SIST EN ISO 11638:2022
(Main)Resilient floor coverings - Heterogeneous poly(vinyl chloride) flooring on foam - Specification (ISO 11638:2020, including corrected version 2021-09)
Resilient floor coverings - Heterogeneous poly(vinyl chloride) flooring on foam - Specification (ISO 11638:2020, including corrected version 2021-09)
This document specifies the characteristics of heterogeneous poly(vinyl chloride) flooring on foam, based on poly(vinyl chloride), and supplied in roll form or tile and plank. Such products can contain a transparent, non PVC factory finish.
To encourage the consumer to make an informed choice, this document includes a classification system, based on intensity of use, which shows where these floor coverings can be expected to give satisfactory service.
It also specifies requirements for marking.
Elastische Bodenbeläge - Heterogene Polyvinylchlorid-Bodenbeläge mit Schaumstoff - Spezifikation (ISO 11638:2020, korrigierte Fassung 2021‑09)
Revêtements de sol résilients - Revêtements de sol hétérogènes sur mousse à base de poly(chlorure de vinyle) - Spécification (ISO 11638:2020, y compris version corrigée 2021-09)
Le présent document spécifie les caractéristiques des revêtements de sol en poly(chlorure de vinyle) hétérogènes sur mousse, à base de poly(chlorure de vinyle), fournis sous forme de rouleaux, de dalles ou de lames. Ces produits peuvent comporter une finition en usine transparente non constituée de PVC.
Afin de permettre au consommateur de faire un choix éclairé, le présent document inclut un système de classification, fondé sur l'intensité d'utilisation, qui indique les cas dans lesquels l'on peut attendre que ces revêtements de sol assurent un service satisfaisant.
Elle spécifie également des exigences en matière de marquage.
Netekstilne talne obloge - Heterogene polivinilkloridne talne obloge na peni - Specifikacija (ISO 11638:2020, vključno s popravljeno različico 2021-09)
Ta dokument določa značilnosti heterogenih polivinilkloridnih talnih oblog na peni na osnovi polivinilklorida, dobavljenih v obliki zvitkov ali plošč in trakov. Takšni izdelki imajo lahko prosojen tovarniški zaključni sloj, ki ni iz PVC.
Da bi ta dokument potrošnike spodbujal k sprejemanju utemeljenih odločitev, vsebuje sistem razvrščanja na podlagi intenzivnosti uporabe, ki kaže, kje bi se te talne obloge lahko zadovoljivo uporabljale.
Vključuje tudi zahteve za označevanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11638:2022
01-september-2022
Nadomešča:
SIST EN 651:2011
Netekstilne talne obloge - Heterogene polivinilkloridne talne obloge na peni -
Specifikacija (ISO 11638:2020, vključno s popravljeno različico 2021-09)
Resilient floor coverings - Heterogeneous poly(vinyl chloride) flooring on foam -
Specification (ISO 11638:2020, including corrected version 2021-09)
Elastische Bodenbeläge - Heterogene Polyvinylchlorid-Bodenbeläge mit Schaumstoff -
Spezifikation (ISO 11638:2020, korrigierte Fassung 2021‑09)
Revêtements de sol résilients - Revêtements de sol hétérogènes sur mousse à base de
poly(chlorure de vinyle) - Spécification (ISO 11638:2020, y compris version corrigée
2021-09)
Ta slovenski standard je istoveten z: EN ISO 11638:2022
ICS:
97.150 Talne obloge Floor coverings
SIST EN ISO 11638:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11638:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 11638:2022
EN ISO 11638
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2022
EUROPÄISCHE NORM
ICS 97.150 Supersedes EN 651:2011
English Version
Resilient floor coverings - Heterogeneous poly(vinyl
chloride) flooring on foam - Specification (ISO
11638:2020, including corrected version 2021-09)
Revêtements de sol résilients - Revêtements de sol Elastische Bodenbeläge - Heterogene Polyvinylchlorid-
hétérogènes sur mousse à base de poly(chlorure de Bodenbeläge mit Schaumstoff - Spezifikation (ISO
vinyle) - Spécification (ISO 11638:2020, y compris 11638:2020, korrigierte Fassung 2021-09)
version corrigée 2021-09)
This European Standard was approved by CEN on 17 July 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11638:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11638:2022
EN ISO 11638:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11638:2022
EN ISO 11638:2022 (E)
European foreword
The text of ISO 11638:2020 has been prepared by Technical Committee ISO/TC 219 "Floor coverings” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 11638:2022
by Technical Committee CEN/TC 134 “Resilient, textile, laminate and modular mechanical locked floor
coverings” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2023, and conflicting national standards shall
