SIST EN ISO 15106-3:2005

Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method (ISO 15106-3:2003)

ISO 15106-3:2003 specifies an instrumental method for determining the water vapour transmission rate of plastic film, plastic sheeting and multi-layer structures including plastics, using an electrolytic detection sensor.
NOTE The method provides rapid measurement over a wide range of water vapour transmission rates.

Kunststoffe - Folien und Flächengebilde - Bestimmung der Wasserdampfdurchlässigkeit - Teil 3: Elektrolytnachweis-Sensorverfahren (ISO 15106-3:2003)

Dieser Teil von ISO 15106 legt ein instrumentelles Verfahren zum Bestimmen der Wasserdampfdurchlässigkeit von Kunststofffolien, Kunststoffbahnen ( platten) und Mehrschichtgebilden mit Kunststoffanteil unter Anwendung eines Elektrolysesensors fest.
ANMERKUNG   Das Verfahren ermöglicht die schnelle Messung über einen breiten Wertebereich der Wasserdampfdurchlässigkeit.

Plastiques - Film et feuille - Détermination du coefficient de transmission de vapeur d'eau - Partie 3: Méthode utilisant un détecteur électrolytique (ISO 15106-3:2003)

L'ISO 15106-3:2003 spécifie une méthode instrumentée de détermination du coefficient de transmission de vapeur d'eau d'un film plastique, d'une feuille ou d'un complexe comprenant des plastiques, avec un détecteur électrolytique.
Cette méthode fournit un mesurage rapide dans une large gamme de coefficients de transmission de vapeur d'eau.

Polimerni materiali - Filmi in plošče - Ugotavljanje prepustnosti vodnih hlapov - 3. del: Odkrivanje z elektrolitskim senzorjem (ISO 15106-3:2003)

General Information

• Status: Published
• Publication Date: 30-Apr-2005
• ICS: 83.140.10 - Films and sheets
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-May-2005
• Due Date: 01-May-2005
• Completion Date: 01-May-2005
• Ref Project: EN ISO 15106-3:2005 - Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method (ISO 15106-3:2003)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Folien und Flächengebilde - Bestimmung der Wasserdampfdurchlässigkeit - Teil 3: Elektrolytnachweis-Sensorverfahren (ISO 15106-3:2003)Plastiques - Film et feuille - Détermination du coefficient de transmission de vapeur d'eau - Partie 3: Méthode utilisant un détecteur électrolytique (ISO 15106-3:2003)Plastics - Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method (ISO 15106-3:2003)83.140.10Filmi in folijeFilms and sheetsICS:Ta slovenski standard je istoveten z:EN ISO 15106-3:2005SIST EN ISO 15106-3:2005en,fr,de01-maj-2005SIST EN ISO 15106-3:2005SLOVENSKI
STANDARD



SIST EN ISO 15106-3:2005



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 15106-3February 2005ICS 83.140.10English versionPlastics - Film and sheeting - Determination of water vapourtransmission rate - Part 3: Electrolytic detection sensor method(ISO 15106-3:2003)Plastiques - Film et feuille - Détermination du coefficient detransmission de vapeur d'eau - Partie 3: Méthode utilisantun détecteur électrolytique (ISO 15106-3:2003)Kunststoffe - Folien und Flächengebilde - Bestimmung derWasserdampfdurchlässigkeit - Teil 3: Elektrolytnachweis-Sensorverfahren (ISO 15106-3:2003)This European Standard was approved by CEN on 3 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 15106-3:2005: ESIST EN ISO 15106-3:2005



EN ISO 15106-3:2005 (E)
2
Foreword
The text of ISO 15106-3:2003 has been prepared by Technical Committee ISO/TC 61 "Plastics” of the International Organization for Standardization (ISO) and has been taken over as EN ISO 15106-3:2005 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn at the latest by August 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 15106-3:2003 has been approved by CEN as EN ISO 15106-3:2005 without any modifications.
SIST EN ISO 15106-3:2005



Reference numberISO 15106-3:2003(E)© ISO 2003
INTERNATIONAL STANDARD ISO15106-3First edition2003-01-15Plastics — Film and sheeting — Determination of water vapour transmission rate — Part 3: Electrolytic detection sensor method Plastiques — Film et feuille — Détermination du coefficient de transmission de vapeur d'eau — Partie 3: Méthode utilisant un détecteur électrolytique
SIST EN ISO 15106-3:2005



ISO 15106-3:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii © ISO 2003 — All rights reserved
SIST EN ISO 15106-3:2005



ISO 15106-3:2003(E) © ISO 2003 — All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Term and definition.1 4 Principle.1 5 Test specimens.2 6 Conditioning.2 7 Apparatus.2 8 Test conditions.3 9 Procedure.4 10 Calculation.4 11 Test result.4 12 Precision.5 13 Test report.5 Annex A (informative)
Relationship between relative humidity and concentration of sulfuric acid solution.6
SIST EN ISO 15106-3:2005



ISO 15106-3:2003(E) iv © ISO 2003 — All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15106-3 was prepared by Technical
...