SIST EN 62841-1:2015
(Main)Electric Motor-Operated Hand-Held, Transportable Tools and Lawn and Garden Machinery - Safety - Part 1: General requirements
Electric Motor-Operated Hand-Held, Transportable Tools and Lawn and Garden Machinery - Safety - Part 1: General requirements
This standard deals with the safety of electric motor-operated or magnetically driven: - hand-held tools (IEC 62841-2); - transportable tools (IEC 62841-3); - lawn and garden machinery (IEC 62841-4). The above listed categories are hereinafter referred to as “tools” or “machines”. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. The rated input is not more than 3 700 W. The limits for the applicability of this standard for battery tools are given in K.1 and L.1. This standard deals with the hazards presented by tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Tools with electric heating elements are within the scope of this standard. Requirements for motors not isolated from the supply, and having basic insulation not designed for the rated voltage of the tools, are given in Annex B. Requirements for rechargeable battery-powered motor-operated or magnetically driven tools and the battery packs for such tools are given in Annex K. Requirements for such tools that are also operated and/or charged directly from the mains or a non-isolated source are given in Annex L. Hand-held electric tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard and such combination of a hand-held tool and a support is considered to be a transportable tool and thus covered by the relevant Part 3.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 1: Allgemeine Anforderungen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 1: Règles générales
L'IEC 62481-1:2014 traite de la sécurité des: - outils portatifs (CEI 62841-2) électroportatifs à moteur ou à entraînement magnétique; - outils portables (CEI 62841-3) électroportatifs à moteur ou à entraînement magnétique; - machines pour jardins et pelouses (CEI 62841-4) électroportatifs à moteur ou à entraînement magnétique. Les catégories énumérées ci-dessus sont appelées ci-après 'outils' ou 'machines'. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. La tension assignée est inférieure à 3 700 W. Les limites d'application de la présente Norme aux outils fonctionnant sur batterie sont indiquées en K.1 et L.1. La présente Norme traite des dangers présentés par les outils, encourus par tous les individus dans l'utilisation normale et dans l'utilisation impropre raisonnablement prévisible de ces outils. Les outils comportant des éléments chauffants électriques entrent dans le domaine d'application de la présente Norme. Les outils électroportatifs, qui peuvent être montés sur un support de travail pour être utilisés comme outils installés à poste fixe sans aucune modification de l'outil lui-même, sont compris dans le domaine d'application de la présente Norme et la combinaison d'un outil portatif et d'un support est considérée comme un outil portable, donc couvert par la Partie 3 applicable. La présente norme est prévue pour annuler et remplacer la quatrième édition de l'IEC 60745-1, publiée en 2006, la première édition de l'IEC 61029-1, publiée en 1990, et la cinquième édition de l'IEC 60335-1, publiée en 2010, uniquement en ce qui concerne les exigences ayant trait aux machines pour jardins et pelouses. Les dernières publications restent valides jusqu'à ce qu'elles soient retirées. La présente norme constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à la quatrième édition de la CEI 60745-1: - ajout ou modification d'exigences dans plusieurs articles, afin d'inclure les exigences relatives aux outils portables et aux machines pour jardins et pelouses (auparavant couverts par la CEI 61029-1 et la CEI 60335-1); - les essais de courant de fuite et de rigidité diélectrique ont été déplacés des Articles 13 et 15 aux Annexes C et D; - les Articles 29, 30 et 31 ont été renumérotés Articles 6, 13 et 15; - ajout à l'Article 18 des exigences relatives aux fonctions électroniques critiques pour la sécurité; - les exigences relatives aux interrupteurs ont été révisées et déplacées de l'Annexe I à l'Article 23; - les Articles 9, 19 et 13 ont été clarifiés en ce qui concerne les matériaux doux (élastomères); - le doigt d'épreuve de la Figure 1 de la CEI 60745-1 et la sonde d'essai de la Figure 2 de la CEI 60745-1 ont été remplacés par des références aux normes de base de la CEI; - ajout des exigences relatives aux systèmes de batterie Li-Ion aux Annexes K et L et la suppression de l'Annexe M. Mots-Clés: outils, électroportatif à moteur, portatif, portable, jardin et pelouse
