SIST EN ISO 16120-4:2011
(Main)Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2011)
Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod for special applications (ISO 16120-4:2011)
This European Standard defines rod with improved characteristics intended for drawing and/or cold rolling.
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 4: Besondere Anforderungen an Walzdraht für Sonderanwendungen (ISO 16120-4:2011)
Dieser Teil der ISO 16120 gilt für Walzdraht mit erhöhten Anforderungen zum Ziehen und/oder Kaltwalzen.
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 4: Exigences spécifiques au fil-machine pour applications spéciales (ISO 16120-4:2011)
L'ISO 16120-4:2011 est applicable au fil-machine en acier dont les caractéristiques ont été améliorées, destiné au tréfilage et/ou au laminage à froid.
Vroče valjana žica iz nelegiranega jekla za vlečenje in/ali hladno valjanje - 4. del: Posebne zahteve za žico za posebne namene (ISO 16120-4:2011)
Ta evropski standard opredeljuje žico z izboljšanimi lastnostmi, namenjeno vlečenju in/ali hladnemu valjanju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16120-4:2011
01-november-2011
1DGRPHãþD
SIST EN 10016-4:1997
9URþHYDOMDQDåLFDL]QHOHJLUDQHJDMHNOD]DYOHþHQMHLQDOLKODGQRYDOMDQMHGHO
3RVHEQH]DKWHYH]DåLFR]DSRVHEQHQDPHQH,62
Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod
for special applications (ISO 16120-4:2011)
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 4: Besondere Anforderungen an
Walzdraht für Sonderanwendungen (ISO 16120-4:2011)
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 4: Exigences
spécifiques au fil-machine pour applications spéciales (ISO 16120-4:2011)
Ta slovenski standard je istoveten z: EN ISO 16120-4:2011
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
SIST EN ISO 16120-4:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16120-4:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 16120-4:2011
EUROPEAN STANDARD
EN ISO 16120-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 77.140.60 Supersedes EN 10016-4:1994
English Version
Non-alloy steel wire rod for conversion to wire - Part 4: Specific
requirements for wire rod for special applications (ISO 16120-
4:2011)
Fil-machine en acier non allié destiné à la fabrication de fils Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 4:
- Partie 4: Exigences spécifiques au fil-machine pour Besondere Anforderungen an Walzdraht für
applications spéciales (ISO 16120-4:2011) Sonderanwendungen (ISO 16120-4:2011)
This European Standard was approved by CEN on 30 June 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16120-4:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16120-4:2011
EN ISO 16120-4:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16120-4:2011
EN ISO 16120-4:2011 (E)
Foreword
This document (EN ISO 16120-4:2011) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 106 “Wire rod and wires” the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at
the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10016-4:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 16120-4:2011 has been approved by CEN as a EN ISO 16120-4:2011 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16120-4:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 16120-4:2011
INTERNATIONAL ISO
STANDARD 16120-4
Second edition
2011-07-01
Non-alloy steel wire rod for conversion to
wire —
Part 4:
Specific requirements for wire rod for
special applications
Fil-machine en acier non allié destiné à la fabrication de fils —
Partie 4: Exigences spécifiques au fil-machine pour applications
spéciales
Reference number
ISO 16120-4:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 16120-4:2011
ISO 16120-4:2011(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 16120-4:2011
ISO 16120-4:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Designation .2
4 Requirements.2
4.1 General .2
4.2 Chemical composition and mechanical properties .2
4.3 Internal soundness and surface quality.4
4.4 Depth of surface discontinuities.4
4.5 Depth of decarburization .4
4.6 Non-metallic inclusions .5
4.7 Core segregation .5
4.8 Tensile strength.6
4.9 Scale characteristics.6
4.10 Mechanical damage.6
4.11 Microstructure .6
Annex A (informative) Steel designations in accordance with ISO 16120-4 and designation of
comparable steel grades in national or regional standards .7
Bibliography.9
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 16120-4:2011
ISO 16120-4:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16120-4 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 17, Steel wire rod
and wire products.
This second edition cancels and replaces the first edition (ISO 16120-4:2001), which has been technically
revised.
ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rod for conversion to
wire:
⎯ Part 1: General requirements
⎯ Part 2: Specific requirements for general-purpose wire rod
⎯ Part 3: Specific requirements for rimmed and rimmed substitute, low-carbon steel wire rod
⎯ Part 4: Specific requirements for wire rod for special applications
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 16120-4:2011
INTERNATIONAL STANDARD ISO 16120-4:2011(E)
Non-alloy steel wire rod for conversion to wire —
Part 4:
Specific requirements for wire rod for special applications
1 Scope
This part of ISO 16120 is applicable to steel wire rod with improved characteristics intended for drawing and/or
cold rolling.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on
chemical composition
ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main
quality classes and main property or application characteristics
ISO/TS 4949, Steel names based on letter symbols
ISO 4967, Steel — Determination of content of nonmetallic inclusions — Micrographic method using standard
diagrams
ISO 16120-1:2011, Non-alloy steel wire rod for conversion to wire — Part 1: General requirements
ISO 16120-2:2011, Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for
general-purpose wire rod
ASTM E45, Standard Test Methods for Determining the Inclusion Content of Steel
© ISO 2011 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 16120-4:2011
ISO 16120-4:2011(E)
3 Designation
In the designation C##D2, “C” means non-alloy steel (see ISO/TS 4949); ## is the indicative average content
of carbon;. “D” signifies that it is for wire-drawing; “2” means wire rod for special applications.
If steels are ordered according to the chemical composition, ## means that values are to be inserted by the
purchaser according to the steel names as designated in Table 1, first column.
