Machine tools - Safety - Machining centres

Amendment of Table 2, 5.2, 1.1.6.4 - Mode 3.

Werkzeugmaschinen - Sicherheit - Bearbeitungszentren

Machines-outils - Sécurité - Centres d'usinage

Obdelovalni stroji - Varnost – Obdelovalni centri

General Information

Status
Withdrawn
Publication Date
31-Aug-2006
Withdrawal Date
24-Mar-2009
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
13-Mar-2009
Due Date
05-Apr-2009
Completion Date
25-Mar-2009

RELATIONS

Buy Standard

Amendment
SIST EN 12417:2002/A1:2006
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 12417:2002/A1:2006
01-september-2006
Obdelovalni stroji - Varnost – Obdelovalni centri
Machine tools - Safety - Machining centres
Werkzeugmaschinen - Sicherheit - Bearbeitungszentren
Machines-outils - Sécurité - Centres d'usinage
Ta slovenski standard je istoveten z: EN 12417:2001/A1:2006
ICS:
25.040.10
SIST EN 12417:2002/A1:2006 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 12417:2001/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2006
ICS 25.040.10
English Version
Machine tools - Safety - Machining centres

Machines-outils - Sécurité - Centres d'usinage Werkzeugmaschinen - Sicherheit - Bearbeitungszentren

This amendment A1 modifies the European Standard EN 12417:2001; it was approved by CEN on 3 February 2006.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this

amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such

national standards may be obtained on application to the Central Secretariat or to any CEN member.

This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the

responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,

Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,

Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels

© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12417:2001/A1:2006: E

worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 12417:2001/A1:2006 (E)
Foreword

This European Standard (EN 12417:2001/A1:2006) has been prepared by Technical Committee CEN/TC 143

“Machine tools - Safety”, the secretariat of which is held by SNV.

This Amendment to the European Standard EN 12417:2001 shall be given the status of a national standard,

either by publication of an identical text or by endorsement, at the latest by September 2006, and conflicting

national standards shall be withdrawn at the latest by September 2006.

This European Standard has been prepared under a mandate given to CEN by the European Commission

and the European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this European

Standard.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,

Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

Switzerland and United Kingdom.
---------------------- Page: 3 ----------------------
EN 12417:2001/A1:2006 (E)
Location of the proposed amendments (for EN 12417:2001):
Add in Clause 2:

EN ISO 15641, Milling cutters for high speed machining — Safety requirements (ISO 15641:2001)

Insert the proposed amendment as a replacement and addition into Table 2 of 5.2, 1.1.6.4 – Mode 3.

Hazards Safety requirement and/or protective measure Verification
1 Mechanical 1.1.6.4 Mode 3 - Optional mode for manual intervention under
restricted operating conditions
(continued) When provided, this mode permits use of the machine under manual or
numerical control with work zone guards open and/or protective devices
suspended under the following conditions:

a) This mode shall only be provided when details of the intended application Visual inspection (of

are known and the required skill level of operators shall be defined in the Instruction

instruction handbook (see 7.2 g) of this European Standard). handbook)
b) Single axis and multiple axis vector speeds shall be limited to 5m/min.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.