Električna motorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 1. del: Splošne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 62841-1:2015
01-december-2015
1DGRPHãþD
SIST EN 60335-1:2012
SIST EN 60745-1:2009
SIST EN 60745-1:2009/A11:2010
SIST EN 61029-1:2009
SIST EN 61029-1:2009/A11:2011
(OHNWULþQDPRWRUQDURþQDRURGMDSUHQRVQDRURGMDWHUVWURML]DWUDWRLQYUW9DUQRVW
GHO 6SORãQH]DKWHYH
Electric Motor-Operated Hand-Held, Transportable Tools and Lawn and Garden
Machinery - Safety - Part 1: General requirements
Ta slovenski standard je istoveten z: EN 62841-1:2015
ICS:
25.140.20 (OHNWULþQDRURGMD Electric tools
65.060.70 Vrtnarska oprema Horticultural equipment
SIST EN 62841-1:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 62841-1:2015
---------------------- Page: 2 ----------------------
SIST EN 62841-1:2015
EUROPEAN STANDARD EN 62841-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2015
ICS 25.140.20 Supersedes EN 60335-1:2012 (partially), EN 60745-
1:2009, EN 61029-1:2009
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 1: General
requirements
(IEC 62841-1:2014 + corrigendum May 2014, modified)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 1: Règles transportable Werkzeuge und Rasen- und
générales Gartenmaschinen - Sicherheit - Teil 1: Allgemeine
(IEC 62841-1:2014 + corrigendum May 2014, modifiée) Anforderungen
(IEC 62841-1:2014 + corrigendum May 2014, modifiziert)
This European Standard was approved by CENELEC on 2015-06-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 62841-1:2015 E
---------------------- Page: 3 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Foreword
The text of document 116/156/FDIS, future edition 1 of IEC 62841-1, prepared by IEC/TC 116 "Safety of
motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and approved by
CENELEC as EN 62841-1:2015.
A draft amendment, which covers common modifications to IEC 62841-1, was prepared by CLC/TC 116
"Safety of motor-operated electric tools" and approved by CENELEC.
The following dates are fixed:
– latest date by which this document has to be implemented (dop) 2016-06-15
at national level by publication of an identical
national standard or by endorsement
– latest date by which the national standards conflicting (dow) -
with this document have to be withdrawn
The EN 62841 series supersedes the EN 60745 series, the EN 61029 series and (for lawn and garden
machinery) parts of the EN 60335 series.
This European Standard replaces EN 60745-1:2009 and EN 61029-1:2009. However, EN 60745-1:2009
and EN 61029-1:2009 remain valid until all Part 2’s which are used in conjunction with them have been
withdrawn. No date of withdrawal (dow) has been given pending the updating of all the Part 2’s to align
with this EN 62841-1:2015 as respective Part 2’s and Part 3’s. The applicable date of withdrawal is given
in each Part 2 and Part 3. It is intended the dow for this Part 1 will be fixed once all the Part 2’s and
Part 3’s have been published.
EN 62841-1:2015 includes the following significant technical changes:
− requirements in various clauses introduced or modified in order to include the requirements for
transportable tools and lawn and garden machinery (formerly covered by EN 61029-1 and
EN 60335-1);
− leakage current test and electric strength test moved from former Clauses 13 and 15 to Annexes C
and D;
− former Clauses 29, 30 and 31 renumbered to become Clauses 6, 13 and 15;
− requirements for electronic safety critical functions added to Clause 18;
− requirements for switches revised and moved from Annex I to Clause 23;
− clarifications in respect to soft materials (elastomers) added to Clauses 9, 19 and 13;
− test finger in Figure 1 of EN 60745-1 and test probe in Figure 2 of EN 60745-1 replaced by references
to basic IEC standards;
− requirements for Li-ion battery systems added to Annexes K and L;
− Annex M removed.
2
---------------------- Page: 4 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s), see informative Annex ZZ, which is an integral part of this
document.
This European Standard is divided into four parts:
Part 1: General requirements which are common to most electric motor operated tools (for the
purpose of this standard referred to simply as tools) which could come within the scope of
this standard;
Part 2, 3 or 4: Requirements for particular types of tools which either supplement or modify the
requirements given in Part 1 to account for the particular hazards and characteristics of
these specific tools.
