SIST EN 15698-2:2025
(Main)District heating pipes - Bonded twin pipe systems for directly buried hot water networks - Part 2: Factory made fitting and valve assemblies of steel service pipes, polyurethane thermal insulation and a casing of polyethylene
District heating pipes - Bonded twin pipe systems for directly buried hot water networks - Part 2: Factory made fitting and valve assemblies of steel service pipes, polyurethane thermal insulation and a casing of polyethylene
This document specifies requirements and test methods for fitting and steel valve assemblies of factory made thermally insulated bonded twin pipe assemblies for hot water networks in accordance with EN 13941-1, comprising two steel service pipes, in most cases steel fittings and/or steel valves, steel components, polyurethane (PUR) foam thermal insulation and one casing of polyethylene.
NOTE Steel components can be e.g. fixing bars.
The twin pipe assembly can also include the following additional elements: measuring wires, spacers and diffusion barriers.
This document covers the following assemblies:
- fittings: bends, T-pieces and reducers;
- valves for main line.
This document applies to fitting assemblies with an internal pressure of at least 1,6 MPa and steel valve assemblies with a maximum internal pressure of 2,5 MPa.
Fernwärmerohre - Doppelrohr-Verbundsysteme für direkt erdverlegte Fernwärmenetze - Teil 2: Werkmäßig gefertigtes Verbundformstück und vorgedämmte Absperrarmatur, bestehend aus Stahl-Mediumrohr, einer Wärmedämmung aus Polyurethan und einer Ummantelung aus Polyethylen
Dieses Dokument legt Anforderungen und Prüfverfahren für Verbundformstücke und Stahlarmaturenbaugruppen von werkmäßig gedämmten Doppelverbundrohrbaugruppen für Fernwärmenetze in Übereinstimmung mit EN 13941 1 fest, die aus zwei Stahl-Mediumrohren, in den meisten Fällen Stahl-Formstücken und/oder Stahl-Armaturen, Bauteilen aus Stahl, einer Schaumstoffwärmedämmung aus Polyurethan (PUR) und genau einer Ummantelung aus Polyethylen bestehen.
ANMERKUNG Bauteile aus Stahl können z. B. Fixierungsplatten sein.
Die Doppelrohrbaugruppe kann darüber hinaus die folgenden zusätzlichen Bauteile umfassen: Messdrähte, Abstandhalter und Diffusionsbarrieren.
Dieses Dokument behandelt die folgenden Baugruppen:
- Formstücke: Bögen, T Stücke und Reduzierstücke;
- Armaturen für die Hauptleitung.
Dieses Dokument gilt für Verbundformstücke mit einem Innendruck von mindestens von 1,6 MPa und für Stahl-Armaturenbaugruppen mit einem maximalen Innendruck von 2,5 MPa.
Tuyaux de chauffage urbain - Systèmes bloqués de bitubes pour les réseaux d'eau chaude enterrés directement - Partie 2: Assemblages de raccords et d'appareils de robinetterie manufacturés pour tube de service en acier, isolation thermique en polyuréthane et tube de protection en polyéthylène
Le présent document définit les exigences et les méthodes d’essai applicables au raccord et aux appareils de robinetterie en acier d’assemblages de bitubes manufacturés isolés thermiquement pour réseaux d’eau chaude conformément à l’EN 13941-1, comprenant deux tubes de service en acier, dans la plupart des cas des raccords en acier et/ou des appareils de robinetterie en acier, des composants en acier, une isolation thermique en mousse de polyuréthane (PUR) et une protection en polyéthylène.
NOTE Les composants en acier peuvent être, par exemple, des barres de fixation.
L’assemblage de bitubes peut également comprendre les éléments supplémentaires suivants : des câbles de mesure, des entretoises et les barrières anti-diffusion.
Le présent document couvre les assemblages suivants :
- les raccords : les coudes, les coudes en T et les réductions ;
- les appareils de robinetterie pour la ligne principale.
Le présent document s’applique aux assemblages de raccords ayant une pression interne d'au moins 1,6 MPa et aux assemblages d’appareils de robinetterie en acier ayant une pression interne maximale de 2,5 MPa.
