Steel wire ropes for general purposes - Minimum requirements

ISO 2408:2004 specifies minimum requirements for the manufacture and testing of stranded steel wire ropes for general purposes, including lifting equipment such as cranes and hoists. Ropes for slings are also dealt with, and tables giving minimum breaking forces for the more common sizes, grades and constructions of stranded rope presented. It is applicable to single-layer, rotation-resistant and parallel-closed ropes made from wires of uncoated (bright), zinc-coated and zinc-alloy coated finish in rope diameters of up to 60 mm, supplied as bulk manufacture. It is not applicable to ropes for mining purposes, aircraft control, the petroleum and natural gas industries, aerial ropeways and funiculars, lifts or for fishing purposes.

Câbles en acier pour usages courants - Exigences minimales

L'ISO 2408:2004 spécifie les exigences minimales pour la fabrication et les essais de câbles en acier à torons pour usages courants, y compris le matériel de levage tel que les grues et les treuils. Les câbles pour élingues sont également traités, et les charges de rupture minimales pour les dimensions, les qualités et les compositions les plus communes de câbles à torons sont données dans les tableaux. Elle s'applique aux câbles à une couche de torons, antigiratoires et disposés en parallèle, réalisés à partir de fils non revêtus (clairs), galvanisés ou revêtus d'un alliage de zinc, d'un diamètre inférieur ou égal à 60 mm, produits en masse. Elle ne s'applique pas aux câbles d'exploitation minière, aux câbles pour commandes d'aéronefs, aux câbles pour les industries du pétrole et du gaz naturel, aux câbles pour téléphériques et funiculaires, aux câbles d'ascenseurs ou aux câbles pour la pêche.

Jeklene vrvi za splošno uporabo - Minimalne zahteve

Ta mednarodni standard določa minimalne zahteve za izdelavo in preskušanje pramenastih jeklenih žičnih vrvi za splošno uporabo, vključno z dvigalno opremo, kot so žerjavi ter dvigala. Obravnavane so tudi vrvi za obese, pri čemer so v preglednicah navedene najmanjše pretržne trdnosti za pogostejše velikosti, razrede in konstrukcije pramenaste vrvi. Standard se uporablja za enoplastne, na vrtenje odporne in vzporedno zaprte vrvi, izdelane iz žic z neprevlečeno (svetlo), s cinkom prevlečeno in s cinkovo zlitino prevlečeno površino, pri čemer premer vrvi znaša do vključno 60 mm, dobavijo pa se kot masovni izdelani proizvodi.

General Information

Status
Published
Public Enquiry End Date
19-Feb-2012
Publication Date
26-Sep-2012
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
20-Aug-2012
Due Date
25-Oct-2012
Completion Date
27-Sep-2012

Relations

Buy Standard

Standard
ISO 2408:2004 - Steel wire ropes for general purposes -- Minimum requirements
English language
35 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 2408:2012
English language
40 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 2408:2004 - Câbles en acier pour usages courants -- Exigences minimales
French language
35 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


INTERNATIONAL ISO
STANDARD 2408
Third edition
2004-02-01
Steel wire ropes for general purposes —
Minimum requirements
Câbles en acier pour usages courants — Exigences minimales

Reference number
©
ISO 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved

Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Requirements . 2
4.1 Material. 2
4.2 Rope manufacture. 3
4.3 Designation and classification . 4
4.4 Dimensions. 4
4.5 Breaking force . 6
5 Verification of requirements and test methods . 7
5.1 Materials. 7
5.2 Rope manufacture. 7
5.3 Test on rope for diameter. 7
5.4 Test on rope for breaking force. 7
6 Information for use . 9
6.1 Certificate. 9
6.2 Packaging and marking. 10
Annex A (normative) Dimensional and mechanical properties of round wires (before ropemaking). 11
Annex B (normative) Sampling and acceptance criteria for type testing of ropes produced in
series. 14
Annex C (normative) Tables of minimum breaking forces for more common rope classes, sizes
and grades . 15
Annex D (normative) Calculation of minimum breaking force for ropes in the Tables of Annex C . 30
Annex E (informative) Tests on wires taken from the rope. 31
Annex F (informative) Comparison between metric and imperial rope sizes . 33
Annex G (informative) Rope grade equivalents. 34
Bibliography . 35