This Part 1 is to be used in conjunction with the appropriate parts of EN 62841-2, EN 62841-3 or
EN 62841-4 which contain clauses that supplements or modify the corresponding clauses in Part 1 to
provide the relevant requirements for each type of product.
Compliance with the relevant clauses of Part 1 together with a relevant Part 2, 3 or 4 of this standard
provides one means of conforming with the essential health and safety requirements of the Directive
concerned.
A relevant Part 2, 3 or 4 is one in which the type of the tool or an accessory which is to be used with the
tool is within the scope of that Part 2, 3 or 4.
When a relevant Part 2, 3, or 4 does not exist, Part 1 can help to establish the requirements for the tool,
but will not by itself provide a means of conforming to the relevant essential health and safety
requirements of the Machinery Directive.
Warning: Other requirements and other EU Directives can be applicable to the products falling within
the scope of this standard.
CEN Technical Committees have produced a range of standards dealing with a similar range of non-
electrically powered tools. Where necessary, normative references are made to these standards in the
relevant Part 2, 3 or 4.
This European Standard follows the overall requirements of EN ISO 12100.
NOTE 1 In this standard, the following print types are used:
- requirements proper; in roman type
- test specifications: in italic type;
- explanatory matter: in smaller roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun
are also in bold.
NOTE 2 In Annexes B, K and L, subclauses which are additional to those in the main body of the text are numbered starting from
201.
NOTE 3 Clauses, subclauses, notes, tables, figures and annexes which are additional to those in IEC 62841-1:2014 are
prefixed “Z”.
3
---------------------- Page: 5 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Endorsement notice
The text of the International Standard IEC 62841-1:2014 + corrigendum May 2014 was approved by
CENELEC as a European Standard with agreed common modifications.
4
---------------------- Page: 6 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
COMMON MODIFICATIONS
2 Normative references
Add the following normative references:
CR 1030-1, Hand-arm vibration – Guidelines for vibration hazards reduction – Part 1: Engineering
methods by design of machinery
EN ISO 11688-1, Acoustics – Recommended practice for the design of low-noise machinery and
equipment – Part 1: Planning (ISO/TR 11688-1)
4 General requirements
Delete the third paragraph.
8 Marking and instructions
8.4
nd
Replace the 2 paragraph with the following:
Markings specified in 8.2 and 8.3 shall be clearly discernible from the outside of the tool. Other markings
on the tool may be visible after removal of a cover, provided that the location of the markings is readily
accessible.
8.14
nd
Add the following after the 2 paragraph:
The words "Original instructions" shall appear on the language version(s) verified by the manufacturer or
his authorised representative. Where no "Original instructions" exist in the official language(s) of the
country where the tool is to be used, a translation into that/those language(s) shall be provided by the
manufacturer or his authorised representative or by the person bringing the tool into the language area in
question. The translations shall bear the words "Translation of the original instructions", and they shall be
accompanied by a copy of the "Original instructions".
8.14.2
Add the following after d) 5):
Za) Emissions
1) The noise emission, measured in accordance with I.2, as follows:
− A-weighted emission sound pressure level L and its uncertainty K , where L exceeds
pA pA pA
70 dB(A).
Where L does not exceed 70 dB(A), this fact shall be indicated;
pA
− A-weighted sound power level L and its uncertainty K , where the A-weighted emission
WA WA
sound pressure level L exceeds 80 dB(A);
pA
− C-weighted peak emission sound pressure level L , where this exceeds 63 Pa (130 dB
pCpeak
in relation to 20 µPa).
5
---------------------- Page: 7 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
2) Recommendation for the operator to wear hearing protection.
3) The vibration total value and its uncertainty measured in accordance with I.3.
When the vibration total value does not exceed 2,5 m/s², this shall be stated.
When the vibration total value exceeds 2,5 m/s², its value shall be given in the instructions.
4) The following information:
− that the declared vibration total value(s) and the declared noise emission value(s) have
been measured in accordance with a standard test method and may be used for comparing
one tool with another;
− that the declared vibration total value(s) and the declared noise emission value(s) may also
be used in a preliminary assessment of exposure.
