SIST EN ISO 717-2:1997/A1:2006
(Main)Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation - Amendment 1 (ISO 717-2:1996/AM 1:2006)
Acoustics - Rating of sound insulation in buildings and of building elements - Part 2: Impact sound insulation - Amendment 1 (ISO 717-2:1996/AM 1:2006)
This part of ISO 717 - defines single-number quantities for the impact sound insulation in buildings and of floors, and - gives rules for determining these quantities from the results of measurements carries out in one-third octave bands according to ISO 140-6 and ISO 140-7 - defines a single-number quantity for the impact soundreduction of floor coverings and floating floors from the results of measurements carried out acording to ISO 140-8.
Akustik - Bewertung der Schalldämmung in Gebäuden und von Bauteilen - Teil 2: Trittschalldämmung - Änderung 1: Rundungsregeln für Einzahlbewertungen und Einzahlangaben (ISO 717-2:1996/AM 1:2006)
Acoustique - Évaluation de l'isolement acoustique des immeubles et des éléments de construction - Partie 2: Protection contre le bruit de choc - Amendement 1 (ISO 717-2:1996/AM 1:2006)
Akustika - Vrednotenje zvočne izolirnosti v zgradbah in zvočne izolirnosti gradbenih elementov - 2. del: Izolirnost pred udarnim zvokom - Dopolnilo 1 (ISO 717-2:1996/AM 1:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 717-2:1997/A1:2006
01-december-2006
$NXVWLND9UHGQRWHQMH]YRþQHL]ROLUQRVWLY]JUDGEDKLQ]YRþQHL]ROLUQRVWL
JUDGEHQLKHOHPHQWRYGHO ,]ROLUQRVWSUHGXGDUQLP]YRNRP'RSROQLOR ,62
$0
Acoustics - Rating of sound insulation in buildings and of building elements - Part 2:
Impact sound insulation - Amendment 1 (ISO 717-2:1996/AM 1:2006)
Akustik - Bewertung der Schalldämmung in Gebäuden und von Bauteilen - Teil 2:
Trittschalldämmung - Änderung 1: Rundungsregeln für Einzahlbewertungen und
Einzahlangaben (ISO 717-2:1996/AM 1:2006)
Acoustique - Évaluation de l'isolement acoustique des immeubles et des éléments de
construction - Partie 2: Protection contre le bruit de choc - Amendement 1 (ISO 717-
2:1996/AM 1:2006)
Ta slovenski standard je istoveten z: EN ISO 717-2:1996/A1:2006
ICS:
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
SIST EN ISO 717-2:1997/A1:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 717-2:1996/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2006
ICS 91.120.20
English Version
Acoustics - Rating of sound insulation in buildings and of
building elements - Part 2: Impact sound insulation -
Amendment 1 (ISO 717-2:1996/AM 1:2006)
Acoustique - Évaluation de l'isolement acoustique des
immeubles et des éléments de construction - Partie 2:
Protection contre le bruit de choc - Amendement 1 (ISO
717-2:1996/AM 1:2006)
This amendment A1 modifies the European Standard EN ISO 717-2:1996; it was approved by CEN on 14 August 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 717-2:1996/A1:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 717-2:1996/A1:2006 (E)
Foreword
This document (EN ISO 717-2:1996/A1:2006) has been prepared by Technical Committee
CEN/TC 126 "Acoustic properties of building elements and of buildings", the secretariat of which
is held by AFNOR, in collaboration with Technical Committee ISO/TC 43 "Acoustics".
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2007, and conflicting national
standards shall be withdrawn at the latest by February 2007.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 717-2
Second edition
1996-12-15
AMENDMENT 1
2006-08-15
Acoustics — Rating of sound insulation
in buildings and of building elements —
Part 2:
Impact sound insulation
AMENDMENT 1
Acoustique — Évaluation de l'isolement acoustique des immeubles et
des éléments de construction —
Partie 2: Protection contre le bruit de choc
AMENDEMENT 1
Reference number
ISO 717-2:1996/Amd.1:2006(E)
©
ISO 2006
---------------------- Page: 4 ----------------------
ISO 717-2:1996/Amd.1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 717-2:1996/Amd.1:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 717-2:1996 was prepared by the European Committee for Standardization (CEN)
Technical Committee CEN/TC 126, Acoustic properties of building elements and of buildings in collaboration
with ISO Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building acoustics, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
© ISO 2006 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO 717-2:1996/Amd.1:2006(E)
Introduction
The existing texts on rounding of data in ISO 717-1 and ISO 717-2 are not very precise and lead to different
interpretations, especially when implemented numerically in computer software.
