iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 15002:2008/A1:2020

(Amendment)

Flow-metering devices for connection to terminal units of medical gas pipeline systems - Amendment 1 (ISO 15002:2008/Amd 1:2018)

Flow-metering devices for connection to terminal units of medical gas pipeline systems - Amendment 1 (ISO 15002:2008/Amd 1:2018)

This International Standard specifies requirements and test methods for amalgam separators used in connection with dental equipment in the dental treatment centre. It specifies the efficiency of the amalgam separators in terms of the level of retention of amalgam based on a laboratory test and the test procedure for determining this efficiency. It also includes requirements for the safe functioning of the amalgam separator, for marking, and for instructions for use, operation and maintenance. All tests described in this International Standard are type tests.

Durchflussmesseinrichtungen zum Anschluss an Entnahmestellen von Rohrleitungssystemen für medizinische Gase - Änderung 1 (ISO 15002:2008/Amd 1:2018)

Dispositifs de mesure de débit pour raccordement aux prises murales des systèmes de distribution de gaz médicaux - Amendement 1 (ISO 15002:2008/Amd 1:2018)

Pretočni merilniki za priključitev na končne dele napeljav za medicinske pline - Dopolnilo A1 (ISO 15002:2008/Amd 1:2018)

General Information

Status
Withdrawn
Public Enquiry End Date
09-May-2017
Publication Date
09-Jan-2020
Withdrawal Date
10-Apr-2024
ICS
11.040.10 - Anaesthetic, respiratory and reanimation equipment
Technical Committee
VAZ - Healthcare
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
09-Apr-2024
Due Date
02-May-2024
Completion Date
11-Apr-2024
Directive
93/42/EEC - Council Directive 93/42/EEC of 14 June 1993 concerning medical devices
Mandate
M/023 - Standardization mandate to CEN/CENELEC concerning the development of European standards relating to medical devices
Ref Project
EN ISO 15002:2008/A1:2019 - Flow-metering devices for connection to terminal units of medical gas pipeline systems - Amendment 1 (ISO 15002:2008/Amd 1:2018)

Relations

Replaced By
SIST EN ISO 15002:2024 - Flow control devices for connection to a medical gas supply system (ISO 15002:2023)
Effective Date
08-Apr-2024
Amends
SIST EN ISO 15002:2008 - Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO 15002:2008)
Effective Date
01-Feb-2020

Buy Standard

EN ISO 15002:2008/A1:2020EN ISO 15002:2008/A1:2020
PreviousNext
Amendment
EN ISO 15002:2008/A1:2020
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-februar-2020
Pretočni merilniki za priključitev na končne dele napeljav za medicinske pline -
Dopolnilo A1 (ISO 15002:2008/Amd 1:2018)
Flow-metering devices for connection to terminal units of medical gas pipeline systems -
Amendment 1 (ISO 15002:2008/Amd 1:2018)
Durchflussmesseinrichtungen zum Anschluss an Entnahmestellen von
Rohrleitungssystemen für medizinische Gase - Änderung 1 (ISO 15002:2008/Amd
1:2018)
Dispositifs de mesure de débit pour raccordement aux prises murales des systèmes de
distribution de gaz médicaux - Amendement 1 (ISO 15002:2008/Amd 1:2018)
Ta slovenski standard je istoveten z: EN ISO 15002:2008/A1:2019
ICS:
11.040.10 Anestezijska, respiratorna in Anaesthetic, respiratory and
reanimacijska oprema reanimation equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 15002:2008/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2019
EUROPÄISCHE NORM
ICS 11.040.10
English Version
Flow-metering devices for connection to terminal units of
medical gas pipeline systems - Amendment 1 (ISO
15002:2008/Amd 1:2018)
Dispositifs de mesure de débit pour raccordement aux Durchflussmesseinrichtungen zum Anschluss an
prises murales des systèmes de distribution de gaz Entnahmestellen von Rohrleitungssystemen für
médicaux - Amendement 1 (ISO 15002:2008/Amd medizinische Gase - Änderung 1 (ISO
1:2018) 15002:2008/Amd 1:2018)
This amendment A1 modifies the European Standard EN ISO 15002:2008; it was approved by CEN on 4 November 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15002:2008/A1:2019 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 15002:2008/A1:2019) has been prepared by Technical Committee ISO/TC 121
"Anaesthetic and respiratory equipment" in collaboration with Technical Committee CEN/TC 215
“Respiratory and anaesthetic equipment” the secretariat of which is held by BSI.
This Amendment to the European Standard EN ISO 15002:2008 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by May 2020, and
conflicting national standards shall be withdrawn at the latest by May 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Mac
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 16571:2024(Main)
Systems for evacuation of plume generated by medical devices (ISO 16571:2024)
EN ISO 16571:2024

