iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST ISO 12488-1:2012/Cor 1:2012

(Corrigendum)

Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General

Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General

This part of ISO 12488 specifies tolerances for construction assemblies and operational conditions of cranes and associated crane tracks as defined in ISO 4306-1. The purpose of the requirements in this part of ISO 12488 is to promote safe operation and achievement of the expected life of components by the elimination of excessive load effects due to deviations or misalignments from the normal dimensions of the structure. Tolerances given are extreme values. The elastic deformations due to load effects are outside the scope of this part of ISO 12488. These will need to be taken into account at the design stage using other criteria to achieve the intended operation and performance. Specific values for particular crane types are given in other parts of ISO 12488.

Appareils de levage à charge suspendue - Tolérances des roues et des voies de roulement et de déplacement - Partie 1: Généralités

Žerjavi - Tolerance za kolesa, gibanje in vozne proge - 1. del: Splošno - Popravek

Ta del standarda ISO 12488 določa tolerance za konstrukcijske sestave in obratovalne pogoje žerjavov in povezanih prog žerjavov iz standarda ISO 4306-1. Namen zahtev v tem delu standarda ISO 12488 je spodbujati varno obratovanje in doseganje pričakovane življenjske dobe sestavnih delov z odpravo učinkov prekomernih obremenitev zaradi odstopanj od normalnih mer strukture ali neporavnanosti z njimi. Navedene tolerance so skrajne vrednosti. Elastične deformacije zaradi učinkov obremenitev ne spadajo v področje uporabe tega dela standarda ISO 12488. Deformacije bo treba upoštevati v fazi načrtovanja z uporabo drugih meril, da se dosežeta nameravano obratovanje in učinkovitost. Posebne vrednosti za posamezne vrste žerjavov so navedene v drugih delih standarda ISO 12488.

General Information

Status
Withdrawn
Publication Date
26-Sep-2012
Withdrawal Date
21-Jan-2015
ICS
53.020.20 - Cranes
Technical Committee
DTN - Lift and transport appliances
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-Jan-2015
Due Date
12-Feb-2015
Completion Date
22-Jan-2015
Ref Project
ISO 12488-1:2005/Cor 1:2008 - Cranes — Tolerances for wheels and travel and traversing tracks — Part 1: General — Technical Corrigendum 1

Relations

Corrects
SIST ISO 12488-1:2012 - Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General
Effective Date
01-Oct-2012
Child
SIST ISO 12488-1:2012 - Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General
Effective Date
04-Sep-2008
Replaced By
SIST ISO 12488-1:2015 - Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General
Effective Date
01-Mar-2015
Corrects
SIST ISO 12488-1:2012 - Cranes - Tolerances for wheels and travel and traversing tracks - Part 1: General
Effective Date
06-Jun-2022

Buy Standard

ISO 12488-1:2012/Cor 1:2012ISO 12488-1:2012/Cor 1:2012
PreviousNext
Corrigendum
ISO 12488-1:2012/Cor 1:2012
English language
2 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Žerjavi - Tolerance za kolesa, gibanje in vozne proge - 1. del: Splošno - PopravekAppareils de levage à charge suspendue - Tolérances des roues et des voies de roulement et de déplacement - Partie 1: GénéralitésCranes - Tolerances for wheels and travel and traversing tracks - Part 1: General53.020.20DvigalaCranesICS:Ta slovenski standard je istoveten z:ISO 12488-1:2005/Cor 1:2008SIST ISO 12488-1:2012/Cor 1:2012en01-oktober-2012SIST ISO 12488-1:2012/Cor 1:2012SLOVENSKI
STANDARD



SIST ISO 12488-1:2012/Cor 1:2012



ICS
53.020.20 Ref. No. ISO 12488-1:2005/Cor.1:2008(E)©
ISO 2008 – All rights reserved Published in Switzerland
INTERNATIONAL STANDARD ISO 12488-1:2005 TECHNICAL CORRIGENDUM 1 Published 2008-11-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION •
• ORGANISATION INTERNATIONALE DE NORMALISATION
Cranes — Tolerances for wheels and travel and traversing tracks —
Part 1: General TECHNICAL CORRIGENDUM 1 Appareils de levage à charge suspendue — Tolérances des roues et des voies de roulement et de déplacement —
Partie 1: Généralités RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to International Standard ISO 12488-1:2005 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 8, Jib cranes.
Page 2,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13001-3-6:2018+A1:2021(Main)
Cranes - General design - Part 3-6: Limit states and proof of competence of machinery - Hydraulic cylinders
EN 13001-3-6:2018+A1:2021

This document is to be used together with the other generic parts of EN 13001 series of standards, see Annex E, as well as pertinent crane type product EN standards, and as such they specify general conditions, requirements and methods to, by design and theoretical verification, prevent mechanical hazards of hydraulic cylinders that are part of the load carrying structures of cranes. Hydraulic piping, hoses and connectors used with the cylinders are not within the scope of this document, as well as cylinders made from other material than carbon steel.
NOTE 1   Specific requirements for particular crane types are given in the appropriate European product standards, see Annex E.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use are identified in Annex F. Clauses 4 to 7 of this document provide requirements and methods to reduce or eliminate these risks:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   elastic instability (column buckling).
NOTE 2   EN 13001-3-6 deals only with the limit state method in accordance with EN 13001-1.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13001-3-5:2016+A1:2021(Main)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13001-2:2021(Main)
Crane safety - General design - Part 2: Load actions
EN 13001-2:2021

