SIST EN ISO 12058-1:2018

Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:2018)

This document specifies the general principles of a method, using an inclined‑tube falling‑ball
viscometer, for determining the viscosity of polymers and resins in the liquid emulsified or dispersed
state. It is intended for application to liquids over a viscosity measurement range of 0,6 mPa·s to
250 000 mPa·s (temperature range −20 °C to +120 °C) for which the shear stress and shear rate are
proportional, i.e. the viscosity is independent of the shear rate. This ideal behaviour is commonly
known as Newtonian behaviour. If a liquid differs significantly from this behaviour, different results
can be obtained with the different balls of a falling‑ball viscometer or from viscometers with different
geometries, such as capillary and rotational viscometers.

Kunststoffe - Bestimmung der Viskosität mit einem Kugelfall-Viskosimeter - Teil 1: Verfahren nach Höppler (ISO 12058-1:2018)

Plastiques - Détermination de la viscosité au moyen d'un viscosimètre à chute de bille - Partie 1: Méthode du tube incliné (ISO 12058-1:2018)

Le présent document spécifie les principes généraux d'une méthode utilisant un viscosimètre à chute de bille dans un tube incliné pour la détermination de la viscosité des polymères et des résines à l'état liquide en émulsion ou en dispersion. Il est applicable, dans une plage de mesurage de la viscosité de 0,6 mPa·s à 250 000 mPa·s (plage de température de −20 °C à +120 °C), aux liquides dont la contrainte de cisaillement et la vitesse de cisaillement sont proportionnelles, ce qui signifie que la viscosité de ces liquides est indépendante de la vitesse de cisaillement. Ce comportement idéal est couramment dénommé «visco-élasticité newtonienne». Lorsque les caractéristiques d'un liquide donné ne correspondent pas à ce comportement, il arrive que l'on obtienne des résultats différents quand on utilise des billes différentes ou des viscosimètres de géométries différentes, tels que les viscosimètres capillaires et rotatifs.

Polimerni materiali - Določanje viskoznosti z uporabo viskozimetra s padajočo kroglico - 1. del: Metoda z nagnjeno cevjo (ISO 12058-1:2018)

Ta dokument določa splošna načela metode z uporabo viskozimetra s padajočo kroglico po nagnjeni cevi za določanje viskoznosti polimerov in smol v tekočem emulgiranem ali dispergiranem stanju. Uporablja se za tekočine v merilnem območju viskoznosti od 0,6 mPa s do 250.000 mPa s (temperaturno območje od –20 °C do 120 °C) s sorazmerno strižno napetostjo in strižno hitrostjo, tj. viskoznost je neodvisna od strižne hitrosti. Te idealne lastnosti so splošno znane kot Newtonove lastnosti. Če so lastnosti tekočine bistveno drugačne od teh, lahko pride do različnih rezultatov z različnimi kroglicami viskozimetra s padajočo kroglico ali z viskozimetri različnih geometrij, kot so kapilarni in rotacijski viskozimetri.

General Information

• Status: Published
• Public Enquiry End Date: 31-May-2018
• Publication Date: 23-Sep-2018
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 31-Aug-2018
• Due Date: 05-Nov-2018
• Completion Date: 24-Sep-2018
• Ref Project: EN ISO 12058-1:2018 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:2018)

Relations

• Revised: SIST EN ISO 12058-1:2003 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
• Effective Date: 06-Dec-2017
• Revised: SIST EN ISO 12058-1:2003/AC:2005 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
• Effective Date: 06-Dec-2017
• Replaces: SIST EN ISO 12058-1:2003 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
• Effective Date: 29-Aug-2018
• Replaces: SIST EN ISO 12058-1:2003/AC:2005 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
• Effective Date: 29-Aug-2018
• Replaces: SIST EN ISO 12058-1:2003 - Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube method (ISO 12058-1:1997)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12058-1:2018
01-november-2018
1DGRPHãþD
SIST EN ISO 12058-1:2003
SIST EN ISO 12058-1:2003/AC:2005
3ROLPHUQLPDWHULDOL'RORþDQMHYLVNR]QRVWL]XSRUDERYLVNR]LPHWUDVSDGDMRþR
NURJOLFRGHO0HWRGD]QDJQMHQRFHYMR,62
Plastics - Determination of viscosity using a falling-ball viscometer - Part 1: Inclined-tube
method (ISO 12058-1:2018)
Kunststoffe - Bestimmung der Viskosität mit einem Kugelfall-Viskosimeter - Teil 1:
Verfahren nach Höppler (ISO 12058-1:2018)
Plastiques - Détermination de la viscosité au moyen d'un viscosimètre à chute de bille -
Partie 1: Méthode du tube incliné (ISO 12058-1:2018)
Ta slovenski standard je istoveten z: EN ISO 12058-1:2018
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 12058-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12058-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 12058-1:2018


EN ISO 12058-1
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2018
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 12058-1:2002
English Version

Plastics - Determination of viscosity using a falling-ball
viscometer - Part 1: Inclined-tube method (ISO 12058-
1:2018)
Plastiques - Détermination de la viscosité au moyen Kunststoffe - Bestimmung der Viskosität mit einem
d'un viscosimètre à chute de bille - Partie 1: Méthode Kugelfall-Viskosimeter - Teil 1: Verfahren nach
du tube incliné (ISO 12058-1:2018) Höppler (ISO 12058-1:2018)
This European Standard was approved by CEN on 10 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12058-1:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12058-1:2018
EN ISO 12058-1:2018 (E)
Contents Page
European foreword . 3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 12058-1:2018
EN ISO 12058-1:2018 (E)
European foreword
This document (EN ISO 12058-1:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards
shall be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12058-1:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 12058-1:2018 has been approved by CEN as EN ISO 12058-1:2018 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 12058-1:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 12058-1:2018
INTERNATIONAL ISO
STANDARD 12058-1
Second edition
2018-07
Plastics — Determination of viscosity
using a falling-ball viscometer —
Part 1:
Inclined-tube method
Plastiques — Détermination de la viscosité au moyen d'un
viscosimètre à chute de bille —
Partie 1: Méthode du tube incliné
Reference number
ISO 12058-1:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 12058-1:2018
ISO 12058-1:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 12058-1:2018
ISO 12058-1:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative reference . 1
3 Terms and definitions . 1
4 Principle . 1
5 Measurand and units. 1
6 Measurement range and temperature range . 2
7 Apparatus . 2
7.1 Falling-ball viscometer . 2
7.2 Thermometer . 4
7.3 Timer . 4
7.4 Thermostat . 4
8 Sampling . 4
9 Procedure. 4
10 Expression of results . 5
11 Precision . 5
12 Test report . 6
Bibliography . 7
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 12058-1:2018
ISO 12058-1:2018(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of sta
...