Full revision of currently published 2014 version.  Additionally, expand scope to include plume evacuation systems for endoscopic procedures (e.g. minimally invasive, laparoscopic).
The scope is now the following:
This Standard specifies requirements and guidelines for the design, manufacture, installation, function, performance, maintenance, servicing, documentation, testing, and commissioning of equipment for evacuation of plume generated by medical devices. It is applicable to:
a) portable and mobile plume evacuation systems,
b) local stationary plume evacuation systems,
c) dedicated central pipeline systems for plume evacuation systems, and
d) plume evacuation systems integrated into other equipment (e.g. laser equipment).

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 81060-2:2020/A2:2024(Amendment)
Non-invasive sphygmomanometers - Part 2: Clinical investigation of intermittent automated measurement type - Amendment 2 (ISO 81060-2:2018/Amd 2:2024)
EN ISO 81060-2:2019/A2:2024
  • Amendment
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 15002:2024(Main)
Flow control devices for connection to a medical gas supply system (ISO 15002:2023)
EN ISO 15002:2024

This document specifies requirements for flow control devices that can be connected by the user either directly, by means of a probe or a gas-specific connector, or indirectly by means of a low-pressure hose assembly conforming with ISO 5359 to:
a)    a terminal unit conforming with ISO 9170-1 of a medical gas pipeline system conforming with ISO 7396-1:2016;
b)    the pressure outlet of a regulator conforming with ISO 10524-1:2018; or
c)    to the pressure outlet of a valve integrated pressure regulator (VIPR) conforming with ISO 10524-3 (see 5.2 gas inlets).
This document applies to the following types of flow control devices (FCDs):
a)    flowmeters;
b)    flowgauge FCDs; and
c)    fixed orifice FCDs.
NOTE       Flow control devices that are classed as medical electrical equipment can be subject to additional requirements of IEC 60601-1.
This document applies to flow control devices for the following gases:
—    oxygen;
—    oxygen 93 %;
—    nitrous oxide;
—    medical air;
—    carbon dioxide;
—    oxygen/nitrous oxide mixture 50/50 (% volume fraction);
—    oxygen-enriched air;
—    helium;
—    xenon; and
—    specified mixtures of the gases listed above.
NOTE Flow control devices can be available for other gases.
This document does not apply to flow control devices that are:
a)    for use with gases for driving surgical tools;
b)    an integral part of a regulator (see ISO 10524-1:2018); or
c)           an integral part of a valve with integrated pressure regulator (VIPR) (see ISO 10524-3).

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80601-2-12:2024(Main)
Medical electrical equipment - Part 2-12: Particular requirements for basic safety and essential performance of critical care ventilators (ISO 80601-2-12:2023)
EN ISO 80601-2-12:2023

