This document
a) defines single-number quantities for impact sound insulation in buildings and of floors,
b) gives rules for determining these quantities from the results of measurements carried out in
one-third-octave bands in accordance with ISO 10140-3 and ISO 16283-2, and in octave bands in
accordance with that option in ISO 16283-2 for field measurements only,
c) defines single-number quantities for the impact sound reduction of floor coverings and floating
floors calculated from the ...
view more

    • sale 10% off
    • Standard
      31 pages
      English language
    • e-Library read for
      1 day

This document specifies a test method for determining the non-combustibility performance, under
specified conditions, of homogeneous products and substantial components of non-homogeneous
products.
Information on the precision of the test method is given in Annex A.

    • sale 10% off
    • Standard
      39 pages
      English language
    • e-Library read for
      1 day

EN-ISO 11925-2 specifies a method of test for determining the ignitability ofproducts by direct small flame impingement under zero impressed irradiance usingvertically oriented test specimens. Information on the precision of the testmethod is given in Annex A (informative).Information on testing not essentiallyflat end-use products is given in Annex B (normative).Information on testingperforated end-use products is given in Annex C (normative).

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

This document specifies a method of test for determining the ignitability of products by direct small flame impingement under zero impressed irradiance using vertically oriented test specimens.
Information on the precision of the test method is given in Annex A (informative).
Information on testing not essentially flat end-use products is given in Annex B (normative).
Information on testing perforated end-use products is given in Annex C (normative).

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

This document specifies a method for the determination of the gross heat of combustion (QPCS) of
products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as
described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test m...
view more

    • sale 10% off
    • Standard
      37 pages
      English language
    • e-Library read for
      1 day

This document specifies a method for the determination of the gross heat of combustion (QPCS) of products at constant volume in a bomb calorimeter.
This method is intended to be applied to solid products.
NOTE Liquids can be tested with similar equipment and using conditions described in ASTM D240[1], as described in IEC 61039[2] using ISO 1928[3] test equipment.
Annex A specifies the calculation of the net heat of combustion, QPCI, when required.
Information on the precision of the test met...
view more

    • sale 10% off
    • Standard
      37 pages
      English language
    • e-Library read for
      1 day

This European Standard specifies the requirements, the basic performance criteria and the evaluation of conformity for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties steel, polymer or other fibres is also covered. It does not cover prefabricated reinforced components o...view more

    • sale 10% off
    • Standard
      76 pages
      English language
    • e-Library read for
      1 day

This document specifies the requirements, the basic performance criteria and the Assessment and Verification of Constancy of Performance (AVCP) for unreinforced, reinforced and prestressed precast concrete products made of compact light-, normal- and heavyweight concrete according to EN 206 with no appreciable amount of entrapped air other than entrained air. Concrete containing fibres for other than mechanical properties (steel, polymer or other fibres) is also covered. It does not cover prefab...view more

    • sale 10% off
    • Standard
      76 pages
      English language
    • e-Library read for
      1 day

This European Standard is for prefabricated reinforced components of autoclaved aerated concrete to be used in building construction for:
a) Structural elements:
- loadbearing wall components;
- retaining wall components;
- roof components;
- floor components;
- linear components (beams and piers).
b) Non-structural elements:
- nonloadbearing wall components (partition walls);
- cladding components (without fixtures) intended to be used for external facades of buildings;
- small box culverts use...
view more

    • sale 10% off
    • Standard
      180 pages
      English language
    • e-Library read for
      1 day

This European Standard is for prefabricated reinforced components of autoclaved aerated concrete to be used in building construction for:
a)   Structural elements:
-   loadbearing wall components;
-   retaining wall components;
-   roof components;
-   floor components;
-   linear components (beams and piers).
b)   Non-structural elements:
-   non-loadbearing wall components (partition walls);
-   cladding components (without fixtures) intended to be used for external facades of buildings;
-   small box c...
view more

    • sale 10% off
    • Standard
      180 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in expanded polystyrene (EPS), used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor systems. EPS block may be totally made in EPS or combined with different materials such as plaster or wood wool. If EPS is combined with other materials, these materials should not contribute to more than ...view more

    • sale 10% off
    • Standard
      55 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for lightweight blocks used as formwork during the construction of the floor system. The blocks are used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor systems. This European Standard does not deal with blocks made in polystyrene, with or without tong, or combined with different materials where polystyr...view more

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This European Standard identifies the requirements, the basic performance criteria and evaluation of conformity for precast linear elements (such as columns, beams and frame elements) made of reinforced or prestressed normal or lightweight concrete, used for the construction of the structures of buildings and other civil engineering works, except bridges. This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods, and aspects of transport and e...view more