be withdrawn at the latest by January 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 651:2011.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11638:2020 has been approved by CEN as EN ISO 11638:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11638:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 11638:2022
INTERNATIONAL ISO
STANDARD 11638
Second edition
2020-03
Corrected version
2021-09
Resilient floor coverings —
Heterogeneous poly(vinyl chloride)
flooring on foam — Specification
Revêtements de sol résilients — Revêtements de sol hétérogènes sur
mousse à base de poly(chlorure de vinyle) — Spécification
Reference number
ISO 11638:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 11638:2022
ISO 11638:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11638:2022
ISO 11638:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 2
4.1 Identification requirements. 2
4.2 General requirements . 3
4.3 Thickness of wear-layer requirements . 4
5 Classification requirements . 4
6 Marking . 8
Annex A (informative) Optional properties . 9
Bibliography .10
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11638:2022
ISO 11638:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 219, Floor coverings.
This second edition cancels and replaces the first edition (ISO 11638:2012), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— References to ISO 16906 and ISO 24342 have been added to Clause 2;
— in Table 2, a column for units has been added and requirements linked to permitted deviation for
tile/plank length and diameter of mandrel for flexibility have been amended;
— in Table 3, new requirements for seam strength have been added.
This corrected version of ISO 11638:2020 incorporates the following corrections:
— in Table 3, in the column "Indentation measured after 15 s of load application (walking comfort)",
the symbol ≤ has been changed to ≥.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11638:2022
INTERNATIONAL STANDARD ISO 11638:2020(E)
Resilient floor coverings — Heterogeneous poly(vinyl
chloride) flooring on foam — Specification
1 Scope
This document specifies the characteristics of heterogeneous poly(vinyl chloride) flooring on foam,
based on poly(vinyl chloride), and supplied in roll form or tile and plank. Such products can contain a
transparent, non PVC factory finish.
To encourage the consumer to make an informed choice, this document includes a classification system,
based on intensity of use, which shows where these floor coverings can be expected to give satisfactory
service.
It also specifies requirements for marking.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc
fading lamp test
ISO 4918, Resilient, textile and laminate floor coverings — Castor chair test
...
SLOVENSKI STANDARD
oSIST prEN ISO 11638:2022
01-maj-2022
Netekstilne talne obloge - Heterogene polivinilkloridne talne obloge na peni -
Specifikacija (ISO 11638:2020, vključno s popravljeno različico 2021-09)
Resilient floor coverings - Heterogeneous poly(vinyl chloride) flooring on foam -
Specification (ISO 11638:2020, including corrected version 2021-09)
Elastische Bodenbeläge - Heterogene Polyvinylchlorid-Bodenbeläge mit Schaumstoff -
Spezifikation (ISO 11638:2020, korrigierte Fassung 2021‑09)
Revêtements de sol résilients - Revêtements de sol hétérogènes sur mousse à base de
poly(chlorure de vinyle) - Spécification (ISO 11638:2020, y compris version corrigée
2021-09)
Ta slovenski standard je istoveten z: prEN ISO 11638
ICS:
97.150 Talne obloge Floor coverings
oSIST prEN ISO 11638:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 11638:2022
---------------------- Page: 2 ----------------------
oSIST prEN ISO 11638:2022
INTERNATIONAL ISO
STANDARD 11638
Second edition
2020-03
Corrected version
2021-09
Resilient floor coverings —
Heterogeneous poly(vinyl chloride)
flooring on foam — Specification
Revêtements de sol résilients — Revêtements de sol hétérogènes sur
mousse à base de poly(chlorure de vinyle) — Spécification
Reference number
ISO 11638:2020(E)
©
ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 11638:2022
ISO 11638:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 11638:2022
ISO 11638:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 2
4.1 Identification requirements. 2
4.2 General requirements . 3
4.3 Thickness of wear-layer requirements . 4
5 Classification requirements . 4
6 Marking . 8
Annex A (informative) Optional properties . 9
Bibliography .10
© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 11638:2022
ISO 11638:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www .iso .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 219, Floor coverings.
