iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 61803:2001

(Main)

Determination of power losses in high-voltage direct current (HVDC) converter stations

Determination of power losses in high-voltage direct current (HVDC) converter stations

Applies to all line-commutated high-voltage direct current (HVDC) converter stations used for power exchange in utility systems. This standard presimes the use of 12-puls thyristor converters but can, with due care, also be used for 6-pulse thyristor converters.

Bestimmung der Leistungsverluste in Hochspannungsgleichstrom- (HGÜ-)Stromrichterstationen

Détermination des pertes en puissance dans les postes de conversion en courant continu à haute tension (CCHT)

S'applique à tous les postes de conversion en courant continu à haute tnesion (CCHT), commutés par le réseau, et utilisés pour l'échange de puissance dans des systèmes de distribution d'énergie. Présuppose l'utilisation de convertisseurs à thyristors à 12 impulsions mais peut également s'appliquer à des convertisseurs à thyristors à 6 impulsions. Décrit un ensemble de procédures types permettant de déterminer l'ensemble des pertes d'un poste de conversion à CCHT. Les procédures recouvrent toutes les pièces, à l'exception des compensateurs synchrones ou des compensateurs var statiques et considèrent les pertes en fonctionnement à vide et les pertes en fonctionnement ainsi que leurs méthodes de calcul utilisant, dans la mesure du possible, des paramètres mesurés.

Determination of power losses in high-voltage direct current (HVDC) converter stations (IEC 61803:1999)

Velja za vse vodovno komutirane visokonapetostne enosmerne (HVDC) pretvornike, ki se uporabljajo za izmenjavo električne energije v javnih sistemih. Ta standard predvideva uporabo 12-pulznih tiristorksih pretvornikov, vendar se lahko uporablja tudi za 6-pulzne tiristorske pretvornike ob ustrezni previdnosti.

General Information

Status
Withdrawn
Publication Date
31-May-2001
Withdrawal Date
11-Oct-2023
ICS
29.200 - Rectifiers. Convertors. Stabilized power supply
Technical Committee
MOV - Measuring equipment for electromagnetic quantities
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
09-Oct-2023
Due Date
01-Nov-2023
Completion Date
12-Oct-2023
Ref Project
EN 61803:1999 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters

Relations

Replaced By
SIST EN IEC 61803:2021 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters (IEC 61803:2020)
Effective Date
08-Dec-2020
Amended By
SIST EN 61803:2001/A2:2016 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters (IEC 61803:1999/A2:2016)
Effective Date
24-Mar-2015
Amended By
SIST EN 61803:2001/A1:2011 - Determination of power losses in high-voltage direct current (HVDC) converter stations with line-commutated converters (IEC 61803:1999/A1:2010)
Effective Date
01-Feb-2011

Buy Standard

EN 61803:2001EN 61803:2001
PreviousNext
Standard
EN 61803:2001
English language
36 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61803:2001
01-junij-2001
Determination of power losses in high-voltage direct current (HVDC) converter
stations (IEC 61803:1999)
Determination of power losses in high-voltage direct current (HVDC) converter stations
Bestimmung der Leistungsverluste in Hochspannungsgleichstrom- (HGÜ-)
Stromrichterstationen
Détermination des pertes en puissance dans les postes de conversion en courant
continu à haute tension (CCHT)
Ta slovenski standard je istoveten z: EN 61803:1999
ICS:
29.200 8VPHUQLNL3UHWYRUQLNL Rectifiers. Convertors.
6WDELOL]LUDQRHOHNWULþQR Stabilized power supply
QDSDMDQMH
SIST EN 61803:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61803:2001

---------------------- Page: 2 ----------------------

SIST EN 61803:2001

---------------------- Page: 3 ----------------------

SIST EN 61803:2001

---------------------- Page: 4 ----------------------

SIST EN 61803:2001

---------------------- Page: 5 ----------------------

SIST EN 61803:2001

---------------------- Page: 6 ----------------------

SIST EN 61803:2001

---------------------- Page: 7 ----------------------

SIST EN 61803:2001

---------------------- Page: 8 ----------------------

SIST EN 61803:2001

---------------------- Page: 9 ----------------------

SIST EN 61803:2001

---------------------- Page: 10 ----------------------

SIST EN 61803:2001

---------------------- Page: 11 ----------------------

SIST EN 61803:2001

---------------------- Page: 12 ----------------------

SIST EN 61803:2001

---------------------- Page: 13 ----------------------

SIST EN 61803:2001

---------------------- Page: 14 ----------------------

SIST EN 61803:2001

---------------------- Page: 15 ----------------------

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 62927:2018/A1:2023(Amendment)
Amendment 1 - Voltage sourced converter (VSC) valves for static synchronous compensator (STATCOM) - Electrical testing (IEC 62927:2017/AMD1:2023)
EN 62927:2017/A1:2023
  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60700-3:2023(Main)
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 3: Essential ratings (limiting values) and characteristics
EN IEC 60700-3:2023