    • sale 10% off
    • Standard
      33 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in expanded polystyrene (EPS), used in conjunction with precast concrete beams in compliance with
EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor systems.
EPS block may be totally made in EPS or combined with different materials such as plaster or wood wool.
If EPS is combined with other materials, these materials should not contribute to more t...
view more

    • sale 10% off
    • Standard
      55 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for lightweight blocks used as formwork during the construction of the floor system. The blocks are used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor systems.
This European Standard does not deal with blocks made in polystyrene, with or without tong, or combined with different materials where polysty...
view more

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This European Standard identifies the requirements, the basic performance criteria and evaluation of conformity for precast linear elements (such as columns, beams and frame elements) made of reinforced or prestressed normal or lightweight concrete, used for the construction of the structures of buildings and other civil engineering works, except bridges.
This document covers terminology, performance criteria, tolerances, relevant physical properties, test methods, and aspects of transport and...
view more

    • sale 10% off
    • Standard
      33 pages
      English language
    • e-Library read for
      1 day

This European Standard applies to prefabricated walls, made of normal weight or lightweight concrete with dense structure. Also fibre reinforced concrete (steel, polymer or other fibres covered by European standards) may be used. These wall elements may have external wall functions (see 3.11) or not, have facing functions (see 3.12) or not or have a combination of these functions.
External wall functions could be:
-   thermal insulation (see 3.11.1);
-   sound insulation (see 3.11.2);
-   hygromet...
view more

    • sale 10% off
    • Standard
      38 pages
      English language
    • e-Library read for
      1 day

This European Standard applies to prefabricated walls, made of normal weight or lightweight concrete with dense structure. Also fibre reinforced concrete (steel, polymer or other fibres covered by European standards) may be used. These wall elements may have external wall functions (see 3.11) or not, have facing functions (see 3.12) or not or have a combination of these functions.
External wall functions could be:
-   thermal insulation (see 3.11.1);
-   sound insulation (see 3.11.2);
-   hygromet...
view more

    • sale 10% off
    • Standard
      38 pages
      English language
    • e-Library read for
      1 day

This European Standard applies to precast concrete structural elements produced in a factory and used in bridge construction, such as deck elements.Normal weight concrete elements are considered, both reinforced and prestressed; their use can be on road bridges, railway bridges and footbridges.
Deck elements include both single elements from which the deck may be composed (beams, slabs, ribbed or cellular elements) and elements consisting of a segment of the entire deck.
Some examples of eleme...
view more

    • sale 10% off
    • Standard
      60 pages
      English language
    • e-Library read for
      1 day

This European standard specifies precast products in reinforced or prestressed concrete with or without fibres, to be used together or in combination with other elements to erect fences e.g. boundary fences.
This European standard covers both mechanical resistance determined by calculation and load bearing capacity determined by testing.
Normal weight concrete or light weight concrete elements include posts, solid or open panels, slabs, rails, spurs, struts and base panels.
The intended uses...
view more

    • sale 10% off
    • Standard
      52 pages
      English language
    • e-Library read for
      1 day

This European Standard applies to precast concrete structural elements produced in a factory and used in bridge construction, such as deck elements.Normal weight concrete elements are considered, both reinforced and prestressed; their use can be on road bridges, railway bridges and footbridges.
Deck elements include both single elements from which the deck may be composed (beams, slabs, ribbed or cellular elements) and elements consisting of a segment of the entire deck.
Some examples of eleme...
view more

    • sale 10% off
    • Standard
      60 pages
      English language
    • e-Library read for
      1 day

This European standard specifies precast products in reinforced or pre-stressed concrete with or without fibres, to be used together or in combination with other elements to erect fences e.g. boundary fences.
This European standard covers both mechanical resistance determined by calculation and load bearing capacity determined by testing.
Normal weight concrete or light weight concrete elements include posts, solid or open panels, slabs, rails, spurs, struts and base panels.
The intended use...
view more

    • sale 10% off
    • Standard
      52 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with both large (structural) and small (non-structural or light structural) box culverts of rectangular cross-section formed monolithically and designed as continuous elements with a joint detail shaped to allow the possible incorporation of sealing materials. Box culverts can be used for creation of voids below ground for conveyance and storage of materials. e.g. conveyance and storage of wastewater, cable tunnels and subways
For the purposes of this European Stand...
view more

    • sale 10% off
    • Standard
      40 pages
      English language
    • e-Library read for
      1 day

This document identifies the requirements, the basic performance criteria and evaluation of conformity for precast ribbed elements made of reinforced or prestressed normal weight concrete, used in floors or roofs. The elements consist of a top and/or bottom slab and one or more (usually two) ribs; transverse ribs may also be present.
Some examples of precast elements considered in this document are shown in Annex A.
Specific requirements for minor floor elements are listed in the Annex B.
Thi...
view more