This document applies to the basic safety and essential performance of a critical care ventilator in
combination with its accessories, hereafter referred to as ME equipment:
 intended for use in an environment that provides specialized care for patients whose conditions can
be life-threatening and who can require comprehensive care and constant monitoring in a
professional healthcare facility;
NOTE 2 For the purposes of this document, such an environment is referred to as a critical care
environment. Ventilators for this environment are considered life-sustaining.
NOTE 3 For the purposes of this document, such a critical care ventilator can provide ventilation during
transport within a professional healthcare facility (i.e. be a transit-operable ventilator).
NOTE 4 A critical care ventilator intended for use in transport within a professional healthcare facility is not
considered as an emergency medical services environment ventilator.
 intended to be operated by a healthcare professional operator; and
 intended for those patients who need differing levels of support from artificial ventilation including
for ventilator-dependent patients.
A critical care ventilator is not considered to use a physiologic closed-loop-control system unless it uses a
physiological patient variable to adjust the artificial ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to
a ventilator breathing system, or to a ventilator, where the characteristics of those accessories can affect
the basic safety or essential performance of the ventilator.NOTE 5 If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems
only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause
applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the
scope of this document are not covered by specific requirements in this document except in IEC 60601-
1:2005+AMD1:2012+AMD2:2020, 7.2.13 and 8.4.1.
NOTE 6 Additional information can be found in IEC 60601-1:2005+AMD1:2012+AMD2:2020, 4.2.
This document is not applicable to ME equipment or an ME system operating in a ventilator-operational
mode solely intended for patients who are not dependent on artificial ventilation.
NOTE 7 A critical care ventilator, when operating in such a ventilator-operational mode, is not considered lifesustaining.
This document is not applicable to ME equipment that is intended solely to augment the ventilation of
spontaneously breathing patients within a professional healthcare facility.
This document does not specify the requirements for:
NOTE 8 See ISO/TR 21954 for guidance on the selection of the appropriate ventilator for a given patient.
 ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601-2-13;
 ventilators or accessories intended for the emergency medical services environment, which are given
in ISO 80601-2-84;
 ventilators or accessories intended for ventilator-dependent patients in the home healthcare
environment, which are given in ISO 80601-2-72;
 ventilators or accessories intended for home-care ventilatory support devices, which are given in
ISO 80601-2-79 and ISO 80601-2-80;
 obstructive sleep apnoea therapy ME equipment, which are given in ISO 80601-2-70;
 continuous positive airway pressure (CPAP) ME equipment.
 high-frequency ventilators, which are given in ISO 80601-2-87;
NOTE 9 A critical care ventilator can incorporate high-frequency jet or high-frequency oscillatory
ventilator-operational modes.
 respiratory high-flow therapy equipment, which are given in ISO 80601-2-90;
NOTE 10 A critical care ventilator can incorporate high-flow therapy operational mode, but such a mode is
only for spontaneously breathing

  • Standard
    168 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80601-2-84:2024(Main)
Medical electrical equipment - Part 2-84: Particular requirements for the basic safety and essential performance of ventilators for the emergency medical services environment (ISO 80601-2-84:2023)
EN ISO 80601-2-84:2023

This document applies to the basic safety and essential performance of an EMS ventilator in combination with its accessories, hereafter also referred to as ME equipment:
–   intended for patients who need differing levels of support from artificial ventilation including ventilator-dependent patients;
–   intended to be operated by a healthcare professional operator;
–   intended for use in the EMS environment; and
–   intended for invasive or non-invasive ventilation.
NOTE 1 An EMS ventilator can also be used for transport within a professional healthcare facility.
* An EMS ventilator is not considered to utilize physiologic closed loop-control system unless it uses a physiological patient variable to adjust the ventilation therapy settings.
This document is also applicable to those accessories intended by their manufacturer to be connected to the ventilator breathing system, or to an EMS ventilator, where the characteristics of those accessories can affect the basic safety or essential performance of the EMS ventilator.
NOTE 2 If a clause or subclause is specifically intended to be applicable to ME equipment only, or to ME systems only, the title and content of that clause or subclause will say so. If that is not the case, the clause or subclause applies both to ME equipment and to ME systems, as relevant.
Hazards inherent in the intended physiological function of ME equipment or ME systems within the scope of this document are not covered by specific requirements in this document except in IEC 60601-1:2005, 7.2.13 and 8.4.1.
NOTE 3 Additional information can be found in IEC 60601-1:2005+AMD1:2012, 4.2.
This document does not specify the requirements for the following:
–   ventilators or accessories intended for ventilator-dependent patients in critical care applications, which are given in ISO 80601-2-12.
–   ventilators or accessories intended for ventilator-dependent patients in the home healthcare environment, which are given in ISO 80601-2-72[3].
–   ventilators or accessories intended for anaesthetic applications, which are given in ISO 80601‐2‐13[4].
–   ventilators or accessories intended for ventilatory support equipment (intended only to augment the ventilation of spontaneously breathing patients), which are given in ISO 80601-2-79[5] and ISO 80601-2-80[6] 1.
–   obstructive sleep apnoea therapy ME equipment, which are given in ISO 80601‐2‐70[7].
–   operator-powered resuscitators, which are given in ISO 10651‐4[8].
–   gas-powered emergency resuscitators, which are given in ISO 10651‐5[9].
–   continuous positive airway pressure (CPAP) ME equipment .
–   high‐frequency jet ventilators (HFJVs), which are given ISO 80601-2-87[11].
–   high‐frequency oscillatory ventilators (HFOVs)[10], which are given ISO 80601-2-87[11].
–   NOTE 4 An EMS ventilator can incorporate high-frequency jet or high-frequency oscillatory ventilation-modes.
–   cuirass or “iron‐lung” ventilators.

