SIST EN ISO 16841:2014
(Main)Steel wire ropes - Pulling eyes for rope installation - Types and minimum requirements (ISO 16841:2014)
Steel wire ropes - Pulling eyes for rope installation - Types and minimum requirements (ISO 16841:2014)
EN ISO 16841 identifies the different types of pulling eyes that are prepared at, or attached to, a steel wire rope end for connection to another rope when installing a new rope or re-reeving an existing rope on a machine. This International Standard also specifies the minimum requirements for pulling eyes, including their geometry, strength, maximum line pull to which the pulling eye should be subjected and information for use to be provided by the manufacturer. The pulling eyes covered by this International Standard are not intended to be subject to a load when the machine performs a service operation. This International Standard applies to those pulling eyes that are prepared at, or attached to, ends of steel wire ropes conforming to ISO 2408 and ISO 10425. This International Standard does not apply to steel wire ropes with fibre cores. This International Standard does not cover those separate end connection accessories that slide over the end of a rope and comprise an eye and tubular type braided rope, often referred to as a ‘wire rope stocking’ or ‘cable sock’.
Stahldrahtseile - Einziehösen für die Seilmontage - Formen und Mindestanforderungen (ISO 16841:2014)
Diese Internationale Norm legt die verschiedenen Formen von Einziehösen fest, die am Seilende eines Stahl-drahtseils zum Verbinden mit einem anderen Seil angefertigt oder an dieses befestigt werden, wenn ein neues Seil montiert oder das bereits vorhandene Seil an einer Maschine umgeschert wird.
Diese Internationale Norm legt außerdem die Mindestanforderungen an Einziehösen fest, einschließlich deren Geometrie, Festigkeit, maximale Axialzugkraft, der die Einziehöse voraussichtlich ausgesetzt wird sowie vom Hersteller anzugebende Benutzerinformationen.
Die in dieser Internationalen Norm behandelten Einziehösen sind nicht dafür vorgesehen, einer Last ausgesetzt zu werden, während Wartungsarbeiten an der Maschine durchgeführt werden.
Diese Internationale Norm gilt für solche Einziehösen, die an den Seilenden von Stahldrahtseilen nach ISO 2408 und ISO 10425 angefertigt oder an diesen befestigt werden.
Diese Internationale Norm gilt nicht für Stahldrahtseile mit Fasereinlage.
Diese Internationale Norm behandelt keine separaten Zubehörteile für Seilendverbindungen, die über ein Seil-ende geschoben werden und aus einer Öse sowie einem röhrenartig geflochtenen Seil bestehen, häufig als Drahtseilstrumpf bzw. Kabelstrumpf bezeichnet.
Câbles en acier - Anneaux de tirage - Types et exigences minimales (ISO 16841:2014)
L'ISO 16841:2014 définit les différents types d'?ils de tirage qui sont préparés sur l'extrémité d'un câble en acier ou fixés à celle-ci pour le raccorder à un autre câble lors de l'installation d'un nouveau câble ou du mouflage d'un câble existant sur une machine. Elle spécifie également les exigences minimales pour les oeils de tirage, incluant leur géométrie, leur résistance, la force maximale exercée sur l'élingue pour laquelle les oeils de tirage sont destinés à être soumis ainsi que les informations pour l'utilisation à fournir par le fabricant.
Les oeils de traction couverts par l'ISO 16841:2014 ne sont pas destinés à être soumis à une charge lorsque la machine est en fonction.
L'ISO 16841:2014 s'applique aux oeils de tirage préparés ou fixés sur les extrémités de câbles d'acier conformes à l'ISO 2408 et à l'ISO 10425.