    • sale 10% off
    • Standard
      43 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria and specifies minimum values where appropriate for precast hollow core slabs made of prestressed or reinforced normal weight concrete according to EN 1992-1-1:2004. This European Standard covers terminology, performance criteria, tolerances, relevant physical properties, special test methods, and special aspects of transport and erection. Hollow core elements are used in floors, roofs, walls and similar applica...view more

    • sale 10% off
    • Standard
      81 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with both large (structural) and small (non-structural or light structural) box culverts of rectangular cross-section formed monolithically and designed as continuous elements with a joint detail shaped to allow the possible incorporation of sealing materials. Box culverts can be used for creation of voids below ground for conveyance and storage of materials. e.g. conveyance and storage of wastewater, cable tunnels and subways
For the purposes of this European Stand...
view more

    • sale 10% off
    • Standard
      40 pages
      English language
    • e-Library read for
      1 day

This document identifies the requirements, the basic performance criteria and evaluation of conformity for precast ribbed elements made of reinforced or prestressed normal weight concrete, used in floors or roofs. The elements consist of a top and/or bottom slab and one or more (usually two) ribs; transverse ribs may also be present.
Some examples of precast elements considered in this document are shown in Annex A.
Specific requirements for minor floor elements are listed in Annex B.
This do...
view more

    • sale 10% off
    • Standard
      43 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria and specifies minimum values where appropriate for precast hollow core slabs made of prestressed or reinforced normal weight concrete according to EN 1992-1-1:2004.
This European Standard covers terminology, performance criteria, tolerances, relevant physical properties, special test methods, and special aspects of transport and erection.
Hollow core elements are used in floors, roofs, walls and similar appli...
view more

    • sale 10% off
    • Standard
      81 pages
      English language
    • e-Library read for
      1 day

This European Standard is for prefabricated reinforced components of lightweight aggregate concrete (LAC) with open structure intended to be used in building constructions.

    • sale 10% off
    • Standard
      109 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in normal or lightweight aggregate concrete, used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor and roof systems.
Examples of typology of floor and roof systems are given in Annex B of EN 15037-1:2008.

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in clay, used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-insitu concrete for the construction of beam-and-block floor and roof systems.
Examples of typology of floor and roof systems are given in Annex B of EN 15037-1:2008.

    • sale 10% off
    • Standard
      40 pages
      English language
    • e-Library read for
      1 day

This European Standard is for prefabricated components of lightweight aggregate concrete (LAC) with open structure and with structural or non-structural reinforcement intended to be used in building construction
a)   for structural elements:
-   loadbearing wall components (solid, hollow core or multilayer);
-   retaining wall components (solid) with or without surcharge loading;
-   roof components (solid, hollow core or multilayer);
-   floor components (solid, hollow core or multilayer);
-   linear...
view more

    • sale 10% off
    • Standard
      109 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in clay, used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor and roof systems.
Examples of typology of floor and roof systems are given in Annex B of EN 15037-1:2008.

    • sale 10% off
    • Standard
      40 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements and the basic performance criteria for blocks made in normal or lightweight aggregate concrete, used in conjunction with precast concrete beams in compliance with EN 15037-1, with or without cast-in-situ concrete for the construction of beam-and-block floor and roof systems.
Examples of typology of floor and roof systems are given in Annex B of EN 15037-1:2008.

    • sale 10% off
    • Standard
      36 pages
      English language
    • e-Library read for
      1 day

This part of ISO 10140 specifies the basic measurement procedures for airborne and impact sound insulation in laboratory test facilities.

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day

This part of ISO 10140 specifies laboratory methods for measuring the impact sound insulation of floor assemblies. The test results can be used to compare the sound insulation properties of building elements, classify elements according to their sound insulation capabilities, help design building products which require certain acoustic properties and estimate the in situ performance in complete buildings. The measurements are performed in laboratory test facilities in which sound transmission vi...view more

    • sale 10% off
    • Standard
      21 pages
      English language
    • e-Library read for
      1 day

This European standard deals with the requirements, the basic performance criteria and evaluation of conformity for precast floor plates made of reinforced or prestressed normal weight concrete according to EN 1992-1-1:2004, used in conjunction with cast-in-situ concrete (topping) for the construction of composite floor slabs. Annex B gives different types of composite slabs made with floor plates.
These floor plates, with or without void formers, can include lattice girders or stiffening ribs ...
view more

    • sale 10% off
    • Standard
      87 pages
      English language
    • e-Library read for
      1 day

