SIST EN 1646-1:2018
(Main)Leisure accommodation vehicles - Motor caravans - Part 1: Habitation requirements relating to health and safety
Leisure accommodation vehicles - Motor caravans - Part 1: Habitation requirements relating to health and safety
This European Standard specifies requirements intended to ensure the safety and health of persons when they use motor caravans for temporary or seasonal habitation.
It also specifies the corresponding test methods.
Specific requirements of this European Standard apply to motor caravans where the overall length multiplied by the overall width does not exceed 13,5 m2 plan area.
Requirements applicable to road safety are not included in the scope of this European Standard.
This European Standard is applicable exclusively to motor caravans as defined in EN 13878.
Bewohnbare Freizeitfahrzeuge - Motorcaravans - Teil 1: Anforderungen an den Wohnbereich hinsichtlich Gesundheit und Sicherheit
Diese Europäische Norm legt Anforderungen für die Sicherheit und Gesundheit von Personen fest, wenn diese Motorcaravans zeitweilig oder saisonbedingt bewohnen.
Sie legt auch die entsprechenden Prüfverfahren fest.
Bestimmte Anforderungen dieser Europäischen Norm gelten für Motorcaravans, deren Grundfläche, ermittelt durch Multiplikation der Gesamtlänge mit der Gesamtbreite, nicht größer als 13,5 m2 ist.
Anforderungen an die Sicherheit im Straßenverkehr gehören nicht zum Anwendungsbereich dieser Europäischen Norm.
Diese Europäische Norm gilt ausschließlich für Motorcaravans, wie in EN 13878 festgelegt.
Véhicules habitables de loisirs - Autocaravanes - Partie 1 : Exigences d'habitation relatives à la santé et à la sécurité
La présente Norme européenne spécifie les exigences destinées à assurer la sécurité et la santé des personnes lorsque celles-ci utilisent les autocaravanes comme logements temporaires ou saisonniers.
Elle spécifie également les méthodes d’essai correspondantes.
Les exigences spécifiques à la présente Norme européenne s’appliquent aux autocaravanes dont le produit de la longueur hors tout par la largeur hors tout ne dépasse pas 13,5 m2.
Les exigences applicables à la sécurité routière n’entrent pas dans le domaine d’application de la présente Norme européenne.
La présente Norme européenne s’applique exclusivement aux autocaravanes, telles que définies dans l’EN 13878.
Bivalna počitniška vozila - Avtodomi - 1. del: Zdravstvene in varnostne zahteve za bivanje
Ta evropski standard določa zahteve, namenjene za zagotavljanje varnosti in zdravja ljudi med uporabo avtodomov za začasno ali sezonsko bivanje.
Določa tudi ustrezne preskusne metode.
Določene zahteve tega evropskega standarda veljajo za avtodome, katerih zmnožek skupne dolžine in skupne širine ni večji od površine 13,5 m2.
Zahteve za varnost v cestnem prometu ne spadajo na področje uporabe tega standarda.
Ta evropski standard se uporablja samo za avtodome iz standarda EN 13878.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ELYDQMHBewohnbare Freizeitfahrzeuge - Motorcaravans - Teil 1: Anforderungen an den Wohnbereich hinsichtlich Gesundheit und SicherheitVéhicules habitables de loisirs - Autocaravanes - Partie 1 : Exigences d'habitation relatives à la santé et à la sécuritéLeisure accommodation vehicles - Motor caravans - Part 1: Habitation requirements relating to health and safety43.100Osebni avtomobili. Bivalne prikolice in lahke prikolicePassenger cars. Caravans and light trailersICS:Ta slovenski standard je istoveten z:EN 1646-1:2018SIST EN 1646-1:2018en,fr,de01-april-2018SIST EN 1646-1:2018SLOVENSKI
STANDARDSIST EN 1646-1:20121DGRPHãþD
SIST EN 1646-1:2018
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1646-1
February
t r s z ICS
v uä s r r Supersedes EN
s x v xæ sã t r s tEnglish Version
Leisure accommodation vehicles æ Motor caravans æ Part
sã Habitation requirements relating to health and safety Véhicules habitables de loisirs æ Autocaravanes æ Partie
s ã Exigences d 5habitation relatives à la santé et à la sécurité
Bewohnbare Freizeitfahrzeuge æ Motorcaravans æ Teil
sã Anforderungen an den Wohnbereich hinsichtlich Gesundheit und Sicherheit This European Standard was approved by CEN on
x December