  • Standard
    149 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80601-2-55:2018/A1:2024(Amendment)
Medical electrical equipment - Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors - Amendment 1 (ISO 80601-2-55:2018/Amd 1:2023)
EN ISO 80601-2-55:2018/A1:2023
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 10524-1:2019/A1:2024(Amendment)
Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices - Amendment 1 (ISO 10524-1:2018/Amd 1:2023)
EN ISO 10524-1:2019/A1:2023
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5367:2023(Main)
Anaesthetic and respiratory equipment - Breathing sets and connectors (ISO 5367:2023)
EN ISO 5367:2023

This document specifies minimum requirements for breathing sets and breathing tubes intended to be used with anaesthetic breathing systems, ventilator breathing systems, humidifiers or nebulizers. It applies to breathing sets and breathing tubes and patient end adaptors supplied already assembled and to those supplied as components and assembled in accordance with the manufacturer’s instructions.
This document is applicable to breathing sets which include special components (e.g. water traps) between the patient end and machine end.
Provision is made for coaxial and related bifurcated, double-lumen, or multiple-lumen breathing sets and breathing tubes suitable for use with patient end adaptors.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80601-2-72:2023(Main)
Medical electrical equipment - Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients (ISO 80601-2-72:2023)
EN ISO 80601-2-72:2023

ISO 80601-2-72:2015 applies to the basic safety and essential performance of a ventilator in combination with its accessories, hereafter referred to as me equipment:
intended for use in the home healthcare environment;
intended for use by a lay operator;
intended for use with patients who are dependent on mechanical ventilation for their life support.
ISO 80601-2-72:2015 is also applicable to those accessories intended by their manufacturer to be connected to a ventilator breathing system or to a ventilator where the characteristics of those accessories can affect the basic safety or essential performance of the ventilator.
ISO 80601-2-72:2015 is a particular International Standard in the IEC 60601‑1 and ISO/IEC 80601 series of standards.

  • Standard
    152 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 27427:2023(Main)
Anaesthetic and respiratory equipment - Nebulizing systems and components (ISO 27427:2023)
EN ISO 27427:2023

This document specifies requirements for the safety and performance testing of general-purpose nebulizing systems intended for continuous or breath-actuated delivery of liquids, in aerosol form, to humans through the respiratory system.
This document includes gas-powered nebulizers (which can be powered by, e.g., compressors, pipeline systems, cylinders, etc.) and electrically powered nebulizers [e.g. spinning disc, ultrasonic, vibrating mesh (active and passive), and capillary devices] or manually powered nebulizers. This document does not specify the electrical requirements of electrically powered nebulizers.
This document does not specify the minimum performance of nebulizing systems.
This document does not apply to:
a)       devices intended for nasal deposition;
b)       devices intended solely to provide humidification or hydration by providing water in aerosol form.
NOTE 1        ISO 80601-2-74 and ISO 20789 cover these devices.
c)        drug-specific nebulizers or their components (e.g. metered dose inhalers, metered liquid inhalers, dry powder inhalers).
NOTE 2        ISO 20072 covers these devices.
NOTE 3        See Annex A for rationale.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day