Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys, wood, other materials (ISO 12215-3:2002)

This part of ISO 12215 specifies requirements for materials intended for use in the construction of the hull,
superstructure and appendages, in particular:
— weldable normal and higher strength hot-rolled steel plates, wide flats, sections and bars;
— austenitic stainless steels, fabricated in the form of plates or profiles;
— wrought aluminium alloys fabricated as plates, sections and extruded profiles;
— wood in the form of solid timber, plywood or veneer;
— other suitable materials.
NOTE 1 Other materials may be used in the construction of small craft if adequate suitability and durability for the intended
purpose can be demonstrated.
This part of ISO 12215 applies to small craft with a length hull (LH) according to ISO 8666 of up to 24 m.
NOTE 2 The underlying reason for preparing this part of ISO 12215 is that the choice of materials for the construction of a
small craft has a significant influence on short-term and long-term durability under the expected loads and environmental
conditions.

Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 3: Werkstoffe: Stahl, Aluminiumlegierungen, Holz, andere Werkstoffe (ISO 12215-3:2002)

Petits navires - Construction de coques et échantillons - Partie 3: Matériaux: Acier, alliages d'aluminium, bois, autres matériaux (ISO 12215-3:2002)

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 3. del: Materiali: jeklo, aluminijeve zlitine, les, drugi materiali (ISO 12215-3:2002)

Ta del standarda ISO 12215 določa zahteve za materiale, namenjene za uporabo pri izdelavi trupa, nadkonstrukcije in dodatkov, zlasti za:
– varivno običajno in vroče valjano pločevino, široke plošče, profile in palice;
– avstenitna nerjavna jekla, izdelana v obliki plošč ali profilov;
– gnetene aluminijeve zlitine, izdelane kot plošče, profili in ekstrudirani profili;
– les v obliki masivnega lesa, vezanih plošč ali furnirja;
– druge ustrezne materiale.
OPOMBA 1: Pri konstrukciji malih plovil se lahko uporabljajo drugi materiali, če je mogoče dokazati primerno ustreznost in trajnost za predvideni namen.
Ta del standarda ISO 12215 se uporablja za mala plovila z dolžino trupa (LH) do 24 m v skladu s standardom ISO 8666.
OPOMBA 2: Osnovni razlog za pripravo tega dela standarda ISO 12215 je, da izbira materialov za konstrukcijo malega plovila pomembno vpliva na kratkoročno in dolgoročno vzdržljivost v skladu s pričakovanimi obremenitvami ter okoljskimi pogoji.

General Information

Status
Published
Public Enquiry End Date
14-Mar-2018
Publication Date
08-Oct-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Oct-2018
Due Date
10-Dec-2018
Completion Date
09-Oct-2018

RELATIONS

Buy Standard

Standard
SIST EN ISO 12215-3:2018
English language
18 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 12215-3:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 12215-3:2002

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 3. del: Materiali: jeklo,

aluminijeve zlitine, les, drugi materiali (ISO 12215-3:2002)

Small craft - Hull construction and scantlings - Part 3: Materials: Steel, aluminium alloys,

wood, other materials (ISO 12215-3:2002)
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 3: Werkstoffe:
Stahl, Aluminiumlegierungen, Holz, andere Werkstoffe (ISO 12215-3:2002)

Petits navires - Construction de coques et échantillons - Partie 3: Matériaux: Acier,

alliages d'aluminium, bois, autres matériaux (ISO 12215-3:2002)
Ta slovenski standard je istoveten z: EN ISO 12215-3:2018
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
SIST EN ISO 12215-3:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 12215-3:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 12215-3:2018
EN ISO 12215-3
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 12215-3:2002
English Version
Small craft - Hull construction and scantlings - Part 3:
Materials: Steel, aluminium alloys, wood, other materials
(ISO 12215-3:2002)

Petits navires - Construction de coques et échantillons - Kleine Wasserfahrzeuge - Rumpfbauweise und

Partie 3: Matériaux: Acier, alliages d'aluminium, bois, Dimensionierung - Teil 3: Werkstoffe: Stahl,

autres matériaux (ISO 12215-3:2002) Aluminiumlegierungen, Holz, andere Werkstoffe (ISO

12215-3:2002)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-3:2018 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 12215-3:2018
EN ISO 12215-3:2018 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

Annex ZA (informative) Relationship between this European Standard and the Essential

Requirements of Directive 2013/53/EU aimed to be covered ....................................................... 4

---------------------- Page: 4 ----------------------
SIST EN ISO 12215-3:2018
EN ISO 12215-3:2018 (E)
European foreword

The text of ISO 12215-3:2002 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the

International Organization for Standardization (ISO) and has been taken over as EN ISO 12215-3:2018.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be

withdrawn at the latest by March 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 12215-3:2002.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.

For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of

this document.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

the United Kingdom.
Endorsement notice

The text of ISO 12215-3:2002 has been approved by CEN as EN ISO 12215-3:2018 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 12215-3:2018
EN ISO 12215-3:2018 (E)
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered

This European standard has been prepared under a Commission’s standardization request M/542

C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive

2013/53/EU.

Once this standard is cited in the Official Journal of the European Union under that Directive, compliance

with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of

this standard, a presumption of conformity with the corresponding Essential Requirements of that

Directive and associated EFTA regulations.

