SIST EN 12697-40:2006

Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability

This European Standard describes a method to determine the in-situ relative hydraulic conductivity, at specific locations, of a road surfacing that is designed to be permeable. An estimate of the average value for the surfacing is obtained from the mean value of a number of determinations on each section of road.
The test measures the ability to drain water (drainability) achieved in-situ of a surfacing. As such, it can be used as a compliance check to ensure that a permeable surface course has the required properties when it is laid. The test can also be used subsequently to establish the change of drainage ability with time.
For the test to be valid, the surface of the test area should be clean and free from detritus. Measurements can be made when a road is either wet or dry, but not if it is in a frozen state.

Asphalt - Prüfverfahren für Heißasphalt - Teil 40: In-situ-Durchlässigkeit

Diese Europäische Norm beschreibt ein Verfahren zur Bestimmung der relativen in-situ-Wasserdurchlässig-keit an festgelegten Punkten einer als wasserdurchlässig ausgelegten Deckschicht. Anhand des Mittelwertes einer festgelegten Anzahl von Bestimmungen jedes Abschnitts der betreffenden Straße wird ein Schätzwert für den Durchschnittswert der Deckschicht ermittelt.
Mit dieser Prüfung wird die Drainagefähigkeit der eingebauten Deckschicht (Durchlässigkeit) gemessen. Als solche kann sie als Nachweis verwendet werden, dass eine durchlässige Deckschicht nach dem Einbau die geforderten Eigenschaften hat. Die Prüfung kann auch später durchgeführt werden, um die Änderung der Durchlässigkeit mit der Zeit zu ermitteln.
Damit die Prüfung gültig ist, muss die Oberfläche des Prüfbereiches sauber und frei von losen Bestandteilen sein. Die Messungen können entweder bei nasser oder bei trockener Straße, nicht jedoch bei Frost durchge-führt werden.

Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 40: Drainabilité in situ

La présente Norme européenne décrit une méthode permettant de déterminer la conductivité hydraulique relative in-situ, a certains endroits spécifiques d’un revetement routier conçu pour etre drainant. Une estimation de la valeur moyenne pour le revetement est obtenue a partir de la valeur moyenne d’un certain nombre de déterminations sur chaque section de route.
L’essai sert a mesurer in-situ la capacité a drainer l’eau (drainabilité) d’un revetement. En tant que tel, il peut etre utilisé comme contrôle de conformité afin de garantir qu’une couche de surface drainante a les propriétés requises lors de la mise en oeuvre. L’essai peut également servir ultérieurement a établir les variations de la capacité drainante avec le temps.
Pour que l’essai soit valable, il est recommandé que la surface de la zone d’essai soit propre et exempte de détritus. Les mesurages peuvent etre effectués sur route seche ou mouillée, mais pas sur route gelée.

Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 40. del: Prepustnost vgrajene plasti (in situ)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2006
• Withdrawal Date: 01-Aug-2012
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CES - Roads
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 01-Aug-2012
• Due Date: 24-Aug-2012
• Completion Date: 02-Aug-2012
• Directive: 89/106/EEC - Construction products
• Ref Project: EN 12697-40:2005 - Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability

Relations

• Replaced By: SIST EN 12697-40:2012 - Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability
• Effective Date: 01-Sep-2012
• Replaced By: SIST EN 12697-40:2012 - Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12697-40:2006
01-april-2006
%LWXPHQVNH]PHVL±3UHVNXVQHPHWRGH]DYURþHDVIDOWQH]PHVL±GHO
3UHSXVWQRVWYJUDMHQHSODVWLLQVLWX
Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In situ drainability
Asphalt - Prüfverfahren für Heißasphalt - Teil 40: In-situ-Durchlässigkeit
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie
40: Drainabilité in situ
Ta slovenski standard je istoveten z: EN 12697-40:2005
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
SIST EN 12697-40:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12697-40:2006

---------------------- Page: 2 ----------------------

SIST EN 12697-40:2006
EUROPEAN STANDARD
EN 12697-40
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 93.080.20

English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part
40: In situ drainability
Mélanges bitumineux - Méthodes d'essai pour mélange Asphalt - Prüfverfahren für Heißasphalt - Teil 40: In situ-
hydrocarboné à chaud - Partie 40: Drainabilité in situ Durchlässigkeit
This European Standard was approved by CEN on 30 September 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12697-40:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12697-40:2006
EN 12697-40:2005 (E)
Content Page
Foreword .3
1 Scope.6
2 Normative references.6
3 Terms and definitions.6
4 Principle.7
5 Apparatus.7
5.1 Permeameter.7
5.2 Standing board.8
5.3 Stopwatch.9
5.4 Thermometer.9
5.5 Water.9
6 Procedure.9
6.1 Calibration.9
6.2 Locations.9
6.3 Measurement at each location .10
7 Calculation.10
8 Report.11
9 Precision.12
Annex A (normative) Apparatus calibration.13

A.1 Application.13
A.2 Volume calibration.13
A.3 Series resistance time, r.13
A.4 Parallel leakage time.13
Bibliography.15

2

---------------------- Page: 4 ----------------------

SIST EN 12697-40:2006
EN 12697-40:2005 (E)
Foreword
This document (EN 12697-40:2005) has been prepared by Technical Committee CEN/TC 227 “Road
materials”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2006 and conflicting national standards shall be withdrawn at the
latest by January 2008.
This document is one of a series of standards as listed below.
EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content.
EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle size
distribution.
EN 12697-3, Bituminous mixtures —Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary
evaporator.
EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery:
Fractionating column.
EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the
maximum density.
EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density
of bituminous specimens.
EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density
of bituminous specimens by gamma rays.
EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void
characteristics of bituminous specimens.
EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of the
reference density.
EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability.
EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the
affinity between aggregate and bitumen.
EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water
sensitivity of bituminous specimens.
EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measure-
ment.
EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content.
EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the
segregation sensitivity.
EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres.
3

---------------------- Page: 5 ----------------------

SIST EN 12697-40:2006
EN 12697-40:2005 (E)
EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous
asphalt specimen.
EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage.
EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen.
EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or
Marshall specimens.
EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate
specimens.
EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking.
EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the
indirect tensile strength of bituminous specimens.
EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue.
EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test.
EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness.
EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling.
EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for
determining binder content, water content and grading.
EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the
dimensions of a bituminous specimen.
EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation,
impact compactor.
EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation,
gyratory compactor.
EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of
bituminous mixtures by a vibratory compactor.
EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared, by
roller compactor.
EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test.
EN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing.
EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the
thickness of a bituminous pavement.
EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the
adhesivity of binder on precoated chippings for HRA.
EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and
calibration.
EN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition.
4

---------------------- Page: 6 ----------------------

SIST EN 12697-40:2006
EN 12697-40:2005 (E)
EN 12697-40, Bituminous mixtures - Test methods for hot mix asphalt - Part 40: In-situ drainablility
EN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing
fluids.
EN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreign matters
in reclaimed asphalt.
EN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.
5

---------------------- Page: 7 ----------------------

SIST EN 12697-40:2006
EN 12697-40:2005 (E)
1 Scope
This European Standard describes a method to determine the in-situ relative hydraulic conductivity, at specific
locations, of a road surfacing that is designed to be permeable. An estimate of the average value for the
surfacing is obtained from the mean value of a number of determinations on each section of road.
The test measures the ability to drain water (drainability) achieved in-situ of a surfacing. As such, it can be
used as a compliance check to ensure that a permeable surface course has the required properties when it is
laid. The test can also be used subsequently to establish the change of drainage ability with time.
For the test to be valid, the surface of the test
...