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x v xæ sã t r s z ESIST EN 1646-1:2018
EN 1646-1:2018 (E) 2 Contents Page European foreword . 5 Introduction . 6 1 Scope . 7 2 Normative references . 7 3 Terms and definitions . 7 4 Testing . 7 5 Design and construction . 8 5.1 Occupancy . 8 5.2 Entrance steps to living area . 8 5.2.1 Heights . 8 5.2.2 Minimum tread dimensions . 8 5.2.3 Mechanical strength . 8 5.2.4 Slip resistance test . 8 5.3 Doors . 9 5.3.1 Dimensions . 9 5.3.2 Securing doors . 9 5.3.3 Childproof locking systems . 9 5.3.4 Dead-locking systems . 9 5.4 Awning rails . 9 6 Internal equipment . 9 6.1 Bunks . 9 6.1.1 Mattress and/or upholstery . 9 6.1.2 Clearance . 9 6.1.3 Protection against falling out . 10 6.1.4 Mechanical strength . 10 6.1.5 Security of bunks . 10 6.1.6 Access to high level bunks. 11 6.1.7 Protection against entrapment . 11 6.2 Cupboards . 11 6.3 Cooking appliance . 11 7 Drinking water supply, storage and disposal of waste water . 12 7.1 Couplings for drinking water supply . 12 7.2 Drinking water . 12 7.2.1 Tanks . 12 7.2.2 Materials . 12 7.2.3 Marking . 12 7.3 Waste water disposal tank . 12 7.4 Toilet waste disposal . 12 7.4.1 Discharge systems . 12 7.4.2 Outlets and couplings from toilet holding tanks . 12 8 Appliances. 13 8.1 Installation of appliances . 13 8.2 Restriction concerning supply of appliances . 13 SIST EN 1646-1:2018
EN 1646-1:2018 (E) 3 9 Heating . 13 10 Installations . 14 10.1 Electricity . 14 10.1.1 Low voltage . 14 10.1.2 Extra low voltage . 14 10.2 Liquefied petroleum gas (LPG) . 14 11 Ventilation . 14 11.1 General . 14 11.2 Adjustment of ventilators . 14 11.3 Location of ventilation openings . 14 12 Fire precautions . 14 12.1 Means of escape . 14 12.1.1 Emergency exits . 14 12.1.2 Escape path . 14 12.1.3 Sanitation compartments . 15 12.1.4 Emergency doors . 15 12.1.5 Interior doors . 15 12.1.6 Emergency windows and emergency panels . 15 12.1.7 Work surfaces . 17 12.1.8 Heating and cooking equipment . 17 12.2 Protection of flammable elements . 17 12.2.1 Rigid or guided elements . 17 12.2.2 Non-guided elements . 18 12.3 Hotplates . 18 13 Warning notice . 18 13.1 Provision of warning notice . 18 13.2 Content of warning notice . 18 14 User's handbook . 19 Annex A (normative)
Strength of entrance step (see 5.3). 22 A.1 Principle . 22 A.2 Preparation and procedure . 22 A.3 Expression of results . 22 A.4 Test report . 23 Annex B (normative)
Slip resistance test (see 5.2.4) . 24 B.1 Principle . 24 B.2 Preparation and procedure . 24 B.3 Expression of results . 25 B.4 Test Report . 25 Annex C (normative)
Separate entrance step stability test (see 5.2.4.2) . 26 C.1 Principle . 26 C.2 Preparation and procedure . 26 C.3 Expression of results . 27 C.4 Test report . 27 Annex D (normative)
Clear height over bunks (see 6.1.2) . 28 D.1 Principle . 28 D.2 Preparation and procedure . 28 D.3 Expression of results . 28 D.4 Test report . 28 SIST EN 1646-1:2018
EN 1646-1:2018 (E) 4 Annex E (normative)
Strength of protection against falling out of bunks (see 6.1.3.3) . 29 E.1 Principle . 29 E.2 Preparation and procedure . 29 E.3 Expression of results . 29 E.4 Test report . 29 Annex F (normative)
Mechanical strength of bunks (see 6.1.4) . 30 F.1 Principle . 30 F.2 Selection of bunk . 30 F.3 Preparation and procedure . 30 F.4 Expression of results . 30 F.5 Test report . 30 Annex G (normative)
Security of folding bunks (see 6.1.5) . 32 G.1 Principle . 32 G.2 Preparation and procedure . 32 G.3 Expression of results . 32 G.4 Test report . 32 Annex H (normative)
Safety of access to high level bunks (see 6.1.6) . 33 H.1 Principle . 33 H.2 Preparation and procedure . 33 H.2.1 General . 33 H.2.2 Attachment and deflection . 33 H.3 Expression of results . 33 H.4 Test report . 33 Annex I (normative)
Measurement of gaps (see 6.1.7) . 35 I.1 Cone measuring device . 35 I.2 Gaps in the base structure . 35 I.3 Measurement of gaps . 36 Annex J (normative)
Heating (see Clause 9) . 37 J.1 Principle . 37 J.2 Preparation and procedure . 37 J.3 Expression of results . 37 J.4 Test report . 38 Annex K (normative)
