SIST EN ISO 8028:2018
(Main)Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:2017)
Rubber and/or plastics hoses and hose assemblies for airless paint spraying - Specification (ISO 8028:2017)
This document specifies the requirements for four types of hose and hose assemblies for use in airless
paint spraying. The four types are differentiated by burst pressure and operating temperature, and can
be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie Farbspritzen - Spezifikation (ISO 8028:2017)
Dieses Dokument legt die Anforderungen an vier Typen von Schläuchen und Schlauchleitungen für die Verwendung beim luftfreien Farbspritzen fest. Die vier Typen werden unterschieden durch Berstdruck und Betriebstemperatur, und können aus Gummi oder Kunststoffmaterialien oder einer Kombination aus Gummi und Kunststoff hergestellt sein.
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation sans air des peintures - Spécifications (ISO 8028:2017)
ISO 8028:2017 spécifie les exigences relatives à quatre types de tuyaux et flexibles utilisés dans la pulvérisation des peintures sans air. Les quatre types sont différenciés par la pression de rupture et la température d'utilisation, et peuvent être réalisés à partir de matériaux en caoutchouc ou en plastique, ou une combinaison de matériaux en caoutchouc et en plastique.
Gumene in/ali polimerne cevi ter cevni priključki za brezzračno brizganje barve - Specifikacija (ISO 8028:2017)
Ta dokument določa zahteve za štiri vrste cevi in cevnih priključkov za brezzračno brizganje barve. Te štiri vrste se ločujejo glede na razpočni tlak in delovno temperaturo, mogoče pa jih je izdelati iz gumenih ali plastičnih materialov ali s kombiniranjem gumenih in plastičnih materialov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2018
1DGRPHãþD
SIST EN ISO 8028:2001
*XPHQHLQDOLSROLPHUQHFHYLWHUFHYQLSULNOMXþNL]DEUH]]UDþQREUL]JDQMHEDUYH
6SHFLILNDFLMD ,62
Rubber and/or plastics hoses and hose assemblies for airless paint spraying -
Specification (ISO 8028:2017)
Gummi- und/oder Kunststoffschläuche und -schlauchleitungen für das luftfreie
Farbspritzen - Spezifikation (ISO 8028:2017)
Tuyaux et flexibles en caoutchouc et/ou en plastique pour pulvérisation sans air des
peintures - Spécifications (ISO 8028:2017)
Ta slovenski standard je istoveten z: EN ISO 8028:2018
ICS:
83.140.40 Gumene cevi Hoses
87.100 Oprema za nanašanje Paint coating equipment
premazov
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 8028
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2018
EUROPÄISCHE NORM
ICS 23.040.70; 87.100 Supersedes EN ISO 8028:2000
English Version
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying - Specification (ISO 8028:2017)
Tuyaux et flexibles en caoutchouc et/ou en plastique Gummi- und/oder Kunststoffschläuche und -
pour pulvérisation (AIRLESS) des peintures - schlauchleitungen für das luftfreie Farbspritzen -
Spécifications (ISO 8028:2017) Spezifikation (ISO 8028:2017)
This European Standard was approved by CEN on 26 November 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8028:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 8028:2018) has been prepared by Technical Committee ISO/TC 45/SC 1
“Rubber and plastics hoses and hose assemblies” in collaboration with Technical Committee
CEN/TC 218 “Rubber and plastics hoses and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2018, and conflicting national standards shall be
withdrawn at the latest by July 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8028:2000.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8028:2017 has been approved by CEN as EN ISO 8028:2018 without any modification.
INTERNATIONAL ISO
STANDARD 8028
Third edition
2017-11
Rubber and/or plastics hoses and
hose assemblies for airless paint
spraying — Specification
Tuyaux et flexibles en caoutchouc et/ou en plastique pour
pulvérisation (AIRLESS) des peintures — Spécifications
Reference number
ISO 8028:2017(E)
©
ISO 2017
ISO 8028:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 8028:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types of hose and hose assemblies . 2
5 Construction and materials . 2
6 Dimensions and tolerances . 2
7 Performance requirements for finished hose. 2
7.1 Adhesion requirements . 2
7.2 Ultraviolet resistance (plastics cover only) . 3
7.3 Resistance to ozone (rubber cover only). 3
8 Performance requirements for finished hose and hose assemblies .3
8.1 Hydrostatic requirements . 3
8.2 Impulse test requirements . 3
8.3 Electrical-continuity requirements . 3
9 Physical requirements of lining for hose only . 4
10 Frequency of testing . 4
11 Type testing. 4
12 Test report . 4
13 Marking . 4
14 Recommendations for packaging and storage . 5
Annex A (normative) Type test and routine test . 6
Annex B (informative) Test frequency for production acceptance tests .7
Bibliography . 8
ISO 8028:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.
This third edition cancels and replaces the second edition (ISO 8028:1999), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— the scope has been re-defined;
— the normative references have been updated accordingly;
— Clause 5 has been re-written to better define construction and materials;
— 7.1 has been re-written;
— the clause on electrical properties has been revised and updated to reflect changes in test methods;
— new Clauses 10 and 11 were added;
— a new Clause 14 was added;
— Annexes A and B have been revised to reflect hose and hose assembly tests.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 8028:2017(E)
Rubber and/or plastics hoses and hose assemblies for
airless paint spraying — Specification
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices.
1 Scope
This document specifies the requirements for four types of hose and hose assemblies for use in airless
paint spraying. The four types are differentiated by burst pressure and operating temperature, and can
be constructed from rubber or plastic materials, or a combination of rubber and plastic material.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817:2015, Rubber, vulcanized or thermoplastic — Determin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.