Cevi za daljinsko ogrevanje - Poviti dvocevni sistemi za neposredno vkopana vročevodna omrežja - 2. del: Tovarniško izdelan sestav fitingov in ventilov iz jeklene cevi, poliuretanske toplotne izolacije in zunanjega polietilenskega plašča
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2025
Cevi za daljinsko ogrevanje - Poviti dvocevni sistemi za neposredno vkopana
vročevodna omrežja - 2. del: Tovarniško izdelan sestav fitingov in ventilov iz
jeklene cevi, poliuretanske toplotne izolacije in zunanjega polietilenskega plašča
District heating pipes - Bonded twin pipe systems for directly buried hot water networks -
Part 2: Factory made fitting and valve assemblies of steel service pipes, polyurethane
thermal insulation and a casing of polyethylene
Fernwärmerohre - Doppelrohr-Verbundsysteme für direkt erdverlegte Fernwärmenetze -
Teil 2: Werkmäßig gefertigtes Verbundformstück und vorgedämmte Absperrarmatur,
bestehend aus Stahl-Mediumrohr, einer Wärmedämmung aus Polyurethan und einer
Ummantelung aus Polyethylen
Tuyaux de chauffage urbain - Systèmes bloqués de bitubes pour les réseaux d'eau
chaude enterrés directement - Partie 2: Assemblages de raccords et d'appareils de
robinetterie manufacturés pour tube de service en acier, isolation thermique en
polyuréthane et tube de protection en polyéthylène
Ta slovenski standard je istoveten z: EN 15698-2:2025
ICS:
23.040.07 Cevovodi za daljinsko Pipeline and its parts for
ogrevanje in njihovi deli district heat
23.040.10 Železne in jeklene cevi Iron and steel pipes
91.140.10 Sistemi centralnega Central heating systems
ogrevanja
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 15698-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2025
EUROPÄISCHE NORM
ICS 23.040.07 Supersedes EN 15698-2:2019
English Version
District heating pipes - Bonded twin pipe systems for
directly buried hot water networks - Part 2: Factory made
fitting and valve assemblies of steel service pipes,
polyurethane thermal insulation and one casing of
polyethylene
Tuyaux de chauffage urbain - Systèmes bloqués de Fernwärmerohre - Doppelrohr-Verbundsysteme für
bitubes pour les réseaux d'eau chaude enterrés direkt erdverlegte Fernwärmenetze - Teil 2:
directement - Partie 2: Assemblages de raccords et Werkmäßig gefertigte Formstück- und
d'appareils de robinetterie manufacturés pour tubes de Armaturbaueinheiten, bestehend aus Stahl-
service en acier, isolation thermique en polyuréthane Mediumrohr, einer Wärmedämmung aus Polyurethan
et tube de protection en polyéthylène und einer Ummantelung aus Polyethylen
This European Standard was approved by CEN on 27 January 2025.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15698-2:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Requirements . 7
4.1 General . 7
4.2 Steel parts . 7
4.2.1 Specification . 7
4.2.2 Valves. 7
4.2.3 Diameter and wall thickness . 7
4.2.4 Surface condition . 7
4.3 Welding of steel parts . 8
4.3.1 Welding of steel service pipes and elements . 8
4.3.2 Welding of fixing bars . 8
4.3.3 Placing of the fixing bars . 8
4.4 Casing . 8
4.5 Polyurethane foam thermal insulation . 8
4.6 Fitting and valve assemblies . 8
4.6.1 General . 8
4.6.2 Thermal insulation series . 8
4.6.3 End alignment of flow and return steel service pipes . 8
4.6.4 Distance between flow and return steel service pipes . 9
4.6.5 End of fitting and valve assemblies. 9
4.6.6 Polyethylene welding . 10
4.6.7 End of stem construction . 10
4.6.8 Tolerances of the main fitting and valve dimensions . 10
4.7 Expected thermal life and long-term temperature resistance . 10
4.8 Thermal conductivity . 10
4.9 Surface conditions at delivery . 10
4.10 Measuring wires for surveillance systems . 10
4.11 Resistance of the valves to axial forces and bending moments. 10
4.12 Installation, operation and maintenance . 10
5 Test methods . 11
6 Marking . 11
6.1 General . 11
6.2 Steel service pipe . 11
6.3 Fitting . 11
6.4 Casing . 11
6.5 Fitting assembly . 11
6.6 Valves and valve assembly . 11
6.7 Service valves and service valve assemblies . 11
Annex A (informative) Guidelines for inspection and testing . 12
Annex B (informative) Waste treatment and recycling . 14
Annex C (informative) Examples of twin pipe fitting assemblies . 15
Bibliography . 18
European foreword
This document (EN 15698-2:2025) has been prepared by Technical Committee CEN/TC 107
“Prefabricated district heating and district cooling pipe system”, the secretariat of which is held by DS.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2025, and conflicting national standards shall
be withdrawn at the latest by September 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 15698-2:2019.
— alignment with the structure of EN 253;
— in alignment with the other standards of CEN/TC 107, explanatory information has been included in
Annex B.
The EN 15698 series, under the title District heating pipes — Bonded twin pipe systems for directly buried
hot water networks, is currently composed of the following parts:
— Part 1: Factory made twin pipe assembly of steel service pipes, polyurethane thermal insulation and one
casing of polyethylene;
— Part 2: Factory made fitting and valve assemblies of steel service pipes, polyurethane thermal insulation
and one casing of polyethylene (this document).
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
Other standards from CEN/TC 107 are:
— EN 253, District heating pipes — Bonded single pipe systems for directly buried hot water networks —
Factory made pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of
polyethylene
— EN 448, District heating pipes — Bonded single pipe systems for directly buried hot water networks —
Factory made fitting assemblies of steel service pipes, polyurethane thermal insulation and a casing of
polyethylene
— EN 488-1, District heating pipes — Bonded single pipe systems for directly buried hot water networks
— Part 1: Factory made steel shut-off valve assembly for steel service pipes, polyurethane thermal
insulation and a casing of polyethylene;
— EN 488-2, District heating and district cooling pipes — Bonded pipe systems for directly buried hot and
cold water networks — Part 2: Factory made steel valve assembly for steel service pipes, polyurethane
thermal insulation and a casing of polyethylene
— EN 489-1, District heating pipes — Bonded single and twin pipe systems for buried hot water
networks — Par
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.