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2408 was prepared by Technical Committee ISO/TC 105, Steel wire ropes.
This third edition cancels and replaces the second edition (ISO 2408:1985), which has been technically
revised.
iv © ISO 2004 – All rights reserved

Introduction
This International Standard was developed in response to a worldwide demand for a specification giving
minimum requirements for ropes for general purposes.
As in previous editions, this edition of ISO 2408 specifies metric sizes and grades of rope for the more
common classes of rope. In addition, and for comparison, information is given in this edition on imperial rope
sizes and grades in order to assist in the rope selection process and help to ensure that existing levels of
safety are maintained on equipment originally designed to use such ropes. In these cases, it is recommended
that the equipment designer or rope manufacturer (or other competent person) be consulted prior to ordering
a substitute rope.
This International Standard does not restrict itself to those classes covered by the tables: other types, such as
ropes with compacted strands and compacted (swaged) ropes, may also conform to it.
Complementing this International Standard is ISO 17893, which covers definitions, designation and classification.

INTERNATIONAL STANDARD ISO 2408:2004(E)

Steel wire ropes for general purposes — Minimum requirements
1 Scope
This International Standard specifies minimum requirements for the manufacture and testing of stranded steel
wire ropes for general purposes, including lifting equipment such as cranes and hoists. Ropes for slings are
also dealt with, and tables giving minimum breaking forces for the more common sizes, grades and
constructions of stranded rope presented. It is applicable to single-layer, rotation-resistant and parallel-closed
ropes made from wires of uncoated (bright), zinc-coated and zinc-alloy coated finish in rope diameters of up to
60 mm, supplied as bulk manufacture. It is not applicable to ropes for
 mining purposes,
 aircraft control,
 the petroleum and natural gas industries,
 aerial ropeways and funiculars,
 lifts, or
 fishing purposes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2232:1990, Round drawn wire for general purpose non-alloy steel wire ropes and for large diameter steel
wire ropes — Specifications
ISO 3108, Steel wire ropes for general purposes — Determination of actual breaking load
ISO 4345, Steel wire ropes — Fibre main cores — Specification
ISO 4346, Steel wire ropes for general purposes — Lubricants — Basic requirements
ISO 6892, Metallic materials — Tensile testing at ambient temperature
ISO 7800, Metallic materials — Wire — Simple torsion test
ISO 10425:2003, Steel wire ropes for the petroleum and natural gas industries — Minimum requirements and
terms of acceptance
1)
ISO 17893 , Steel wire ropes — Vocabulary, designations and classifications

1) To be published.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 17893 apply.
4 Requirements
4.1 Material
4.1.1 Wire
Before ropemaking, wires shall conform to the diameter, torsion and, where applicable, coating requirements
specified in Annex A.
NOTE 1 Annex A is based on ISO 2232 but with extended wire sizes and wire tensile strength grades.
NOTE 2 For a given wire size and tensile strength grade, the torsional properties of the wires in A.2 of ISO 10425:2003
meet or exceed the values given in Annex A of this International Standard.
For those ropes where a rope grade is applicable, the tensile strength grades of the wires shall be subject to
the limits given in Table 1.
Table 1 — Tensile strength grades of wires (excluding centre and filler wires) for given rope grades
Rope grade Range of wire tensile strength grades
N/mm
1570 1 370 to 1 770
1770 1 570 to 1 960
1960 1 770 to 2 160
2160 1 960 to 2 160
NOTE 3 The minimum breaking force values of those ropes of grades 1570, 1770, 1960 and 2160 as covered by
Tables C.1 to C.14 are calculated on the basis of rope grade and not individual wire tensile strength grades.
All wires of the same nominal diameter in the same wire layer shall be of the same tensile strength grade.
The methods of test shall be in accordance with ISO 2232.
4.1.2 Core
Cores of single-layer stranded ropes shall normally be of steel or fibre, although other types such as
composites (e.g. steel plus fibre or steel plus polymer) or solid polymer may also be supplied.
The purchaser should specify any particular core type requirements.
Fibre cores for single-layer stranded ropes shall conform to ISO 4345 and for rope diameters 8 mm and above
shall be doubly closed (i.e. from yarn into strand and from strand into rope).
Natural fibre cores shall be treated with an impregnating compound to inhibit rotting and decay.
Steel cores shall be either an independent wire rope (IWRC) or a wire strand (WSC).
Steel cores of single-layer stranded ropes larger than 12 mm diameter shall be an independent wire rope
(IWRC), unless specified otherwise.
2 © ISO 2004 – All rights reserved