This amendment to ISO 717-2:1996 defines a procedure for evaluating the weighted reduction in impact
sound pressure level by floor coverings on lightweight floors, gives more precise instructions, and makes other
minor changes in the following parts of the document:
⎯ updating the normative references;
⎯ modification of the first paragraph of 4.3.1, Measurements in one-third-octave bands, and the addition of
a new footnote 1;
⎯ modification of the first paragraph of 4.3.2, Calculation of spectrum adaptation terms, and the addition of
a reference to the new footnote 1;
⎯ addition, after the existing Clause 5, of a new Clause 6 describing procedure for evaluating the weighted
reduction in impact sound pressure level by floor coverings on lightweight floors;
⎯ modification of Annex A;
⎯ modification of Annex B;
⎯ modification of Annex C;
⎯ deletion of the heading “Annex D,” leaving the title Bibliography" and the references.
iv © ISO 2006 – All rights reserved
---------------------- Page: 7 ----------------------
ISO 717-2:1996/Amd.1:2006(E)
Acoustics — Rating of sound insulation in buildings and of
building elements —
Part 2:
Impact sound insulation
AMENDMENT 1
Page 1, Scope:
Add the following text to the Scope as numbered item d) after the existing numbered item c):
d) defines a procedure fo
...
SLOVENSKI SIST EN ISO 717-
2:1997/OprA1:2004
PREDSTANDARD
september 2004
Acoustics - Rating of sound insulation in buildings and of building elements - Part 2:
Impact sound insulation - Amendment 1: Rounding rules related to single number
rating and single number quantities
ICS 91.120.20 Referenčna številka
SIST EN ISO 717-
2:1997/OprA1:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
FINAL DRAFT
EN ISO 717-2:1996
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2006
ICS 91.120.20
English Version
Acoustics - Rating of sound insulation in buildings and of
building elements - Part 2: Impact sound insulation -
Amendment 1 (ISO 717-2:1996/FDAM 1:2006)
Acoustique - Évaluation de l'isolement acoustique des
immeubles et des éléments de construction - Partie 2:
Protection contre le bruit de choc - Amendement 1 (ISO
717-2:1996/FDAM 1:2006)
This draft amendment is submitted to CEN members for parallel formal vote. It has been drawn up by the Technical Committee CEN/TC
126.
This draft amendment A1, if approved, will modify the European Standard EN ISO 717-2:1996. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 717-2:1996/prA1:2006: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 717-2:1996/prA1:2006 (E)
Foreword
This document (EN ISO 717-2:1996/prA1:2006) has been prepared by Technical Committee
CEN/TC 126 "Acoustic properties of building elements and of buildings", the secretariat of
which is held by AFNOR, in collaboration with Technical Committee ISO/TC 43 "Acoustics".
This document is currently submitted to the parallel Formal Vote.
2
---------------------- Page: 3 ----------------------
DRAFT AMENDMENT ISO 717-2:1996/DAmd 1
ISO/TC 43/SC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2004-06-03 2004-11-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Acoustics — Rating of sound insulation in buildings and of
building elements —
Part 2:
Impact sound insulation
AMENDMENT 1: Rounding rules related to single number ratings
and single number quantities
Acoustique — Évaluation de l'isolement acoustique des immeubles et des éléments de construction —
Partie 2: Protection contre le bruit de choc
AMENDEMENT 1: Règles d'arrondissement associées aux évaluations de numéro simple et aux quantités de
numéro simple
ICS 91.120.20
ISO/CEN PARALLEL ENQUIRY
This draft International Standard is a draft standard developed within the European Committee for
Standardization (CEN) and processed under the CEN-lead mode of collaboration as defined in the
Vienna Agreement. The document has been transmitted by CEN to ISO for circulation for ISO member
body voting in parallel with CEN enquiry. Comments received from ISO member bodies, including those
from non-CEN members, will be considered by the appropriate CEN technical body. Should this DIS be
accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-
month FDIS vote in ISO and formal vote in CEN.
In accordance with the provisions of Council Resolution 15/1993 this document is circulated in
the English language only.
Conformément aux dispositions de la Résolution du Conseil 15/1993, ce document est distribué
en version anglaise seulement.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2004
---------------------- Page: 4 ----------------------
ISO/DIS 717-2
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.