This part of IEC 60700 specifies the service conditions, the definitions of essential ratings and characteristics of thyristor valves utilized in line commutated converters with three-phase bridge connections to realize the conversion from AC to DC and vice versa for high voltage direct current (HVDC) power transmission applications. It is applicable for air insulated, liquid cooled and indoor thyristor valves.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62751-1:2014/A2:2022(Amendment)
Power losses in voltage sourced converter (VSC) valves for high-voltage direct current (HVDC) systems - Part 1: General requirements (IEC 62751-1:2014/AMD2:2022)
EN 62751-1:2014/A2:2022
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60700-1:2015/A1:2022(Amendment)
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 1: Electrical testing (IEC 60700-1:2015/AMD1:2021)
EN 60700-1:2015/A1:2021

No scope available

  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 50171:2022(Main)
Central safety power supply systems
EN 50171:2021

This European Standard specifies the general requirements for central power supply systems for an independent energy supply to essential safety equipment. This standard covers systems that are permanently connected to AC supply voltages not exceeding 1 000 V and use batteries as an alternative power source.
Central safety power supply systems are intended to ensure energy supply to emergency escape lighting in the event of normal supply failure and may be suitable for energising other essential safety equipment, for example:
- electric circuits of automatic fire extinguishing installations;
- paging systems and signalling safety installations;
- smoke extraction equipment;
- carbon monoxide warning systems;
- special safety installations related to specific buildings, e.g. high-risk areas.
The power supply of CPS should be dedicated only to the essential safety equipment, and not for other typeof loads such as general purpose IT or industrial systems etc.
Combinations of the aforementioned safety equipment types and / or non-safety equipment loads are permitted together on the same central safety power supply system providing the availability for safety equipment loads is not impaired. A fault occurring in a circuit should not cause the interruption in any other circuit used to supply safety equipment.
Schematic representations of typical central safety power supply equipment are depicted in Clause 4.
Power supply systems for fire alarm equipment that are covered by EN 54 (series) are excluded.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60700-2:2017/A1:2021(Amendment)
Thyristor valves for high voltage direct current (HVDC) power transmission - Part 2: Terminology (IEC 60700-2:2016/AMD1:2021)
EN 60700-2:2016/A1:2021

No scope available

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 62040-3:2021(Main)
Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements (IEC 62040-3:2021)
EN IEC 62040-3:2021

IEC 62040-3:2011 applies to movable, stationary and fixed electronic uninterruptible power systems (UPS) that deliver single or three phase fixed frequency a.c. output voltage not exceeding 1 000 V a.c. and that incorporate an energy storage system, generally connected through a d.c. link. This standard is intended to specify performance and test requirements of a complete UPS and not of individual UPS functional units. The individual UPS functional units are dealt with in IEC publications referred to in the bibliography that apply so far that they are not in contradiction with this standard. The primary function of the UPS covered by this standard is to ensure continuity of an a.c. power source. The UPS may also serve to improve the quality of the power source by keeping it within specified characteristics. UPS have been developed over a wide range of power, from less than hundred watts to several megawatts, to meet requirements for availability and quality of power to a variety of loads. Refer to Annexes A and B for information on typical UPS configurations and topologies. This standard also covers UPS test and performance when power switches form integral part of a UPS and are associated with its output. Included are interrupters, bypass switches, isolating switches, and tie switches. These switches interact with other functional units of the UPS to maintain continuity of load power. This standard does not cover:
- conventional a.c. input and output distribution boards or d.c. boards and their associated switches (e.g. switches for batteries, rectifier output or inverter input);
- stand-alone static transfer systems covered by IEC 62310-3;
- systems wherein the output voltage is derived from a rotating machine.
NOTE 1  This standard recognises that power availability to information technology (IT) equipment represents a major UPS application. The UPS output characteristics specified in this standard are therefore also aimed at ensuring compatibility with the requirements of IT equipment. This, subject any limitation stated in the manufacturer's declaration, includes requirements for steady state and transient voltage variation as well as for the supply of both linear and non-linear load characteristics of IT equipment.
NOTE 2  Test loads specified in this standard simulate both linear and non-linear load characteristics. Their use is prescribed with the objective of verifying design and performance, as declared by the manufacturer, and also of minimising any complexity and energy consumption during the tests.
NOTE 3  This standard is aimed at 50 Hz and 60 Hz applications but does not exclude other frequency applications within the domain of IEC 60196. This is subject to an agreement between manufacturer and purchase in respect to any particular requirements arising.
NOTE 4  Single phase and three-phase voltage UPS covered by this standard include without limitation UPS supplying single-phase, two-wire; single-phase, three-wire; two-phase, three-wire, three-phase, three-wire and three-phase, four-wire loads.
This second edition cancels and replaces first edition published in 1999 and constitutes a technical revision. The significant technical changes are:
- reference test load - definition and application revised (3.3.5 and 6.1.1.3);
- test schedule - presented as a single table grouped by revised type and routine tests (see 6.1.6, Table 3);
- dynamic output voltage performance characteristics - guidance to measure - addition (Annex H);
- UPS efficiency - requirements and methods of measure - addition (Annexes I and J);
- functional availa