This second edition cancels and replaces the first edition (ISO 11638:2012), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— References to ISO 16906 and ISO 24342 have been added to Clause 2;
— in Table 2, a column for units has been added and requirements linked to permitted deviation for
tile/plank length and diameter of mandrel for flexibility have been amended;
— in Table 3, new requirements for seam strength have been added.
This corrected version of ISO 11638:2020 incorporates the following corrections:
— in Table 3, in the column "Indentation measured after 15 s of load application (walking comfort)",
the symbol ≤ has been changed to ≥.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 11638:2022
INTERNATIONAL STANDARD ISO 11638:2020(E)
Resilient floor coverings — Heterogeneous poly(vinyl
chloride) flooring on foam — Specification
1 Scope
This document specifies the characteristics of heterogeneous poly(vinyl chloride) flooring on foam,
based on poly(vinyl chloride), and supplied in roll form or tile and plank. Such products can contain a
transparent, non PVC factory finish.
To encourage the consumer to make an informed choice, this document includes a classification system,
based on intensity of use, which shows where these floor coverings can be expected to give satisfactory
service.
It also specifies requirements for marking.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc
fading lamp test
ISO 4918, Resilient, textile and laminate floor coverings — Castor chair test
ISO 10874, Resilient, textile and laminate floor coverings — Classification
ISO 16581, Resilient and laminate floor coverings — Determination of the effect of simulated movement of
a furniture leg
ISO 16906, Resilient floor coverings — Determination of seam strength
ISO 23997, Resilient floor coverings — Determination of mass per unit area
ISO 23999, Resilient floor coverings — Determination of dimensional stability and curling after exposure
to heat
ISO 24340, Resilient floor coverings — Determination of thickness of layers
ISO 24341, Resilient and textile floor coverings — Determination of length, width and straightness of sheet
ISO 24343-1, Resilient and laminate floor coverings — Determination of indentation and residual
indentation — Part 1: Residual indentation
ISO 24342, Resilient and textile floor-coverings — Determination of side length, edge straightness and
squareness of tiles
ISO 24344:2008, Resilient floor coverings — Determination of flexibility and deflection
ISO 24345, Resilient floor coverings — Determination of peel resistance
ISO 24346, Resilient floor coverings — Determination of overall thickness
ASTM F1515, Standard Test Method for Measuring Light Stability of Resilient Flooring by Color Change
© ISO 2020 – All rights reserved 1
---------------------- Page: 7 ----------------------
oSIST prEN ISO 11638:2022
ISO 11638:2020(E)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
heterogeneous flooring on foam
floor covering consisting of a wear layer and other solid layers on a foam backing
3.2
poly(vinyl chloride) flooring on foam
floor covering with surface layers which are produced using poly(vinyl chloride) as the binder
3.3
wear layer
layer of the floor covering directly exposed to wear
3.4
factory finish
transparent coating applied during the manufacture, usually not thicker than 0,03 mm
3.5
binder content
portion of the flooring
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.