consumption to a relevant standard(s) can be used in PE piping systems conforming to EN 12201 when they have relevant PE connection for butt fusion or electrofusion ends (see prEN 12201 3:2021).
In conjunction with Parts 1, 2, 3 and 5 of EN 12201 it is applicable to PE valves, their joints and to joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar );
b)   an operating temperature of 20 °C as a reference temperature;
c)   buried in the ground;
d)   sea outfalls;
e)   laid in water;
f)   above ground, including pipes suspended below bridges.
NOTE 4   For applications operating at constant temperature greater than 20 °C and up to 40 °C, see prEN 12201 1:2021, Annex A.
EN 12201 covers a range of allowable operating pressures and gives requirements concerning colours and additives.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
This Part of EN 12201 covers valves for pipes with a nominal outside diameter dn ≤ 400 mm.

  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5117:2023(Main)
Automatic steam traps - Production and performance characteristic tests (ISO 5117:2023)
EN ISO 5117:2023

This document specifies the production and performance relevant test requirements for automatic steam traps used for condensate removal/recovery services for optimized utilization of energy, in refinery, power generation or other general applications where steam is used as a medium of heat transfer.
The tests can be classified as production tests and performance characteristic tests and can be conducted to ensure the correct functioning of a steam trap or to evaluate the performance of a particular design. This document specifies the tests performed relative to each one of these two categories and briefly describes the corresponding test methods.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17821:2023(Main)
Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
EN 17821:2023

This document specifies general construction, performance and material requirements for the tapware FRT, PN 10. The application in the drinking water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
The conditions of use are according to the following Table 1:
[Table 1 - Conditions of use]
[Figure 1 - The different areas of FRT]

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 5209:2023(Main)
General purpose industrial valves - Marking
ISO 5209:2019

This document specifies the requirements for the mandatory and optional markings of general purpose industrial valves. It defines the method of applying the markings, on the body, on a flange, on an identification plate or any other location.
This document is considered in conjunction with the specified requirements of the valve product standards or valve performance standards.
The marking requirements for plastic valves are not within the scope of this document.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    6 pages
    English language
    sale 15% off
SIST
SIST EN ISO 10497:2023(Main)
Testing of valves - Fire type-testing requirements (ISO 10497:2022)
EN ISO 10497:2022

This document specifies fire type-testing requirements and a fire type-test method for soft- and metalseated isolation valves with one or more obturators. It is not applicable to the testing requirements for
valve actuators other than manually operated gearboxes or similar mechanisms when these form part
of the normal valve assembly. Other types of valve actuators (e.g. electrical, pneumatic or hydraulic)
can need special protection to operate in the environment considered in this valve test, and the fire
testing of such actuators is outside the scope of this document.
This document specifies the measurement and assessment criteria for:
a) through-seat leakage;
b) external leakage;
c) cavity overpressure relief of double-seated valves;
d) operability.
This document specifies the rules whereby the fire-type testing qualification for a valve can be extended
to untested sizes, pressure ratings and materials of construction of the same basic design type.
Fire test reports of valves tested according to previous editions of this document are acceptable when
submitted together with the full and compliant fire test report as per 6.7 of the edition under which it
was tested. Any data missing as required from 6.7 within the fire test report are accepted or rejected at
the purchaser’s discretion.
NOTE For the purposes of this document, the terms “fire type-test” and “fire test” are synonymous.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 23632:2022(Main)
Industrial valves - Design validation-testing of valves (ISO 23632:2021)
EN ISO 23632:2022

This document specifies requirements and acceptance criteria for type testing, in compliance with design conditions, of metallic butterfly and ball valves used for isolating services for all industrial applications, and serves to validate the product design over 205 cycles.
This document excludes testing for safety devices, control valves, thermoplastics valves, and valves for water supply for human consumption and sewage (e.g. the EN 1074 series).
This document defines the procedure for extending the qualification of the tested valve to untested sizes and pressure designations of the same product range.
The purpose of this type test is to validate the seat performance within manufacturer given pressure/temperature rating, provided by the manufacturer’s technical documentation of the product. This type test verifies torque requirements and the maximum allowable stem torque (MAST), as given in the manufacturer's technical documentation. This type test validates the durability of seat performance and operating torque through mechanical and thermal cycles.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 22434:2022(Main)
Gas cylinders - Inspection and maintenance of valves (ISO 22434:2022)
EN ISO 22434:2022

This document specifies requirements for the inspection and maintenance of valves [including ball
valves and valves with integrated pressure regulator (VIPRs)] for:
a) refillable transportable gas cylinders;
b) cylinder bundles;
c) pressure drums and tubes;
which convey compressed, liquefied or dissolved gases.
This document does not apply to valves for liquefied petroleum gas (LPG).
NOTE Where there is no risk of ambiguity, gas cylinders, cylinder bundles, pressure drums and tubes are
addressed with the collective term “gas cylinders” within this document.
This document is applicable to valves reused at the time of the periodic inspection of gas cylinders,
cylinder bundles, pressure drums and tubes, and can be applied at any other time, e.g. at a change of gas
service (see ISO 11621).
This document does not apply to the routine inspection of valves, e.g. carried out at the time of a gas
cylinder filling.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1491:2022(Main)
Building valves - Expansion valves - Tests and requirements
EN 1491:2022

This document specifies dimensions, materials and performance requirements (including methods of test) for expansion valves, of nominal sizes from DN 15 to DN 32, having working pressures ) from 0,1 MPa (l bar) to 1,0 MPa (10 bar).
Expansion valves are intended for fitting to the cold potable water supply of storage water heaters, having a maximum distribution temperature of 95 °C, for all energy sources.
Expansion valves do not control the temperature and alone do not constitute the protection required for storage water heaters. Expansion valves limit pressure, in the water heaters to what they are fitted, that is produced by thermal expansion of the water.
NOTE   The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day