This European standard deals with the requirements, the basic performance criteria and evaluation of conformity for precast floor plates made of reinforced or prestressed normal weight concrete according to EN 1992-1-1:2004, used in conjunction with cast-in-situ concrete (topping) for the construction of composite floor slabs. Annex B gives different types of composite slabs made with floor plates.
These floor plates, with or without void formers, can include lattice girders or stiffening ribs ...
view more

    • sale 10% off
    • Standard
      87 pages
      English language
    • e-Library read for
      1 day

This document identifies the requirements, the basic performance criteria and the evaluation of conformity for special precast roof elements made of reinforced or prestressed normal weight concrete, used for the construction of buildings, with or without separating function with respect to fire resistance.
NOTE   The title of special roof elements refers to thin-walled structural elements with deformable transverse profile, such as folded plates, or shell elements, the intended use being specific...
view more

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This document identifies the requirements, the basic performance criteria and the evaluation of conformity for special precast roof elements made of reinforced or prestressed normal weight concrete, used for the construction of buildings, with or without separating function with respect to fire resistance.
NOTE   The title of special roof elements refers to thin-walled structural elements with deformable transverse profile, such as folded plates, or shell elements, the intended use being specific...
view more

    • sale 10% off
    • Standard
      58 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements, the basic performance criteria and evaluation of conformity for precast elements made of plain, reinforced or prestressed normal weight concrete, used for the construction of retaining walls. The products covered by this European Standard are intended to be used as part of retaining walls in applications such as: to retain natural ground excavations and trenches; to retain earth fills for roads, platforms, etc.; in bridge abutments and their fl...view more

    • sale 10% off
    • Standard
      31 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      32 pages
      German language
    • e-Library read for
      1 day

This European Standard deals with the requirements, the basic performance criteria and evaluation of conformity for precast elements made of plain, reinforced or prestressed normal weight concrete, used for the construction of retaining walls.
The products covered by this European Standard are intended to be used as part of retaining walls in applications such as:
- to retain natural ground excavations and trenches;
- to retain earth fills for roads, platforms, etc.;
- in bridge abutments an...
view more

    • sale 10% off
    • Standard
      31 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      32 pages
      German language
    • e-Library read for
      1 day

This European Standard specifies the properties, performance and test methods of factory made, non-load-bearing hollow wood-chip concrete shuttering blocks, which may include factory installed thermal insulation. These blocks are intended to be used for external and internal walls and partitions when filled with concrete.

    • sale 10% off
    • Standard
      53 pages
      English language
    • e-Library read for
      1 day

Specification of non loadbearing shuttering blocks, made of concrete with normal weight or lightweight aggregates, with or without integrated thermal insulation. Shuttering blocks are intended to  be used to form walls and partitions when  filled with concrete or mortar. Concrete  shuttering blocks rely on a concrete or  mortar infill for their structural performance  and are not intended to be used unfilled. This  standard does not cover masonry units  covered in EN 771-3.

    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day

This European Standard specifies the properties, performance and test methods of factory made, non-load bearing hollow concrete shuttering blocks made from normal weight or lightweight aggregates or a combination of both. Shuttering blocks may include vertical or horizontal interlocking features and factory installed supplementary insulation. Shuttering blocks are intended to be used to form walls and partitions when filled with concrete or mortar. Concrete shuttering blocks rely on a concrete o...view more

    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day

This European Standard deals with the requirements, the basic performance criteria and evaluation of conformity for precast beams made of reinforced or prestressed normal weight concrete according to EN 1992-1-1:2004, with or without clay shell, used in conjunction with blocks in compliance with EN 15037-2 or EN 15037-3 or prEN 15037-4 or prEN 15037-5, with or without cast in-situ concrete for the construction of beam-and-block floor and roof systems. Examples of typology of floor and roof syste...view more

    • sale 10% off
    • Standard
      93 pages
      English language
    • e-Library read for
      1 day

This European Standard specifies the properties, performance and test methods of factory made, non-load-bearing hollow wood-chip concrete shuttering blocks, which may include factory installed thermal insulation.
These blocks are intended to be used for external and internal walls and partitions when filled with concrete.

    • sale 10% off
    • Standard
      53 pages
      English language
    • e-Library read for
      1 day

This document specifies the terminology, requirements, basic performance criteria, test methods and evaluation of conformity that will be applied to precast concrete foundation piles, factory produced for building and civil engineering works and installed at the site by the use of impact, vibration, pressing or other suitable techniques. This document may also be applied to products manufactured in temporary plants on site where production is controlled in accordance with the provisions of Claus...view more

    • sale 10% off
    • Standard
      44 pages
      English language
    • e-Library read for
      1 day