Test equipment . 39 K.1 General . 39 K.2 Load measuring cell . 39 K.3 Load measuring cell . 39 K.4 Certified weights . 39 K.5 Load spreading platform . 39 K.6 Load spreading platform . 39 K.7 Step testing device . 39 K.8 Flexible load spreading device . 40 K.9 Step testing plate . 40 K.10 Friction test piece . 40 K.11 Ball . 41 K.12 Cone measuring device . 41 Annex L (informative)
Environmental aspects . 42 Bibliography . 43
SIST EN 1646-1:2018
EN 1646-1:2018 (E) 5 European foreword This document (EN 1646-1:2018) has been prepared by Technical Committee CEN/TC 245 “Leisure accommodation vehicles”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2018, and conflicting national standards shall be withdrawn at the latest by August 2018. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1646-1:2012. In relation to EN 1646-1:2012, the main technical changes are: a) reference to EN 1646-2 (withdrawn) deleted throughout the document; b) in 5.2.2 “Minimum tread dimensions”, requirements specified; c) new 5.3.4 added for dead-locking systems; d) 6.1.3 “Protection against falling out” simplified; e) in 7.4.2 “Outlets and couplings from toilet holding tanks”, requirements specified and extended; f) 12.1.2 “Escape path” and 12.1.3 “Sanitation compartment” clarified; g) 12.1.6 “Emergency windows and emergency panels” modified; h) 12.2 “Protection of flammable elements” specified; i) in Clause 14 “User's handbook”, information added and new types of fire extinguisher covered; j) normative references updated; k) editorially modified. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 1646-1:2018
EN 1646-1:2018 (E) 6 Introduction Figure 1 gives an overview of the relevant European Standards for caravans, motor caravans and caravan holiday homes.
Figure 1 — Overview of relevant European Standards applying to leisure accommodation vehicles SIST EN 1646-1:2018
EN 1646-1:2018 (E) 7 1 Scope This document specifies requirements intended to ensure the safety and health of persons when they use motor caravans for temporary or seasonal habitation. It also specifies the corresponding test methods. Specific requirements of this document apply to motor caravans where the overall length multiplied by the overall width does not exceed 13,5 m2 plan area. Requirements applicable to road safety are not included in the scope of this document. This document is applicable exclusively to motor caravans as defined in EN 13878. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3-7, Portable fire extinguishers — Part 7: Characteristics, performance requirements and test methods EN 721, Leisure accommodation vehicles — Safety ventilation requirements EN 1648-2, Leisure accommodation vehicles — 12 V direct current extra low voltage electrical installations — Part 2: Motor caravans EN 1949, Specification for the installation of LPG systems for habitation purposes in leisure accommodation vehicles and accommodation purposes in other vehicles EN 13878, Leisure accommodation vehicles — Terms and definitions HD 60364-7-721, Low-voltage electrical installations — Part 7-721: Requirements for special installations or locations — Electrical installations in caravans and motor caravans (IEC 60364-7-721) EN ISO 8936, Awnings for leisure accommodation vehicles — Requirements and test methods (ISO 8936) ISO 4649:2017, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13878 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses:
IEC Electropedia: available at http://www.electropedia.org/
ISO Online browsing platform: available at http://www.iso.org/obp 4 Testing The tests described in Annexes A to K are intended to verify that a motor caravan representative of a given model, including its fixtures and fittings, meets the requirements of this document. These tests are intended to simulate the most onerous conditions, for the relevant characteristics. SIST EN 1646-1:2018
EN 1646-1:2018 (E) 8 It is recommended to take environmental aspects into account during development, production and disposal of motor caravans based on established knowledge and within the respective technical possibilities (see also Annex L). 5 Design and construction 5.1 Occupancy The manufacturer shall designate the occupancy as the number of berths, both standard berths and additional berth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.