5) A warning:
− that the vibration and noise emissions during actual use of the power tool can differ from
the declared values depending on the ways in which the tool is used especially what kind
of workpiece is processed; and
− of the need to identify safety measures to protect the operator that are based on an
estimation of exposure in the actual conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched off and when it is running idle
in addition to the trigger time).
18 Abnormal operation
18.8.1
In Table 4, replace the table footnote by the following:
* Performance levels are to be specified in the relevant part of EN 62841-2, EN 62841-3 or EN 62841-4.
th
Delete the 5 paragraph and the subsequent NOTE 3.
21 Construction
nd
In 21.18.1, delete the 2 paragraph.
Add the following new subclause after 21.18.1.2:
21.18.1.Z1 Unless hand-held tools are equipped with a momentary power switch without lock-on
device, voltage recovery following an interruption of the supply shall not give rise to a hazard. The
relevant part of EN 62841-2 specifies if this subclause applies and gives specific requirements.
Compliance is checked by inspection.
Replace the existing Subclause 21.18.2.1 by the following:
21.18.2.1 Unless transportable tools are equipped with a momentary power switch without lock-on
device, voltage recovery following an interruption of the supply shall not give rise to a hazard. The
relevant part of EN 62841-3 specifies if this subclause applies and gives specific requirements.
Compliance is checked by inspection.
6
---------------------- Page: 8 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Annexes
Replace the existing Annex E by the following:
Annex E
Void
Replace the title of Annex I by the following:
Annex I
(normative)
Measurement of noise and vibration emissions
Add the following before I.2.1:
I.2.Z1 Noise reduction
Noise reduction at tools is an integral part of the design process and shall be achieved by particularly
applying measures at source to control noise, see for example EN ISO 11688-1. The success of the
applied noise reduction measures is assessed on the basis of the actual noise emission values in relation
to other machines of the same type with comparable non acoustical technical data.
The major sound sources of tools are: motor, fan, gear.
Add the following before I.3.1:
I.3.Z1 Vibration reduction
The vibration at the handles shall be kept as low as possible without unduly affecting the performance
and the ergonomics (weight, handling, etc.) of the tool.
In particular vibration shall be reduced by the application of engineering measures as given in CR 1030-1.
The success of the applied vibration measures is assessed by comparing the vibration levels for the tool
with those for other tools of the same type and with a comparable specification and performance.
th
Replace the 4 paragraph of I.3.5.1 with the following:
When the test procedure is not provided in a relevant part of EN 62841-2, EN 62841-3 or EN 62841-4, an
operating condition shall be specified that is reproducible and representative of the noisiest operation in
typical usage of the tool. The vibration test may simulate a single phase of a task or a working cycle,
consisting of a set of operations where the operator is being exposed to vibration. However, the operating
condition for the noise emission test shall, if practicable, also be used for the vibration test.
Annex K
(normative)
Battery tools and battery packs
In K.8.14.2, item e), add the following after 3):
Z1) For battery tools with integral battery: instruction, how the integral battery can be removed safely
from the tool after the tool’s end of life, and information about the type of battery such as Li-Ion,
NiCd and NiMH.
7
---------------------- Page: 9 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Annex L
(normative)
Battery tools and battery packs provided with mains connection
or non-isolated sources
In L.8.14.2, item e), add the following after 3):
Z1) For battery tools with integral battery: instruction, how the integral battery can be removed
safely from the tool after the tool’s end of life, and information about the type of battery such as
Li-Ion, NiCd and NiMH.