Steels can also be ordered according to tensile strength. The mid-point of the required ultimate tensile
strength (UTS) range shall be indicated as a suffix to the grade designation, e.g. C##D2 – 1020, where the
required mid-point of the UTS is 1 020 MPa. “##” means “to be left blank” since the carbon content is at the
discretion of the supplying mill, and the supplying mill indicates the exact number of ## based on the grade
designation until shipment. See Table 1 of ISO 16120-2:2011 for the grade designation.
4 Requirements
4.1 General
For the general requirements, see ISO 16120-1.
4.2 Chemical composition and mechanical properties
For heat analysis, the values shown in Table 1 shall apply. If product analysis is required, the permissible
deviations of the product analysis relative to the specified value of the heat analysis are given in Table 2.
2 © ISO 2011 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 16120-4:2011
ISO 16120-4:2011(E
...
SLOVENSKI STANDARD
oSIST prEN ISO 16120-4:2010
01-februar-2010
9URþHYDOMDQDåLFDL]QHOHJLUDQHJDMHNOD]DYOHþHQMHLQDOLKODGQRYDOMDQMHGHO
3RVHEQH]DKWHYH]DåLFR]DSRVHEQHQDPHQH,62',6
Non-alloy steel wire rod for conversion to wire - Part 4: Specific requirements for wire rod
for special applications (ISO/DIS 16120-4:2009)
Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 4: Besondere Anforderungen an
Walzdraht für Sonderanwendungen (ISO/DIS 16120-4:2009)
Fil-machine en acier non allié destiné à la fabrication de fils - Partie 4: Exigences
spécifiques au fil-machine pour applications spéciales (ISO/DIS 16120-4:2009)
Ta slovenski standard je istoveten z: prEN ISO 16120-4
ICS:
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
oSIST prEN ISO 16120-4:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 16120-4:2010
---------------------- Page: 2 ----------------------
oSIST prEN ISO 16120-4:2010
EUROPEAN STANDARD
DRAFT
prEN ISO 16120-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2009
ICS 77.140.60 Will supersede EN 10016-4:1994
English Version
Non-alloy steel wire rod for conversion to wire - Part 4: Specific
requirements for wire rod for special applications (ISO/DIS
16120-4:2009)
Fil-machine en acier non allié destiné à la fabrication de fils Walzdraht aus unlegiertem Stahl zum Ziehen - Teil 4:
- Partie 4: Exigences spécifiques au fil-machine pour Besondere Anforderungen an Walzdraht für
applications spéciales (ISO/DIS 16120-4:2009) Sonderanwendungen (ISO/DIS 16120-4:2009)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
ECISS/TC 15.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 16120-4:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 16120-4:2010
prEN ISO 16120-4:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 16120-4:2010
prEN ISO 16120-4:2009 (E)
Foreword
This document (prEN ISO 16120-4:2009) has been prepared by Technical Committee ISO/TC 17 "Steel" in
collaboration with Technical Committee ECISS/TC 15 “Wire-rod - Qualities, dimensions, tolerances and
specific tests” the secretariat of which is held by UNI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN 10016-4:1994.
Endorsement notice
The text of ISO/DIS 16120-4:2009 has been approved by CEN as a prEN ISO 16120-4:2009 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 16120-4:2010
---------------------- Page: 6 ----------------------
oSIST prEN ISO 16120-4:2010
DRAFT INTERNATIONAL STANDARD ISO/DIS 16120-4
ISO/TC 17/SC 17 Secretariat: SAC
Voting begins on: Voting terminates on:
2009-12-03 2010-05-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Non-alloy steel wire rod for conversion to wire —
Part 4:
Specific requirements for wire rod for special applications
Fil-machine en acier non allié destiné à la fabrication de fils —
Partie 4: Exigences spécifiques au fil-machine pour applications spéciales
[Revision of first edition (ISO 16120-4:2001)]
ICS 77.140.60
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2009
---------------------- Page: 7 ----------------------
oSIST prEN ISO 16120-4:2010
ISO/DIS 16120-4
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2009 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 16120-4:2010
ISO/DIS 16120-4
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Designation.1
4 Requirements.2
4.1 General .2
4.2 Chemical composition and mechanical properties .2
4.3 Internal soundness and surface quality.3
4.4 Depth of surface discontinuities.3
4.5 Depth of decarburization .4
4.6 Non-metallic inclusions .4
4.7 Core segregation.5
4.8 Tensile strength.5
4.9 Scale characteristics.5
4.10 Mechanical Damage .5
4.11 Microstructure .6
Bibliography.7
© ISO 2002 – All rights reserved iii
DRAFT 2009
---------------------- Page: 9 ----------------------
oSIST prEN ISO 16120-4:2010
ISO/DIS 16120-4
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 16120-4 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee
SC 17, Steel wire rod and wire products.
This first edition of ISO 16120-4, together with parts 1,2 and 3 cancels and replaces ISO 8457-2:1989 which
has been technically revised and augmented.
ISO 16120 consists of the following parts, under the general title Non-alloy steel wire rods for conversion to
wire:
- Part 1: General requirements
- Part 2: Specific requirements for general purpose wire rod
- Part 3 Specific requirements for rimmed and rimmed substitute low carbon steel wire rod
- Part 4 Specific requirements for wire rod for special applications
iv © ISO 2002 – All rights reserved
DRAFT 2009
---------------------- Page: 10 ----------------------
oSIST prEN ISO 16120-4:2010
DRAFT INTERNATIONAL STANDARD ISO/DIS 16120-4
Non-alloy steel wire rod for conversion to wire —
Part 4:
Specific requirements for wire rod for special applications
1
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.