4.1.3 Lubricant
Lubricants shall conform to ISO 4346.
4.2 Rope manufacture
4.2.1 General
All the wires in a strand shall have the same direction of lay.
The core, except for compacted (swaged) ropes, shall be designed (steel) or selected (fibre) so that in a new
rope under tension on the closing machine there is clearance between the outer strands.
The completed rope shall be evenly laid and free from loose wires, distorted strands and other irregularities.
When uncoiled and under no load the rope shall not be wavy.
Rope ends that have no end fittings shall, when necessary, be so secured as to maintain the integrity of the
rope and prevent its unravelling.
4.2.2 Wire joints
Wires over 0,4 mm in diameter shall, where necessary, have their ends joined by brazing or welding.
Wires up to and including 0,4 mm diameter shall, where necessary, be joined by brazing, welding, twisting or
by ends being simply inserted in the strand’s formation.
If twisting as a joint is performed during rope manufacture, any protruding twisted wire ends shall be removed
from the finished rope.
4.2.3 Lubrication
The amount of lubrication and type of lubricant shall be appropriate to the rope duty.
The purchaser should specify the rope duty or any particular lubrication requirements.
4.2.4 Preformation and postformation
Ropes shall be preformed and/or postformed unless specified otherwise by the purchaser.
NOTE Some parallel-closed and rotation-resistant ropes could be non-preformed or be only partially preformed.
4.2.5 Construction
The rope construction shall be either one of those covered by the following classes or a construction, including
compacted strand ropes and compacted (swaged) ropes, as stated by the manufacturer:
6 × 7, 6
...


SLOVENSKI STANDARD
01-oktober-2012
1DGRPHãþD
SIST ISO 2408:1997
Jeklene vrvi za splošno uporabo - Minimalne zahteve
Steel wire ropes for general purposes - Minimum requirements
Câbles en acier pour usages courants - Exigences minimales
Ta slovenski standard je istoveten z: ISO 2408:2004
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 2408
Third edition
2004-02-01
Steel wire ropes for general purposes —
Minimum requirements
Câbles en acier pour usages courants — Exigences minimales

Reference number
©
ISO 2004
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved

Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Terms and definitions. 2
4 Requirements . 2
4.1 Material. 2
4.2 Rope manufacture. 3
4.3 Designation and classification . 4
4.4 Dimensions. 4
4.5 Breaking force . 6
5 Verification of requirements and test methods . 7
5.1 Materials. 7
5.2 Rope manufacture. 7
5.3 Test on rope for diameter. 7
5.4 Test on rope for breaking force. 7
6 Information for use . 9
6.1 Certificate. 9
6.2 Packaging and marking. 10
Annex A (normative) Dimensional and mechanical properties of round wires (before ropemaking). 11
Annex B (normative) Sampling and acceptance criteria for type testing of ropes produced in
series. 14
Annex C (normative) Tables of minimum breaking forces for more common rope classes, sizes
and grades . 15
Annex D (normative) Calculation of minimum breaking force for ropes in the Tables of Annex C . 30
Annex E (informative) Tests on wires taken from the rope. 31
Annex F (informative) Comparison between metric and imperial rope sizes . 33
Annex G (informative) Rope grade equivalents. 34
Bibliography . 35

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2408 was prepared by Technical Committee ISO/TC 105, Steel wire ropes.
This third edition cancels and replaces the second edition (ISO 2408:1985), which has been technically
revised.
iv © ISO 2004 – All rights reserved

Introduction
This International Standard was developed in response to a worldwide demand for a specification giving
minimum requirements for ropes for general purposes.
As in previous editions, this edition of ISO 2408 specifies metric sizes and grades of rope for the more
common classes of rope. In addition, and for comparison, information is given in this edition on imperial rope
sizes and grades in order to assist in the rope selection process and help to ensure that existing levels of
safety are maintained on equipment originally designed to use such ropes. In these cases, it is recommended
that the equipment designer or rope manufacturer (or other competent person) be consulted prior to ordering
a substitute rope.
This International Standard does not restrict itself to those classes covered by the tables: other types, such as
ropes with compacted strands and compacted (swaged) ropes, may also conform to it.
Complementing this International Standard is ISO 17893, which covers definitions, designation and classification.