8
---------------------- Page: 10 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Add the following annexes:
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu
Publication Year Title EN/HD Year
IEC 60061 Series Lamp caps and holders together with EN 60061 Series
gauges for the control of interchangeability
and safety
1)
IEC 60065 (mod) 2001 Audio, video and similar electronic EN 60065 2002
1)
+ corr. August 2002 apparatus - Safety requirements + corr. August 2007
1)
+ A1 (mod) 2005 + A1 2006
1)
+ A2 (mod) 2010 + A2 2010
1)
- - + A11 2008
1)
- - + A12 2011
2)
IEC 60068-2-75 1997 Environmental testing EN 60068-2-75 1997
Part 2-75: Tests - Test Eh: Hammer tests
IEC/TR 60083 - Plugs and socket-outlets for domestic and - -
similar general use standardized in
member countries of IEC
IEC 60085 2007 Electrical insulation - Thermal evaluation EN 60085 2008
and designation
IEC 60127 Series Miniature fuses EN 60127 Series
IEC 60227 Series Polyvinyl chloride insulated cables of rated - -
voltages up to and including 450/750 V
IEC 60238 - Edison screw lampholders EN 60238 -
IEC 60245 Series Rubber insulated cables - Rated voltages - -
up to and including 450/750 V
IEC 60252-1 - AC motor capacitors EN 60252-1 -
Part 1: General - Performance, testing and
rating - Safety requirements - Guidance for
installation and operation
IEC 60320 Series Appliance couplers for household and EN 60320 Series
similar general purposes
———————
1)
Superseded by EN 60065:2014 (IEC 60065:2014): DOW = 2017-11-17.
2)
Superseded by EN 60068-2-75:2014 (IEC 60068-2-75:2014): DOW = 2017-10-08.
9
---------------------- Page: 11 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
IEC 60320-1 - Appliance couplers for household and EN 60320-1 -
similar general purposes
Part 1: General requirements
IEC 60335-1 (mod) 2010 Household and similar electrical EN 60335-1 2012
+ corr. July 2010 appliances - Safety
+ corr. April 2011 Part 1: General requirements
IEC 60384-14 - Fixed capacitors for use in electronic EN 60384-14 -
equipment
Part 14: Sectional specification - Fixed
capacitors for electromagnetic interference
suppression and connection to the supply
mains
IEC 60417 DB - Graphical symbols for use on equipment - -
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993
+ A1 1999 + A1 2000
+ A2 2013 + A2 2013
IEC 60664-1 - Insulation coordination for equipment EN 60664-1 -
within low-voltage systems
Part 1: Principles, requirements and tests
3)
IEC 60695-2-11 2000 Fire hazard testing EN 60695-2-11 2001
+ corr. January 2001 Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test
method for end-products
IEC 60695-2-13 2010 Fire hazard testing EN 60695-2-13 2010
+ corr. February 2012 Part 2-13: Glowing/hot-wire based test
methods - Glow-wire ignition temperature
(GWIT) test method for materials
4)
IEC 60695-10-2 2003 Fire hazard testing EN 60695-10-2 2003
+ corr. February 2006 Part 10-2: Abnormal heat - Ball pressure
test
IEC 60695-11-10 2013 Fire hazard testing EN 60695-11-10 2013
Part 11-10: Test flames - 50 W horizontal
and vertical flame test methods
IEC 60730-1 (mod) 2010 Automatic electrical controls for household EN 60730-1 2011
and similar use
Part 1: General requirements
5)
IEC 60825-1 2007 Safety of laser products EN 60825-1 2007
Part 1: Equipment classification and
requirements
IEC 60884 Series Plugs and socket-outlets for household - -
and similar purposes
IEC 60906-1 - IEC system of plugs and socket-outlets for - -
household and similar purposes
Part 1: Plugs and socket-outlets 16 A
250 V a.c.
———————
3)
Superseded by EN 60695-2-11:2014 (IEC 60695-2-11:2014): DOW = 2017-03-13.
4)
Superseded by EN 60695-10-2:2014 (IEC 60695-10-2:2014): DOW = 2017-03-26.
5)
Superseded by EN 60825-1:2014 (IEC 60825-1:2014): DOW = 2017-06-19.