  • Standard
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61800-5-1:2008/A11:2021(Amendment)
Adjustable speed electrical power drive systems - Part 5-1: Safety requirements - Electrical, thermal and energy
EN 61800-5-1:2007/A11:2021

2020-12-03: This AMD will revise Annex ZZ and allow citation of EN 61800-5-1:2007 & its A1:2017

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61800-2:2021(Main)
Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for adjustable speed AC power drive systems (IEC 61800-2:2021)
EN IEC 61800-2:2021

IEC 61800-2:2015 applies to adjustable speed electric a.c. power drive systems, which include semiconductor power conversion and the means for their control, protection, monitoring, measurement and the a.c. motors. It applies to adjustable speed electric power drive systems intended to feed a.c. motors from a BDM connected to line-to-line voltages up to and including 1 kV a.c. 50 Hz or 60 Hz and/or voltages up to and including 1,5 kV d.c. input side.
NOTE 1 Adjustable speed electric a.c. power drive systems intended to feed a.c. motors, and with rated converter input voltages above 1 000 V a.c. are covered by IEC 61800-4.
NOTE 2 Adjustable speed electric d.c. power drive systems intended to feed d.c. motors are covered by IEC 61800-1.
NOTE 3 For adjustable speed electric a.c. power drive systems having series-connected electronic power converter sections, the line-to-line voltage is the sum of the series connected input voltages.
Traction applications and electric vehicles are excluded from the scope of this standard. IEC 61800-2:2015 is intended to define the following aspects of an a.c. power drive system (PDS):
- principal parts of the PDS;
- ratings and performance;
- specifications for the environment in which the PDS is intended to be installed and operated;
- other specifications which might be applicable when specifying a complete PDS.
This standard provides minimum requirements, which may be used for the development of a specification between customer and manufacturer. This edition includes the following significant technical changes with respect to the previous edition.
a) Clause 1 (Scope) has been updated,
b) Clause 2 (Normative references) has been updated,
c) Clause 3 (Definitions) has been updated including fundamental definitions to be used across the IEC 61800 series of standards,
d) Clause 4 has been updated with respect to:
1) description of the basic topology for BDM/CDM/PDS (4.2);
2) ratings and performance (4.3 and 4.4);
3) reference to applicable standards within the IEC 61800 series with respect to EMC (IEC 61800-3), Electrical safety (IEC 61800-5-1), Functional safety (IEC 61800-5-2), Load duty aspects (IEC TR 61800-6), Communication profiles (IEC 61800-7 series) and Power interface voltage (IEC TS 61800-8) to avoid conflicting requirements (4.5, 4.6, 4.7, 4.10, 4.11, 4.12);
4) update of requirement for ECO design (4.8);
5) update of requirement for environmental evaluation (4.9);
6) implementation of requirement for explosive atmosphere (4.13).
e) Clause 5 has been updated with test requirement in order to provide a clear link between design requirement and test requirement.
f) Clause 6 has been updated to harmonize the marking and documentation requirement within the IEC 61800 series.
g) Existing Annexes A to G have been deleted and replaced with new Annexes A to C.

  • Standard
    121 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61800-1:2021(Main)
Adjustable speed electrical power drive systems - Part 1: General requirements - Rating specifications for low voltage adjustable speed DC power drive systems (IEC 61800-1:2021)
EN IEC 61800-1:2021

This part of IEC 61800 applies to adjustable speed electric DC power drive systems, which
include semiconductor power conversion and the means for their control, protection, monitoring,
measurement and the DC motors.
It applies to adjustable speed electric power drive systems intended to feed DC motors from a
BDM/CDM connected to line-to-line voltages up to and including 1 kV AC 50 Hz or 60 Hz and/or
voltages up to and including 1,5 kV DC input side.
NOTE 1 Adjustable speed electric AC power drive systems intended to feed AC motors are covered by
IEC 61800-2.
NOTE 2 This document can be used as a reference for adjustable speed electric power drive systems, intended to
feed DC motors from a BDM/CDM connected to line-to-line voltages up to and including 1,5 kV AC, 50 Hz or 60 Hz
and/or voltages up to and including 2,25 kV DC input side.
Traction applications and electric vehicles are excluded from the scope of this document.
This document is intended to define the following aspects of a DC power drive system (PDS):
• principal parts of the PDS;
• ratings and performance;
• specifications for the environment in which the PDS is intended to be installed and operated;
• other specifications which might be applicable when specifying a complete PDS.
This document provides minimum requirements, which may be used for the development of a
specification between customer and manufacturer.
Compliance with this document is possible only when each topic of this document is individually
specified by the customer developing specifications or by product standard committees
developing product standards.
For some aspects which are covered by specific PDS product standards in the IEC 61800 series,
this document provides a short introduction and reference to detailed requirements in these
product standards.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day