INTERNATIONAL STANDARD ISO 2408:2004(E)

Steel wire ropes for general purposes — Minimum requirements
1 Scope
This International Standard specifies minimum requirements for the manufacture and testing of stranded steel
wire ropes for general purposes, including lifting equipment such as cranes and hoists. Ropes for slings are
also dealt with, and tables giving minimum breaking forces for the more common sizes, grades and
constructions of stranded rope presented. It is applicable to single-layer, rotation-resistant and parallel-closed
ropes made from wires of uncoated (bright), zinc-coated and zinc-alloy coated finish in rope diameters of up to
60 mm, supplied as bulk manufacture. It is not applicable to ropes for
 mining purposes,
 aircraft control,
 the petroleum and natural gas industries,
 aerial ropeways and funiculars,
 lifts, or
 fishing purposes.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 2232:1990, Round drawn wire for general purpose non-alloy steel wire ropes and for large diameter steel
wire ropes — Specifications
ISO 3108, Steel wire ropes for general purposes — Determination of actual breaking load
ISO 4345, Steel wire ropes — Fibre main cores — Specification
ISO 4346, Steel wire ropes for general purposes — Lubricants — Basic requirements
ISO 6892, Metallic materials — Tensile testing at ambient temperature
ISO 7800, Metallic materials — Wire — Simple torsion test
ISO 10425:2003, Steel wire ropes for the petroleum and natural gas industries — Minimum requirements and
terms of acceptance
1)
ISO 17893 , Steel wire ropes — Vocabulary, designations and classifications

1) To be published.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 17893 apply.
4 Requirements
4.1 Material
4.1.1 Wire
Before ropemaking, wires shall conform to the diameter, torsion and, where applicable, coating requirements
specified in Annex A.
NOTE 1 Annex A is based on ISO 2232 but with extended wire sizes and wire tensile strength grades.
NOTE 2 For a given wire size and tensile strength grade, the torsional properties of the wires in A.2 of ISO 10425:2003
meet or exceed the values given in Annex A of this International Standard.
For those ropes where a rope grade is applicable, the tensile strength grades of the wires shall be subject to
the limits given in Table 1.
Table 1 — Tensile strength grades of wires (excluding centre and filler wires) for given rope grades
Rope grade Range of wire tensile strength grades
N/mm
1570 1 370 to 1 770
1770 1 570 to 1 960
1960 1 770 to 2 160
2160 1 960 to 2 160
NOTE 3 The minimum breaking force values of those ropes of grades 1570, 1770, 1960 and 2160 as covered by
Tables C.1 to C.14 are calculated on the basis of rope grade and not individual wire tensile strength grades.
All wires of the same nominal diameter in the same wire layer shall be of the same tensile strength grade.
The methods of test shall be in accordance with ISO 2232.
4.1.2 Core
Cores of single-layer stranded ropes shall normally be of steel or fibre, although other types such as
composites (e.g. steel plus fibre or steel plus polymer) or solid polymer may also be supplied.
The purchaser should specify any particular core type requirements.
Fibre cores for single-layer stranded ropes shall conform to ISO 4345 and for rope diameters 8 mm and above
shall be doubly closed (i.e. from yarn into strand and from strand into rope).
Natural fibre cores shall be treated with an impregnating compound to inhibit rotting and decay.
Steel cores shall be either an independent wire rope (IWRC) or a wire strand (WSC).
Steel cores of single-layer stranded ropes larger than 12 mm diameter shall be an independent wire rope
(IWRC), unless specified otherwise.
2 © ISO 2004 – All rights reserved

4.1.3 Lubricant
Lubricants shall conform to ISO 4346.
4.2 Rope manufacture
4.2.1 General
All the wires in a strand shall have the same direction of lay.
The core, except for compacted (swaged) ropes, shall be designed (steel) or selected (fibre) so that in a new
rope under tension on the closing machine there is clearance between the outer strands.
The completed rope shall be evenly laid and free from loose wires, distorted strands and other irregularities.
When uncoiled and under no load the rope shall not be wavy.
Rope ends that have no end fittings shall, when necessary, be so secured as to maintain the integrity of the
rope and prevent its unravelling.
4.2.2 Wire joints
Wires over 0,4 mm in diameter shall, where necessary, have their ends joined by brazing or welding.
Wires up to and including 0,4 mm diameter shall
...


