SIST EN ISO 15013:2022
(Main)Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)
Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO 15013:2022)
This document specifies the requirements and test methods for solid flat extruded sheets of
polypropylene homopolymers (PP‑H) and polypropylene copolymers (PP‑B and PP‑R) without fillers or
reinforcing materials. This document applies to PP sheet in rolled form. It applies only to thicknesses of
0,5 mm to 40 mm.
Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP) - Anforderungen und Prüfung (ISO 15013:2022)
Diese Internationale Norm legt die Anforderungen und Prüfverfahren für massive, ebene, extrudierte Tafeln aus Polypropylen-Homopolymerisaten (PP-H) und Polypropylen-Copolymerisaten (PP-B und PP-R) ohne Füll- und Verstärkungsstoffe fest. Sie gilt darüber hinaus für gerollte PP-Tafeln. Diese Internationale Norm gilt nur für Tafeldicken von 0,5 mm bis 40 mm.
Plastiques - Plaques extrudées en polypropylène (PP) - Exigences et méthodes d'essai (ISO 15013:2022)
Le présent document spécifie les exigences et les méthodes d’essai relatives aux plaques compactes et planes, extrudées en polypropylène homopolymère (PP-H) et polypropylène copolymère (PP-B et PP-R) sans adjonction de charges ni de renforts. Le présent document s’applique aux plaques en PP enroulées en rouleaux. Elle s’applique uniquement aux plaques d’épaisseur comprise entre 0,5 mm et 40 mm.
Polimerni materiali - Ekstrudirane plošče iz polipropilena (PP) - Zahteve in preskusne metode (ISO 15013:2022)
Ta dokument določa zahteve in preskusne metode za masivne ravne ekstrudirane plošče iz polipropilen homopolimerov (PP H) oziroma polipropilen kopolimerov (PP B in PP R) brez polnil ali materialov za ojačanje. Ta dokument se uporablja za valjane plošče iz polipropilena. Uporablja se le za debeline od 0,5 mm do 40 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 15013:2022
01-maj-2022
Nadomešča:
SIST EN ISO 15013:2008
Polimerni materiali - Ekstrudirane plošče iz polipropilena (PP) - Zahteve in
preskusne metode (ISO 15013:2022)
Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods (ISO
15013:2022)
Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP) - Anforderungen und Prüfung
(ISO 15013:2022)
Plastiques - Plaques extrudées en polypropylène (PP) - Exigences et méthodes d'essai
(ISO 15013:2022)
Ta slovenski standard je istoveten z: EN ISO 15013:2022
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 15013:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15013:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 15013:2022
EN ISO 15013
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2022
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 15013:2007
English Version
Plastics - Extruded sheets of polypropylene (PP) -
Requirements and test methods (ISO 15013:2022)
Plastiques - Plaques extrudées en polypropylène (PP) - Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP)
Exigences et méthodes d'essai (ISO 15013:2022) - Anforderungen und Prüfung (ISO 15013:2022)
This European Standard was approved by CEN on 24 January 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15013:2022 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15013:2022
EN ISO 15013:2022 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15013:2022
EN ISO 15013:2022 (E)
European foreword
This document (EN ISO 15013:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2022, and conflicting national standards
shall be withdrawn at the latest by September 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15013:2007.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15013:2022 has been approved by CEN as EN ISO 15013:2022 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15013:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 15013:2022
INTERNATIONAL ISO
STANDARD 15013
Third edition
2022-02
Plastics — Extruded sheets of
polypropylene (PP) — Requirements
and test methods
Plastiques — Plaques extrudées en polypropylène (PP) — Exigences
et méthodes d'essai
Reference number
ISO 15013:2022(E)
© ISO 2022
---------------------- Page: 7 ----------------------
SIST EN ISO 15013:2022
ISO 15013:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 15013:2022
ISO 15013:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Material. 1
5 Requirements . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 2
5.2.1 Thickness . 2
5.2.2 Length and width . . 2
5.2.3 Rectangularity . 3
5.2.4 Bow of sheets in rolled form . 3
5.3 Properties . 3
5.3.1 Mechanical and thermal properties . 3
5.3.2 Behaviour on heating . 4
5.3.3 Physiological behaviour . 4
6 Test methods . 4
6.1 Test specimens. 4
6.1.1 Preparation of test specimens . 4
6.1.2 Conditioning . 4
6.1.3 Testing . 4
6.2 Delivery condition . 4
6.3 Appearance . 5
6.4 Dimensions . 5
6.4.1 Thickness, h . 5
6.4.2 Length, l, and width, b . . . 5
6.4.3 Rectangularity . 5
6.4.4 Bow of sheets in rolled form . 5
6.5 Tensile stress at yield, σ , and tensile strain at yield, ε . 5
y y
6.6 Modulus of elasticity in tension, E . 5
t
6.7 Charpy impact strength of notched specimens, a . 5
cn
6.8 Melt mass-flow rate (MFR) . 6
6.9 Heat resistance . 6
6.10 Determination of shrinkage on heating . 6
7 Designation and order specification . 7
7.1 Example for sheets . 7
7.2 Example for sheets in rolled form . 8
8 Marking . . 8
Annex A (normative) Requirements for rectangularity . 9
iii
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 15013:2022
ISO 15013:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products,
in collaboration with the European Committee for Standardization (CEN) Technical Committee CEN/
TC 249, Plastics, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This third edition cancels and replaces the second edition (ISO 15013:2007), which has been technically
revised. The main changes compared to the previous edition are as follows.