Jeklene žične vrvi - Pritrditvena ušesa za vgradnjo vrvi - Vrste in minimalne zahteve (ISO 16841:2014)
Standard EN ISO 16841 določa različne vrste pritrditvenih ušes, ki so pripravljena ali nameščena na konec jeklene žične vrvi, s čimer se med nameščanjem nove vrvi ali navijanjem obstoječe vrvi na napravo poveže drugo vrv. Ta mednarodni standard določa tudi minimalne zahteve za pritrditvena ušesa, vključno z njihovo geometrijo, močjo, največjim žičnim potegom, kateremu je pritrditveno uho lahko izpostavljeno, in informacijami o uporabi, ki jih poda proizvajalec. Pritrditvena ušesa, ki jih zajema ta mednarodni standard, niso namenjena izpostavljanju obremenitvam, ko naprava izvaja servisno operacijo. Ta mednarodni standard se uporablja za tista pritrditvena ušesa, ki so pripravljena ali nameščena na koncih jeklenih žičnih vrvi v skladu s standardoma ISO 2408 in ISO 10425. Ta mednarodni standard se ne uporablja za jeklene žične vrvi z vlaknastimi jedri. Ta mednarodni standard ne zajema pripomočkov z ločenim koncem, ki zdrsijo prek konca vrvi ter obsegajo uho in cevasto pleteno vrv, pogosto imenovano »kabelska vlečna nogavica«.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16841:2014
01-julij-2014
-HNOHQHåLþQHYUYL3ULWUGLWYHQDXãHVD]DYJUDGQMRYUYL9UVWHLQPLQLPDOQH
]DKWHYH ,62
Steel wire ropes - Pulling eyes for rope installation - Types and minimum requirements
(ISO 16841:2014)
Stahldrahtseile - Einziehösen für die Seilmontage - Formen und Mindestanforderungen
(ISO 16841:2014)
Câbles en acier - Anneaux de tirage - Types et exigences minimales (ISO 16841:2014)
Ta slovenski standard je istoveten z: EN ISO 16841:2014
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
SIST EN ISO 16841:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16841:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 16841:2014
EUROPEAN STANDARD
EN ISO 16841
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2014
ICS 77.140.65
English Version
Steel wire ropes - Pulling eyes for rope installation - Types and
minimum requirements (ISO 16841:2014)
Câbles en acier - Oeils de tirage pour les installations en Stahldrahtseile - Einziehösen für die Seilmontage - Formen
câble - Types et exigences minimales (ISO 16841:2014) und Mindestanforderungen (ISO 16841:2014)
This European Standard was approved by CEN on 15 February 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16841:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16841:2014
EN ISO 16841:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16841:2014
EN ISO 16841:2014 (E)
Foreword
This document (EN ISO 16841:2014) has been prepared by Technical Committee ISO/TC 105 “Steel wire
ropes” in collaboration with Technical Committee CEN/TC 168 “Chains, ropes, webbing, slings and
accessories - Safety” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2014, and conflicting national standards shall be
withdrawn at the latest by September 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16841:2014 has been approved by CEN as EN ISO 16841:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16841:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 16841:2014
INTERNATIONAL ISO
STANDARD 16841
First edition
2014-03-01
Steel wire ropes — Pulling eyes
for rope installation — Types and
minimum requirements
Câbles en acier — Oeils de tirage pour les installations en câble —
Types et exigences minimales
Reference number
ISO 16841:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 16841:2014
ISO 16841:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 16841:2014
ISO 16841:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 General . 2
4.2 Geometry . 3
4.3 Type testing . 6
4.4 Pulling eye working load limit (WLL) . 7
4.5 Welder qualification for rigid-type pulling eyes . 7
5 Verification of the requirements . 7
5.1 Tensile test . 7
5.2 Durability test . 8
6 Information for use . 8
6.1 Marking . 8
6.2 Certificate of compliance . 8
Annex A (informative) Determination of the line pull to which the pulling eye is subjected during
installation or a re-reeving operation . 9
Bibliography .10
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 16841:2014
ISO 16841:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 105, Steel wire ropes.
iv © ISO 2014 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 16841:2014
ISO 16841:2014(E)
Introduction
This International Standard was developed in response to a worldwide demand for an International
Standard identifying the different types of pulling eyes which are used to facilitate the installing and
re-reeving of ropes on a machine.
Such pulling eyes, sometimes referred to as beckets, are often used when another rope is required to
pull the new rope into place.
© ISO 2014 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 16841:2014
---------------------- Page: 12 ----------------------
SIST EN ISO 16841:2014
INTERNATIONAL STANDARD ISO 16841:2014(E)
Steel wire ropes — Pulling eyes for rope installation —
Types and minimum requirements
1 Scope
This International Standard identifies the different types of pulling eyes prepared at, or attached to, a
steel wire rope end for connection to another rope when installing a new rope or re-reeving an existing
rope on a machine.
This International Standard also specifies the minimum requirements for pulling eyes, including
their geometry, strength, maximum line pull to which the pulling eye is intended to be subjected and
information for use to be provided by the manufacturer.
The pulling eyes covered by this International Standard are not intended to be subjected to a load when
the machine performs a service operation.
This International Standard applies to those pulling eyes prepared at, or attached to, ends of steel wire
ropes conforming to ISO 2408 and ISO 10425.
This International Standard does not apply to steel wire ropes with fibre cores.
This International Standard does not cover those separate end connection accessories, which slide over
the end of a rope and comprise an eye- and tubular-type braided rope, often referred to as a “wire rope
stocking” or “cable sock”.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable to its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 7500-1, Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression
testing machines — Verification and calibration of the force-measuring system
ISO 17893, Steel wire ropes — Vocabulary, designation and classification
3 Terms and def
...