10
---------------------- Page: 12 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
IEC 60990 1999 Methods of measurement of touch current EN 60990 1999
and protective conductor current
IEC 60998-2-1 - Connecting devices for low-voltage circuits EN 60998-2-1 -
for household and similar purposes
Part 2-1: Particular requirements for
connecting devices as separate entities
with screw-type clamping units
IEC 60998-2-2 - Connecting devices for low-voltage circuits EN 60998-2-2 -
for household and similar purposes
Part 2-2: Particular requirements for
connecting devices as separate entities
with screwless-type clamping units
IEC 60999-1 1999 Connecting devices - Electrical copper EN 60999-1 2000
conductors - Safety requirements for
screw-type and screwless-type clamping
units
Part 1: General requirements and
particular requirements for clamping units
for conductors from 0,2 mm² up to 35 mm²
(included)
IEC 61000-4-2 2008 Electromagnetic compatibility (EMC) EN 61000-4-2 2009
Part 4-2: Testing and measurement
techniques - Electrostatic discharge
immunity test
IEC 61000-4-3 2006 Electromagnetic compatibility (EMC) EN 61000-4-3 2006
+ A1 2007 Part 4-3: Testing and measurement + A1 2008
+ A2 2010 techniques - Radiated, radio-frequency, + A2 2010
electromagnetic field immunity test
IEC 61000-4-4 2012 Electromagnetic compatibility (EMC) EN 61000-4-4 2012
Part 4-4: Testing and measurement
techniques - Electrical fast transient/burst
immunity test
6)
IEC 61000-4-5 2005 Electromagnetic compatibility (EMC) EN 61000-4-5 2006
+ corr. October 2009 Part 4-5: Testing and measurement
techniques - Surge immunity test
7)
IEC 61000-4-6 2008 Electromagnetic compatibility (EMC) EN 61000-4-6 2009
Part 4-6: Testing and measurement
techniques - Immunity to conducted
disturbances, induced by radio-frequency
fields
IEC 61000-4-11 2004 Electromagnetic compatibility (EMC) EN 61000-4-11 2004
Part 4-11: Testing and measurement
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests
IEC 61032 1997 Protection of persons and equipment by EN 61032 1998
+ corr. January 2003 enclosures - Probes for verification
———————
6)
Superseded by EN 61000-4-5:2014 (IEC 61000-4-5:2014): DOW: 2017-06-19.
7)
Superseded by EN 61000-4-6:2014 (IEC 61000-4-6:2014): DOW: 2016-11-27.
11
---------------------- Page: 13 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
IEC 61056-1 - General purpose lead-acid batteries EN 61056-1 -
(valve-regulated types)
Part 1: General requirements, functional
characteristics - Methods of test
8)
IEC 61058-1 (mod) 2000 Switches for appliances EN 61058-1 2002
+ corr. January 2009 Part 1: General requirements - -
+ A1 2001
+ A2 2007 + A2 2008
IEC 61210 - Connecting devices - Flat quick-connect EN 61210 -
terminations for electrical copper
conductors - Safety requirements
9)
IEC 61540 1997 HD 639 S1 2002
+ A1 1998 + corr. July 2003
- - + A2 2010
IEC 61558-1 - Safety of power transformers, power EN 61558-1 -
supplies, reactors and similar products
Part 1: General requirements and tests
IEC 61558-2-4 - Safety of transformers, reactors, power EN 61558-2-4 -
supply units and similar products for
supply voltages up to 1 100 V
Part 2-4: Particular requirements and tests
for isolating transformers and power
supply units incorporating isolating
transformers
IEC 61558-2-6 - Safety of transformers, reactors, power EN 61558-2-6 -
supply units and similar products for
supply voltages up to 1 100 V
Part 2-6: Particular requirements and tests
for safety isolating transformers and power
supply units incorporating safety isolating
transformers
IEC 61558-2-16 - Safety of transformers, reactors, power EN 61558-2-16 -
supply units and similar products for
voltages up to 1 100 V
Part 2-16: Particular requirements and
tests for switch mode power supply units
and transformers for switch mode power
supply units
IEC 61951-1 - Secondary cells and batteries containing EN 61951-1 -
alkaline or other non-acid electrolytes -
Portable sealed rechargeable single cells
Part 1: Nickel-cadmium
IEC 61951-2 - Secondary cells and batteries containing EN 61951-2 -
alkaline or other non-acid electrolytes -
Portable sealed rechargeable single cells
Part 2: Nickel-metal hydride
IEC 61960 - Secondary cells and batteries containing EN 61960 -
alkaline or other non-acid electrolytes -
Secondary lithium cells and batteries for
portable applications
———————
8)
EN 61058-1 includes A1 to IEC 61058-1 (mod) + corr. January.
9)
HD 639 S1 includes A1 to IEC 61540.