This document specifies load actions to be used together with the standards EN 13001 1 and EN 13001 3, and as such they specify conditions and requirements on design to prevent mechanical hazards of cranes, and provides a method of verification of those requirements.
NOTE   Specific requirements for particular types of crane are given in the appropriate European Standard for the particular crane type.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clause 4 of this document is necessary to reduce or eliminate the risks associated with the following hazards:
a)   instability of the crane or its parts (tilting);
b)   exceeding the limits of strength (yield, ultimate, fatigue);
c)   elastic instability of the crane or its parts (buckling, bulging);
d)   exceeding temperature limits of material or components;
e)   exceeding the deformation limits.
This document is not applicable to cranes that are manufactured before the date of its publication as EN.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   The supporting pedestal and structures such as columns and boom rests are covered by this standard to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel.
The following characteristics distinguish light offshore cranes from other types of offshore cranes:
-   maximum rated capacity 20 tonnes, maximum load moment 300 tm;
-   limitation for off-board lifting operation Hs = 2,0 m and wind speed 15 m/s (3s gust);
-   maximum number of working cycles class U3 (C ≤ 125.000) according to EN 13001-1.
This document gives requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping or changing the configuration of the crane;
b)   non- fixed load lifting attachments, i.e. any item between the hook and the load;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads due to collisions or earthquakes;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes, floating cranes and motion compensated cranes.
This document is applicable for the lifting of personnel.
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    95 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13586:2021(Main)
Cranes - Access
EN 13586:2020

This European Standard specifies design requirements for non-powered access installed on cranes.
NOTE 1 For other type of access a requirement for information to be supplied is specified.
This European Standard covers access to control stations and all access required for maintenance, certain erection
and dismantling operations (see below) and emergency.
For those cranes which are intended to be erected and dismantled at their places of work, specific requirements for the
access needed during these operations are given in the appropriate European Standards for specific crane types.
NOTE 2 Specific requirements for access on particular types of crane are given in the appropriate European Standard for the
particular crane type.
The dimensions given in this European Standard do not take into account the safety distances related to:
- guarding;
-  relative movement between crane and adjacent structure;
- hazardous surface temperature;
- electrical equipment.
The significant hazards covered by this European Standard are identified in clause 4.
This European Standard is not applicable to cranes which are manufactured before the date of publication by CEN of
this standard.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17076:2021(Main)
Tower cranes - Anti-collision systems - Safety requirements
EN 17076:2020

This European Standard specifies the functional requirements of anti-collision devices and systems installed on self-erecting tower cranes or tower cranes assembled from component parts to avoid the risks of collision between several cranes in use, between a crane in use and fixed obstacles, and over prohibited zones.
It applies to anti-collision devices manufactured after the publication of this standard.
NOTE   For anti-collision systems used to avoid the risk of collision with power lines, additional requirements might be necessary.
This document defines the safety characteristics and requirements of anti-collision devices and systems intended for installation on self-erecting tower cranes or tower cranes assembled from component parts.
In particular:
-   performance level;
-   information to be provided by the sensors installed on the crane;
-   operation, particularly in the event of failure, override and free jib slewing states of a crane;
-   type of communication between devices;
-   information for the crane operator and outside indicator.
It also specifies the requirements for marking the device or the system and the content of the instruction for use.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16851:2017+A1:2021(Main)
Cranes - Light crane systems
EN 16851:2017+A1:2020

This document applies to:
-   light crane systems, either suspended or free-standing systems, where the rated capacity of any single lifting device is 4 t or less;
-   pillar and wall-mounted jib cranes, without an operator's cabin, whose rated capacity is 10 t or less and whose overturning load moment is 500 kNm or less.
NOTE   For illustration of crane types, see Annex B.
This document is not applicable to cranes covered by another product specific crane standard, e.g. EN 15011:2011+A1:2014 or EN 14985:2012.
This document is applicable to cranes and crane systems, whose structures are made of steel or aluminium, excluding aluminium structures containing welded joints.
This document gives requirements for all significant hazards, hazardous situations and events relevant to cranes, when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
The specific hazards due to potentially explosive atmospheres, ionizing radiation, operation in electro-magnetic fields beyond the range of EN 61000 6 2:2016 and operation in pharmacy or food industry are not covered by this document.
This document does not cover hazards related to the lifting of persons.
This document is applicable to cranes, which are manufactured after the date of its publication by CEN as a European Standard.
This document is not applicable to cranes manufactured before the date of its publication.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15011:2021(Main)
Cranes - Bridge and gantry cranes
EN 15011:2020

This European Standard applies to bridge and gantry cranes able to travel by wheels on rails, runways or roadway surfaces, and to gantry cranes without wheels mounted in a stationary position.
This European Standard specifies requirements for all significant hazards, hazardous situations and events relevant to bridge and gantry cranes when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
This European Standard does not include requirements for the lifting of persons.
The specific hazards due to potentially explosive atmospheres, ionising radiation and operation in electromagnetic fields beyond the range of EN 61000-6-2 are not covered by this European Standard.
This European Standard is applicable to bridge and gantry cranes manufactured after the date of its publication as an EN.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12999:2020(Main)
Cranes - Loader cranes
EN 12999:2020

This document specifies minimum requirements for design, calculation, examinations and tests of hydraulic powered loader cranes and their mountings on vehicles or static foundations.
This document does not apply to loader cranes used on board sea going vessel or to articulated boom system cranes which are designed as total integral parts of special equipment such as forwarders.
The hazards covered by this standard are identified in Clause 4.
This document does not cover hazards related to the lifting of persons.
NOTE   The use of cranes for lifting of persons can be subject to specific national regulations.
This document is not applicable to loader cranes manufactured before the publication of this document. For loader cranes designed before the publication of this document, the new provisions concerning stress calculations are not applicable.

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    103 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST ISO 4305:2015/Amd 1:2020(Amendment)
Mobile cranes - Determination of stability
ISO 4305:2014/Amd 1:2016
  • Standard
    1 page
    English language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Standard
    1 page
    French language
    sale 15% off
  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day