SLOVENSKI STANDARD
oSIST prEN ISO 16841:2012
01-oktober-2012
-HNOHQHåLþQHYUYL3ULWUGLWYHQDXãHVD]DYJUDGQMRYUYL9UVWHLQPLQLPDOQH
]DKWHYH ,62',6
Steel wire ropes - Pulling eyes for rope installation - Types and minimum requirements
(ISO/DIS 16841:2012)
Stahldrahtseile - Einziehösen für die Seilmontage - Formen und Mindestanforderungen
(ISO/DIS 16841:2012)
Câbles en acier - Anneaux de tirage - Types et exigences minimales (ISO/DIS
16841:2012)
Ta slovenski standard je istoveten z: prEN ISO 16841
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
oSIST prEN ISO 16841:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 16841:2012
---------------------- Page: 2 ----------------------
oSIST prEN ISO 16841:2012
EUROPEAN STANDARD
DRAFT
prEN ISO 16841
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2012
ICS 77.140.65
English Version
Steel wire ropes - Pulling eyes for rope installation - Types and
minimum requirements (ISO/DIS 16841:2012)
Câbles en acier - Anneaux de tirage - Types et exigences Stahldrahtseile - Einziehösen für die Seilmontage - Formen
minimales (ISO/DIS 16841:2012) und Mindestanforderungen (ISO/DIS 16841:2012)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 168.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 16841:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 16841:2012
prEN ISO 16841:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 16841:2012
prEN ISO 16841:2012 (E)
Foreword
This document (prEN ISO 16841:2012) has been prepared by Technical Committee ISO/TC 105 "Steel wire
ropes" in collaboration with Technical Committee CEN/TC 168 “Chains, ropes, webbing, slings and
accessories - Safety” the secretariat of which is held by BSI.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO/DIS 16841:2012 has been approved by CEN as a prEN ISO 16841:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 16841:2012
---------------------- Page: 6 ----------------------
oSIST prEN ISO 16841:2012
DRAFT INTERNATIONAL STANDARD ISO/DIS 16841
ISO/TC 105 Secretariat: SAC
Voting begins on Voting terminates on
2012-07-19 2012-12-19
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NORMALISATION
Steel wire ropes — Pulling eyes for rope installation — Types
and minimum requirements
Câbles en acier — Anneaux de tirage — Types et exigences minimales
[Revision of xxxxx edition (ISO #####-##:####)]
ICS 77.140.65
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME
STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2012
---------------------- Page: 7 ----------------------
oSIST prEN ISO 16841:2012
ISO/DIS 16841
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 16841:2012
ISO/DIS 16841
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Requirements.2
4.1 General .2
4.2 Geometry.3
4.2.1 Flexible type pulling eye made from the centre strand of the core .3
4.2.2 Flexible type pulling eye made from the steel core itself.3
4.2.3 Flexible type pulling eye made from the steel core and secured with pressed ferrules .3
4.2.4 Rigid type pulling eye .4
4.2.5 Semi-rigid type pulling eye.5
4.3 Type testing .5
4.3.1 Sampling .5
4.3.2 Minimum breaking force of pulling eye(F ) .5
p.e.min
4.3.3 Durability of pulling eyes intended to be used for multiple re-reeving operations.6
4.4 Pulling eye working load limit (WLL).6
4.5 Welder qualification for rigid type pulling eyes .6
5 Verification of the requirements .6
5.1 Tensile test.6
5.2 Durability test.7
6 Information for use.7
6.1 Marking.7
6.2 Certificate .7
Annex A (informative) Determination of the line pull to which the pulling eye will be subjected
during installation or a re-reeving operation.8
Bibliography.9
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 16841:2012
ISO/DIS 16841
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16841 was prepared by Technical Committee ISO/TC 105, Steel wire ropes, Subcommittee SC , .
This second/third/. edition cancels and replaces the first/second/. edition (), [clause(s) / subclause(s) /
table(s) / figure(s) / annex(es)] of which [has / have] been technically revised.
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
oSIST prEN ISO 16841:2012
ISO/DIS 16841
Introduction
This International Standard was developed in response to a worldwide demand for a standard identifying the
different types of Pulling Eyes that are used to facilitate the installing and re-reeving of ropes on a machine.
Such Pulling Eyes, sometimes referred to as beckets, are often used when another rope is required to pull the
new rope into place.
© ISO 2012 – All rights reserved v
---------------------- Page: 11 ----------------------
oSIST prEN ISO 16841:2012
---------------------- Page: 12 ----------------------
oSIST prEN ISO 16841:2012
DRAFT INTERNATIONAL STANDARD ISO/DIS 16841
Steel wire ropes — Pulling Eyes for Rope Installation — Types
and minimum requirements
1 Scope
This International Standard identifies the different types of pulling eyes that are prepared at, or attached to, a
steel wire rope end for connection to another rope when installing a new rope or re-reeving an existing rope
on a machine.
This International Standard also specifies the minimum requirements for pulling eyes, including their geometry,
strength, maximum line pull to which the pulling eye should be subjected and information for use to be
provided by the manufacturer.
The pulling eyes covered by this International Standard are not intended to be subject to a load when the
machine performs a service operation.
This International Standard applies to those pulling eyes that are prepared at, or attached to, ends of steel
wire ropes conforming to ISO 2408 and ISO 10425.
This International Standa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.