Table ZA.1 — Correspondence between this European Standard and Annex I of Directive

2013/53/EU
Essential Clause(s)/sub- Remarks/Notes
Requirements of clause(s) of
Directive this EN
2013/53/EU

Annex I, Part A, 3.1 - All clauses This standard addresses the essential requirement set out in

Structure Annex I, Part A, 3.1 in respect of the requirements for steel,
aluminium alloys, wood and other materials used for the
construction of watercraft with the exception of thermosetting
resins, glass fibre reinforcement and reference laminate which
are addressed separately by part 1 of this standard series.
Annex I, Part A, 2.5 – 8, Annex A
Owner’s Manual

WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European

Standard is maintained in the list published in the Official Journal of the European Union. Users of this

standard should consult frequently the latest list published in the Official Journal of the European Union.

WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of

this standard.
---------------------- Page: 6 ----------------------
SIST EN ISO 12215-3:2018
INTERNATIONAL ISO
STANDARD 12215-3
First edition
2002-05-01
Small craft — Hull construction
and scantlings —
Part 3:
Materials: Steel, aluminium alloys, wood,
other materials
Petits navires — Construction de coques et échantillons —
Partie 3: Matériaux: Acier, alliages d'aluminium, bois, autres matériaux
Reference number
ISO 12215-3:2002(E)
ISO 2002
---------------------- Page: 7 ----------------------
SIST EN ISO 12215-3:2018
ISO 12215-3:2002(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not

be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this

file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this

area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters

were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event

that a problem relating to it is found, please inform the Central Secretariat at the address given below.

© ISO 2002

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic

or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body

in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 12215-3:2018
ISO 12215-3:2002(E)
Contents Page

Foreword.....................................................................................................................................................................iv

1 Scope..............................................................................................................................................................1

2 Normative references....................................................................................................................................1

3 Terms and definitions ...................................................................................................................................1

4 Requirements for metal.................................................................................................................................2

5 Requirements for wood.................................................................................................................................4

6 Requirements for other materials ................................................................................................................6

7 Documentation...............................................................................................................................................6

8 Owner’s manual.............................................................................................................................................7

Annex A (normative) Information to be provided in the owner's manual .............................................................8

Bibliography................................................................................................................................................................9

© ISO 2002 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 12215-3:2018
ISO 12215-3:2002(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO

member bodies). The work of preparing International Standards is normally carried out through ISO technical

committees. Each member body interested in a subject for which a technical committee has been established has

the right to be represented on that committee. International organizations, governmental and non-governmental, in

liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical

Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.

The main task of technical committees is to prepare International Standards. Draft International Standards adopted

by the technical committees are circulated to the member bodies for voting. Publication as an International

Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this part of ISO 12215 may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 12215-3 was prepared by Technical Committee ISO/TC 188, Small craft.

ISO 12215 consists of the following parts, under the general title Small craft — Hull construction and scantlings:

— Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate

— Part 2: Materials: Core materials for sandwich construction, embedded materials

— Part 3: Materials: Steel, aluminium alloys, wood, other materials
— Part 4: Workshop and manufacturing
— Part 5: Design pressures, design stresses, scantling determination
— Part 6: Structural arrangements and details
Annex A forms a normative part of this part of ISO 12215.
iv © ISO 2002 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 12215-3:2018
INTERNATIONAL STANDARD ISO 12215-3:2002(E)
Small craft — Hull construction and scantlings —
Part 3:
Materials: Steel, aluminium alloys, wood, other materials
1 Scope

This part of ISO 12215 specifies requirements for materials intended for use in the construction of the hull,

superstructure and appendages, in particular:

— weldable normal and higher strength hot-rolled steel plates, wide flats, sections and bars;

— austenitic stainless steels, fabricated in the form of plates or profiles;
— wrought aluminium alloys fabricated as plates, sections and extruded profiles;
— wood in the form of solid timber, plywood or veneer;
— other suitable materials.

NOTE 1 Other materials may be used in the construction of small craft if adequate suitability and durability for the intended

purpose can be demonstrated.

This part of ISO 12215 applies to small craft with a length hull (L ) according to ISO 8666 of up to 24 m.

NOTE 2 The underlying reason for preparing this part of ISO 12215 is that the choice of materials for the construction of a

small craft has a significant influence on short-term and long-term durability under the expected loads and environmental

conditions.
2 Normative references

The following normative documents contain provisions which, through reference in this text, constitute provisions of

this part of ISO 12215. For dated references, subsequent amendments to, or revisions of, any of these publications

do not apply. However, parties to agreements based on this part of ISO 12215 are encouraged to investigate the

possibility of applying the most recent editions of the normative documents indicated below. For undated

references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain

registers of currently valid International Standards.
ISO 8666: — , Small craft — Principal data

ISO 12215-4:2002, Small craft — Hull construction and scantlings — Part 4: Workshop and manufacturing

3 Terms and definitions

For the purposes of this part of ISO 12215, the following terms and definitions apply.

1) To be published.
© ISO 2002 – All rights reserved 1
---------------------- Page: 11 ----------------------
SIST EN ISO 12215-3:2018
ISO 12215-3:2002(E)
3.1
durability

naturally inherent property of a wood species to indicate the service time of the heartwood used in the open air

without any preservation
NOTE The designation of durability of wood is given in Table 1.
3.2
veneer
solid wood with a thickness of no more than 5 mm in its finished state
4 Requirements for metal
4.1 Properties of materials

Materials covered by this part of ISO 12215 are dealt with by many international and national standards, also

classification societies, active in the survey of ships and small craft. The properties of all metal used in the

construction of small craft shall be suitable for marine use and the intended methods of construction. The metal

shall comply with a relevant International or National Standard, classification society rule or be supported by

documentation to validate its suitability for marine use.
4.2 Selection of materials

The choice of materials shall take into account the manufacturing conditions in the boat yard, environmental

limitations, the anticipated manufacturing process, the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.