SIST EN 60317-56:2018

Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)

This part of IEC 60317 specifies the requirements of solderable fully insulated (FIW) zerodefect
enamelled round copper wire, class 180, with a single coating based on polyurethane
resin, which may be modified providing it retains its chemical identity and satisfies all the
required technical specifications.
The range of nominal conductor diameters of the wires covered by this standard is as follows:
• Grade of FIW 4, 6, 8: 0,090 mm up to and including 0,900 mm.
Nominal conductor diameters are specified in IEC 60317-0-7–.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 56: Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180

Spécifications pour types particuliers de fils de bobinage - Partie 56: Fil brasable de section circulaire, isolé en continu, en cuivre émaillé avec polyuréthane sans défaut électrique, classe 180

IEC 60317-56:2017 spécifie les exigences d'un fil de bobinage brasable, isolé en continu (FIW: fully insulated wire), sans défaut électrique, de section circulaire en cuivre émaillé, de classe 180, avec un revêtement unique à base de résine polyuréthane pouvant être modifiée à condition qu'elle conserve son identité chimique et satisfasse à toutes les spécifications techniques exigées. La gamme des diamètres nominaux des conducteurs des fils couverts par la présente norme est la suivante: Grade de FIW 4, 6, 8: 0,090 mm jusques et y compris 0,900 mm. Les diamètres nominaux des conducteurs sont spécifiés dans l’IEC 60317-0-7. Cette deuxième édition annule et remplace la première édition parue en 2012. Cette édition constitue une révision technique. La présente édition inclut les modifications techniques majeures suivantes par rapport à l’édition précédente:
- Article 1: révision du domaine d’application, réduisant le nombre de grades FIW compris entre 3 et 9, à seulement 4, 6 et 8;
- Article 1: révision du domaine d’application, réduisant la gamme de diamètres des conducteurs, qui passe de (0,040 à 1,600) mm à (0,090 à 0,900) mm;
- ajout d’une annexe informative relative aux exigences de résistance à l’abrasion pour les grades FIW 3 à 9.
Mots clés: fils isolés utilisés dans les enroulements des appareils électriques, section circulaire en cuivre émaillé, classe 180

Specifikacije za posebne vrste navijalnih žic - 56. del: Spajkljive, popolnoma izolirane in s poliuretanom brezhibno pološčene okrogle bakrene žice, razred 180 (IEC 60317-56:2017)

Ta del standarda IEC 60317 določa zahteve za spajkljivo, popolnoma izolirano (FIW) in brezhibno lakirano okroglo bakreno žico, razreda 180, z enim samim premazom na osnovi poliuretanske smole, ki se lahko spremeni, če ohrani svojo kemijsko identiteto in izpolnjuje vse zahtevane tehnične specifikacije.
Razponi nazivnih premerov prevodnikov žic, ki jih zajema ta standard, so:
• razred FIW 4, 6, 8: 0,090 mm do največ 0,900 mm.
Nazivni premeri prevodnika so določeni v standardu IEC 60317-0-7–.

General Information

• Status: Published
• Publication Date: 26-Nov-2017
• ICS: 29.060.10 - Wires
• ICS: 77.150.30 - Copper products
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 14-Nov-2017
• Due Date: 19-Jan-2018
• Completion Date: 27-Nov-2017
• Ref Project: EN 60317-56:2017 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180

Relations

• Revised: SIST EN 60317-56:2012 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180
• Effective Date: 08-Sep-2015
• Replaces: SIST EN 60317-56:2012 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180
• Effective Date: 13-Nov-2017

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)77.150.30Bakreni izdelkiCopper products29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-56:2017SIST EN 60317-56:2018en01-januar-2018SIST EN 60317-56:2018SLOVENSKI
STANDARDSIST EN 60317-56:20121DGRPHãþD



SIST EN 60317-56:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 60317-56
October 2017 ICS 29.060.10
Supersedes
EN 60317-56:2012
English Version
Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)
Spécifications pour types particuliers de fils de bobinage - Partie 56: Fil brasable de section circulaire, isolé en continu, en cuivre émaillé avec polyuréthane sans défaut électrique, classe 180 (IEC 60317-56:2017)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 56: Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180 (IEC 60317-56:2017) This European Standard was approved by CENELEC on 2017-09-13. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,
B-1000 Brussels © 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60317-56:2017 E SIST EN 60317-56:2018



EN 60317-56:2017 2 European foreword The text of document 55/1616/FDIS, future edition 2 of IEC 60317-56, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-56:2017. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2018-06-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2020-09-13
This document supersedes EN 60317-56:2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-56:2017 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 (series) NOTE Harmonized as EN 60264 (series). IEC 60317 (series) NOTE Harmonized as EN 60317 (series). IEC 60851 (series) NOTE Harmonized as EN 60851 (series).
SIST EN 60317-56:2018



EN 60317-56:2017 3
Annex ZA (normative)
Normative references to international publications with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu.
Publication Year Title EN/HD Year IEC 60317-0-7 -
FprEN 60317-0-7 -
SIST EN 60317-56:2018



SIST EN 60317-56:2018



IEC 60317-56 Edition 2.0 2017-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires –
Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180
Spécifications pour types particuliers de fils de bobinage –
Partie 56: Fil brasable de section circulaire, isolé en continu, en cuivre émaillé avec polyuréthane sans défaut électrique, classe 180
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE
ICS 29.060.10
ISBN 978-2-8322-4680-1
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60317-56:2018



– 2 – IEC 60317-56:2017 © IEC 2017 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions, general notes and appearance . 6 3.1 Terms and definitions . 6 3.2 General notes . 6 3.2.1 Methods of test . 6 3.2.2 Winding wire . 6 3.3 Appearance . 7 4 Dimensions. 7 5 Electrical resistance . 7 6 Elongation . 7 7 Springiness . 7 8 Flexibility and adherence . 7 9 Heat shock . 7 10 Cut-through . 7 11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including 0,900 mm) . 7 12 Resistance to solvents . 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17 Solderability . 8 18 Heat or solvent bonding . 9 19 Dielectric dissipation factor . 9 20 Resistance to transformer oil . 9 21 Loss of mass . 9 23 Pin-hole test . 9 30 Packaging . 9 Annex A (informative)
Resistance to abrasion . 10 A.1 Grades of FIW 3, 5, 7, 9 . 10 A.2 Grades 3 through 9 . 10 Bibliography . 11
Table 1 – Resistance to abrasion . 8 Table A.1 – Resistance to abrasion of FIW grades 3 through 9 . 10
SIST EN 60317-56:2018



IEC 60317-56:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES –
Part 56: Solderable fully insulated (FIW) zero-defect
polyurethane enamelled round copper wire, class 180
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization co
...