NORME ISO
INTERNATIONALE 2408
Troisième édition
2004-02-01
Câbles en acier pour usages courants —
Exigences minimales
Steel wire ropes for general purposes — Minimum requirements

Numéro de référence
©
ISO 2004
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.

©  ISO 2004
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2004 – Tous droits réservés

Sommaire Page
Avant-propos. iv
Introduction . v
1 Domaine d'application. 1
2 Références normatives. 1
3 Termes et définitions . 2
4 Exigences. 2
4.1 Matière. 2
4.2 Fabrication du câble . 3
4.3 Désignation et classification. 5
4.4 Dimensions. 5
4.5 Charge de rupture . 6
5 Vérification des exigences et méthodes d'essai . 7
5.1 Matériaux. 7
5.2 Fabrication des câbles . 7
5.3 Essai de diamètre sur câble. 8
5.4 Essai de charge de rupture sur câble . 8
6 Informations d'utilisation . 9
6.1 Certificat. 9
6.2 Emballage et marquage. 10
Annexe A (normative) Caractéristiques dimensionnelles et mécaniques des fils ronds (avant la
fabrication du câble) . 11
Annexe B (normative) Échantillonnage et niveaux d'acceptation pour les essais de type des
câbles produits en série. 14
Annexe C (normative) Tableaux des charges de rupture minimales pour les câbles de classes, de
diamètres et de qualités les plus courants .15
Annexe D (normative) Calcul de la charge de rupture minimale pour les câbles traités dans les
tableaux de l'Annexe C. 30
Annexe E (normative) Essais sur fils décâblés. 31
Annexe F (informative) Comparaison entre les dimensions métriques et impériales des câbles. 33
Annexe G (informative) Équivalence des qualités de câble. 34
Bibliographie . 35

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 2408 a été élaborée par le comité technique ISO/TC 105, Câbles en acier.
Cette troisième édition annule et remplace la deuxième édition (ISO 2408:1985), dont elle constitue une
révision technique.
iv © ISO 2004 – Tous droits réservés

Introduction
La présente Norme internationale a été élaborée en réponse à une demande à l'échelle mondiale d'une
spécification donnant les exigences minimales applicables aux câbles pour usages courants.
Comme dans les précédentes éditions de la présente Norme internationale, les dimensions métriques et les
qualités du câble sont spécifiées pour les constructions de câbles les plus courantes. De plus, et à titre de
comparaison, des informations sont données dans la présente édition sur les dimensions impériales et les
qualités afin d'en faciliter le choix et de contribuer à garantir que les niveaux de sécurité existants sont
conservés sur l'équipement initialement conçu pour utiliser de tels câbles. En pareil cas, il est recommandé de
consulter le concepteur de l'équipement ou le fabricant de câbles (ou toute autre personne compétente) avant
toute commande d'un autre câble.
La présente Norme internationale ne se limite pas aux classes de résistance traitées dans les tableaux;
d'autres types, tels que les câbles à torons compactés et les câbles compactés (martelés) peuvent également
s'avérer conformes à la présente Norme internationale.
Pour compléter la présente Norme internationale, l'ISO 17893, qui traite des définitions, de la désignation et
de la classification, a également été élaborée.