— The minimum value of tensile strain at yield for PP-H group 1.1 in Table 2 has been changed from
≥ 9 % to ≥ 7 %.
— The mandatory Clause 3 (Terms and definitions clause) has been added and subsequent clauses
have been renumbered.
Any feedback or questions on this document should be directed to the user’s national standards body. A
...
SLOVENSKI STANDARD
oSIST prEN ISO 15013:2021
01-junij-2021
Polimerni materiali - Ekstrudirane plošče iz polipropilena (PP) - Zahteve in
preskusne metode (ISO/DIS 15013:2021)
Plastics - Extruded sheets of polypropylene (PP) - Requirements and test methods
(ISO/DIS 15013:2021)
Kunststoffe - Extrudierte Tafeln aus Polypropylen (PP) - Anforderungen und Prüfung
(ISO/DIS 15013:2021)
Plastiques - Plaques extrudées en polypropylène (PP) - Exigences et méthodes d'essai
(ISO/DIS 15013:2021)
Ta slovenski standard je istoveten z: prEN ISO 15013
ICS:
83.140.10 Filmi in folije Films and sheets
oSIST prEN ISO 15013:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 15013:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 15013:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15013
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2021-03-29 2021-06-21
Plastics — Extruded sheets of polypropylene (PP) —
Requirements and test methods
Plastiques — Plaques extrudées en polypropylène (PP) — Exigences et méthodes d'essai
ICS: 83.140.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15013:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 15013:2021
ISO/DIS 15013:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 15013:2021
ISO/DIS 15013:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Material . 1
4 Requirements . 1
4.1 Appearance . 1
4.2 Dimensional tolerances . 2
4.2.1 Thickness . 2
4.2.2 Length and width . 2
4.2.3 Rectangularity . 2
4.2.4 Bow of sheets in rolled form . 3
4.3 Properties . 3
4.3.1 Mechanical and thermal properties . 3
4.3.2 Behaviour on heating . 3
4.3.3 Physiological behaviour . . 4
5 Test methods . 4
5.1 Test specimens . 4
5.1.1 Preparation of test specimens . 4
5.1.2 Conditioning . 4
5.1.3 Testing . 4
5.2 Delivery condition . 4
5.3 Appearance . 4
5.4 Dimensions . 5
5.4.1 Thickness, h .5
5.4.2 Length, l, and width, b .5
5.4.3 Rectangularity . 5
5.4.4 Bow of sheets in rolled form . 5
5.5 Tensile stress at yield, σ , and tensile strain at yield, ε .
y y 5
5.6 Modulus of elasticity in tension, E .
t 5
5.7 Charpy impact strength of notched specimens, a .
cn 5
5.8 Melt mass-flow rate (MFR) . 5
5.9 Heat resistance . 6
5.10 Determination of shrinkage on heating . 6
6 Designation . 7
6.1 Example for sheets. 7
6.2 Example for sheets in rolled form . 7
7 Marking . 8
Annex A (normative) Requirements for rectangularity . 9
© ISO 2021 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 15013:2021
ISO/DIS 15013:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15013 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
This third edition cancels and replaces the second edition (ISO 15013:2007), which has been technically
revised. The changes compared to the previous edition are as follows:
― The minimum value of tensile strain at yield for PP-H group 1.1 in Table 2 has been changed from
≥ 9 % to ≥ 7 %.
iv © ISO 2021 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 15013:2021
DRAFT INTERNATIONAL STANDARD ISO/DIS 15013:2021(E)
Plastics — Extruded sheets of polypropylene (PP) —
Requirements and test methods
1 Scope
This International Standard specifies the requirements and test methods for solid flat extruded sheets
of polypropylene homopolymers (PP-H) and polypropylene copolymers (PP-B and PP-R) without fillers
or reinforcing materials. This International Standard also applies to PP sheet in rolled form. It applies
only to thicknesses of 0,5 mm to 40 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 1133, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR)
of thermoplastics
ISO 1873-1, Plastics — Polypropylene (PP) moulding and extrusion materials — Part 1: Designation system
and basis for specifications
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 4577, Plastics — Polypropylene and propylene-copolymers — Determination of thermal oxidative
stability in air — Oven method
ISO 11501, Plastics — Film and sheeting — Determination of dimensional change on heating
3 Material
Sheets shall consist of PP extrusion compounds as defined in ISO 1873-1, without fill
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.