12
---------------------- Page: 14 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
IEC 61984 - Connectors - Safety requirements and EN 61984 -
tests
IEC 62133 - Secondary cells and batteries containing EN 62133 -
alkaline or other non-acid electrolytes -
Safety requirements for portable sealed
secondary cells, and for batteries made
from them, for use in portable applications
IEC 62233 - Measurement methods for EN 62233 -
electromagnetic fields of household
appliances and similar apparatus with
regard to human exposure
IEC 62471 - Photobiological safety of lamps and lamp EN 62471 -
systems
IEC/TR 62471-2 2009 Photobiological safety of lamps and lamp - -
systems
Part 2: Guidance on manufacturing
requirements relating to non-laser optical
radiation safety
ISO 1463 - Metallic and oxide coatings - EN ISO 1463 -
Measurement of coating thickness -
Microscopical method
ISO 2178 - Non-magnetic coatings on magnetic EN ISO 2178 -
substrates - Measurement of coating
thickness - Magnetic method
ISO 2768-1 - General tolerances EN 22768-1 -
Part 1: Tolerances for linear and angular
dimensions without individual tolerance
indications
ISO 3744 - Acoustics - Determination of sound power EN ISO 3744 -
levels and sound energy levels of noise
sources using sound pressure -
Engineering methods for an essentially
free field over a reflecting plane
ISO 3864-2 - Graphical symbols - Safety colours and - -
safety signs
Part 2: Design principles for product safety
labels
ISO 3864-3 - Graphical symbols - Safety colours and - -
safety signs
Part 3: Design principles for graphical
symbols for use in safety signs
ISO 4871 1996 Acoustics - Declaration and verification of EN ISO 4871 2009
noise emission values of machinery and
equipment
ISO 5347 Series Methods for the calibration of vibration and - -
shock pick-ups
ISO 5349-1 - Mechanical vibration - Measurement and EN ISO 5349-1 -
evaluation of human exposure to hand-
transmitted vibration
Part 1: General requirements
13
---------------------- Page: 15 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
ISO 5349-2 - Mechanical vibration - Measurement and EN ISO 5349-2 -
evaluation of human exposure to hand-
transmitted vibration
Part 2: Practical guidance for
measurement at the workplace
ISO 7000 2012 Graphical symbols for use on equipment - - -
Registered symbols
ISO 7010 - Graphical symbols - Safety colours and EN ISO 7010 -
safety signs - Registered safety signs
ISO 7574-4 - Acoustics - Statistical methods for EN 27574-4 -
determining and verifying stated noise
emission values of machinery and
equipment
Part 4: Methods for stated values for
batches of machines
ISO 8041 - Human response to vibration - Measuring EN ISO 8041 -
instrumentation
ISO 9772 2012 Cellular plastics - Determination of - -
horizontal burning characteristics of small
specimens subjected to a small flame
ISO 11201 - Acoustics - Noise emitted by machinery EN ISO 11201 -
and equipment - Determination of
emission sound pressure levels at a work
station and at other specified positions in
an essentially free field over a reflecting
plane with negligible environmental
corrections
ISO 11203 - Acoustics - Noise emitted by machinery EN ISO 11203 -
and equipment - Determination of
emission sound pressure levels at a work
station and at other specified positions
from the sound power level
ISO/TR 11690-3 - Acoustics - Recommended practice for the EN ISO/TR 11690-3 -
design of low noise workplaces containing
machinery
Part 3: Sound propagation and noise
prediction in workrooms
ISO 12100 - Safety of machinery - General principles EN ISO 12100 -
for design - Risk assessment and risk
reduction
ISO 13849-1 - Safety of machinery - Safety-related parts EN ISO 13849-1 -
of control systems
Part 1: General principles for design
ISO 13850 - Safety of machinery - Emergency stop - EN ISO 13850 -
Principles for design
ISO 16063-1 - Methods for the calibration of vibration and - -
shock transducers
Part 1: Basic concepts
EN 12096 - Mechanical vibration - Declaration and - -
verification of vibration emission values
14
---------------------- Page: 16 ----------------------
SIST EN 62841-1:2015
EN 62841-1:2015 (E)
Publication Year Title EN/HD Year
ASTM B 258 Standard specification for standard - -
nominal diameters
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.