NORME INTERNATIONALE ISO 2408:2004(F)

Câbles en acier pour usages courants — Exigences minimales
1 Domaine d'application
La présente Norme internationale spécifie les exigences minimales pour la fabrication et les essais de câbles
en acier à torons pour usages courants, y compris le matériel de levage tel que les grues et les treuils. Les
câbles pour élingues sont également traités, et les charges de rupture minimales pour les dimensions, les
qualités et les compositions les plus communes de câbles à torons sont données dans les tableaux. Elle
s'applique aux câbles à une couche de torons, antigiratoires et disposés en parallèle, réalisés à partir de fils
non revêtus (clairs), galvanisés ou revêtus d'un alliage de zinc, d'un diamètre inférieur ou égal à 60 mm,
produits en masse.
Elle ne s'applique pas aux câbles
 d'exploitation minière,
 pour commandes d'aéronefs,
 pour les industries du pétrole et du gaz naturel,
 pour téléphériques et funiculaires,
 d'ascenseurs, ou
 pour la pêche.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 2232:1990, Fils tréfilés ronds pour câbles d'usages courants en acier non allié et pour câbles en acier de
gros diamètre — Spécifications
ISO 3108, Câbles en acier pour usages courants — Détermination de la charge de rupture effective
ISO 4345, Câbles en acier — Âmes centrales en textile — Spécifications
ISO 4346, Câbles en acier d'usage courant — Lubrifiants — Exigences de base
ISO 6892, Matériaux métalliques — Essai de traction à température ambiante
ISO 7800, Matériaux métalliques — Fils — Essai de torsion simple
ISO 10425:2003, Câbles en acier pour les industries du pétrole et du gaz naturel — Exigences minimales et
conditions de réception
1)
ISO 17893 , Câbles en acier — Vocabulaire, désignations et classifications

1) À publier.
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 17893 s'appliquent.
4 Exigences
4.1 Matière
4.1.1 Fil
Avant la fabrication du câble, les fils doivent satisfaire aux exigences spécifiées dans l'Annexe A en matière
de diamètre, de torsion et, le cas échéant, de revêtement.
NOTE 1 L'Annexe A est fondée sur l'ISO 2232, la plage de diamètres et de classes de résistance à la traction étant
toutefois élargie.
NOTE 2 Pour un diamètre de fil et une classe de résistance à la traction donnés, les propriétés en torsion des fils
figurant en A.2 de l'ISO 10425:2003 sont conformes ou supérieures aux valeurs données dans l'Annexe A de la présente
Norme internationale.
Pour les câbles auxquels s'applique une qualité, les classes de résistance à la traction des fils doivent être
dans les limites indiquées dans le Tableau 1.
Tableau 1 — Classes de résistance à la traction des fils
(à l'exclusion des fils centraux et des fils de remplissage)
pour des qualités de câble données
Qualité de câble Plage de classes de résistance à la traction du fil
N/mm
1570 1 370 à 1 770
1770 1 570 à 1 960
1960 1 770 à 2 160
2160 1 960 à 2 160
NOTE 3 Les valeurs de la charge de rupture minimale des câbles des qualités 1570, 1770, 1960 et 2160 figurant dans
les Tableaux C.1 à C.14 sont calculées sur la base de la qualité de câble et non sur la base des diverses classes de
résistance des fils.
Tous les fils de même diamètre nominal d'une même couche doivent avoir la même classe de résistance.
Les méthodes d'essai doivent être conformes à celles données dans l'ISO 2232.
4.1.2 Âme
Les âmes des câbles à une couche de torons doivent normalement être en acier ou en textile, bien qu'il soit
permis de fournir également d'autres types, tels que des composites (par exemple acier plus textile ou acier
plus polymère) ou polymère solide.
Il convient que l'acheteur spécifie toute exigence particulière en matière de type d'âme.
Les âmes textiles des câbles à une couche de torons doivent être conformes à l'ISO 4345 et, dans le cas de
câbles ayant un diamètre égal ou supérieur à 8 mm, elles doivent être câblées en deux opérations (c'est-
à-dire de fil en toron et de toron en câble).
2 © ISO 2004 – Tous droits réservés

Les âmes textiles naturelles doivent être traitées avec un composé imprégnant pour empêcher leur
décomposition.
Les âmes en acier doivent être soit des âmes métalliques indépendantes câblées (IWRC), soit un toron
(WSC).
Sauf spécification contraire, les âmes en acier des câbles à une couche de torons, dont le diamètre est
supérieur à 12 mm, doivent être constituées d'un câble à fils indépendants (IWRC).
4.1.3 Lubrifiants
Les lubrifiants doivent être conformes à l'ISO 4346.
4.2 Fabrication du câble
4.2.1 Généralités
Tous les
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.