iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 50157-2-2:2001

(Main)

Domestic and similar electronic equipment interconnection requirements: AV.link -- Part 2-2: Basic system oriented commands

Domestic and similar electronic equipment interconnection requirements: AV.link -- Part 2-2: Basic system oriented commands

AV.link devices may communicate with each other in AV.link mode 2 by sending and receiving basic system oriented commands. The AV.link mode 2 communication takes place via the AV.link on contact 10 of the peri-television connector as specified in EN 50049-1. By sending AV.link system oriented commands a device may control some basic functions of other devices. For instance an AV.link television may control some functions of an AV.link Video Cassette Recorder. This document specifies the AV.link communication protocols and the basic AV.link commands within mode 2

Kennwerte für die Kleinsignalverbindung zwischen elektronischen Geräten für den Heimgebrauch und ähnliche Anwendungen: AV.link -- Teil 2-2: Grundlegende systemorientierte Befehle

Spécification des interconnexions des équipements électroniques domestiques et à usage analogue: AV.link -- Partie 2-2: Commandes de base du système

Domestic and similar electronic equipment interconnection requirements: AV link - Part 2-2: Basic system oriented comma

General Information

Status
Published
Publication Date
28-Feb-2001
ICS
33.160.40 - Video systems
Technical Committee
AVM - Audio, video and multimedia systems and equipment
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Mar-2001
Due Date
01-Mar-2001
Completion Date
01-Mar-2001
Ref Project
EN 50157-2-2:1998 - Domestic and similar electronic equipment interconnection requirements: AV.link - Part 2-2: Basic system oriented commands

Buy Standard

EN 50157-2-2:2001EN 50157-2-2:2001
PreviousNext
Standard
EN 50157-2-2:2001
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50157-2-2:2001
01-marec-2001
Domestic and similar electronic equipment interconnection requirements: AV link -
Part 2-2: Basic system oriented comma
Domestic and similar electronic equipment interconnection requirements: AV.link -- Part
2-2: Basic system oriented commands
Kennwerte für die Kleinsignalverbindung zwischen elektronischen Geräten für den
Heimgebrauch und ähnliche Anwendungen: AV.link -- Teil 2-2: Grundlegende
systemorientierte Befehle
Spécification des interconnexions des équipements électroniques domestiques et à
usage analogue: AV.link -- Partie 2-2: Commandes de base du système
Ta slovenski standard je istoveten z: EN 50157-2-2:1998
ICS:
33.160.40 Video sistemi Video systems
SIST EN 50157-2-2:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50157-2-2:2001

---------------------- Page: 2 ----------------------

SIST EN 50157-2-2:2001

---------------------- Page: 3 ----------------------

SIST EN 50157-2-2:2001

---------------------- Page: 4 ----------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 63005-2:2020(Main)
Event video data recorder for road vehicle accidents - Part 2: Test methods for evaluating the performance of basic functions (IEC 63005-2:2019)
EN IEC 63005-2:2020

This part of IEC 63005 describes test methods on evaluating performance of basic
functionalities of EVDR described in IEC 63005-1.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 63005-1:2018(Main)
Event video data recorder for road vehicle accidents - Part 1: Basic requirements (IEC 63005-1:2017)
EN 63005-1:2017

This part of IEC 63005 describes basic requirements for event video data recorders (EVDRs)
for road vehicle accidents, used for identifying and analysing causes of accidents based on
video from a front-mounted camera and other information obtained before and after such
events. In addition to video from a front-mounted camera and vehicle behaviour, these
products can record side and/or rear video data for enhanced functionalities in determining
causes of accidents and analysing collision events.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62087-4:2016(Main)
Audio, video, and related equipment - Determination of power consumption - Part 4: Video recording equipment (IEC 62087-4:2015)
EN 62087-4:2016

This part of IEC 62087 specifies methods of measurement for the power consumption of video
recording equipment with removable media. It specifies the different modes of operation which
are relevant for measuring power consumption.
The methods of measurement are applicable only for equipment which can be connected to
the mains.
The measuring conditions in this standard represent the normal use of the equipment and
may differ from specific conditions, as specified, for example, in safety standards.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62379-3:2015(Main)
Common control interface for networked digital audio and video products -- Part 3: Video (TA 4) (IEC 62379-3:2015)
EN 62379-3:2015

This part of IEC 62379 details aspects of the common control interface specified in
IEC 62379-1 that are specific to video.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61883-8:2009/A1:2014(Amendment)
Consumer audio/video equipment - Digital interface -- Part 8: Transmission of ITU-R BT.601 style digital video data (IEC 61883-8:2008/A1:2014)
EN 61883-8:2009/A1:2014

This part of IEC 61883 specifies a protocol for the transport of uncompressed or compressed video data in the 4:2:2 format of recommendation ITU-R BT.601 (including compatible extensions to this format for the higher and lower resolutions of other commonly used video resolutions) over high performance serial bus, as specified by IEEE Std 1394-1995 as amended by IEEE Std 1394a-2000 and IEEE Std 1394b-2002 (collectively IEEE 1394). The
data formats for the encapsulation of video data are compatible with those specified by IEC 61883-1. Associated audio data, if any, should be formatted as specified by IEC 61883-6. There are many commonly used video formats unsupported by IEC 61883, such as MPEG-4, Windows Media Format (WMF) and the format used by automotive navigation applications. Support for all or most of these formats in rendering devices would require implementation of multiple video codecs. This is an undue burden that may be avoided if the source device converts to ITU-R BT.601 4:2:2 format and, if necessary, compresses the data with a codec supported by all destination devices. An additional advantage is that on-screen display (OSD) information may be mixed with video data prior to transmission to the rendering device. Because ITU-R BT.601 4:2:2 format is widely used internally in contemporary AV equipment, this specification permits straight-forward integration of IEEE 1394 into these devices and enables markets whose usage scenarios include single video sources transmitting to one or more video displays, such as:
– consumer electronic STB or DVD video rendered by multiple displays in the home;
– automotive navigation and entertainment; and
– aeronautical in-flight entertainment.
For the sake of interoperability and bounded implementation complexity, it is essential that the specification provide the following:
– a 1394 TA controlled list of compression codecs; and
– at a minimum, a reference to one video compression codec.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61834-4:1999/A1:2011(Main)
Recording - Helical-scan digital video cassette recording system using 6,35 mm magnetic tape for consumer use (525-60, 625-50, 1125-60 and 1250-50 systems) - Part 4: Pack header table and contents (IEC 61834-4:1998/A1:2010)
EN 61834-4:1998/A1:2011

Specifies the pack headers and the contents of packs which are applicable to the whole recording system of helical-scan digital video cassette using 6,35 mm magnetic tape.

  • Amendment
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60461:2011(Main)
Time and control code (IEC 60461:2010)
EN 60461:2011

This International Standard specifies a digital time and control code for use in television, film, and accompanying audio systems operating at nominal rate of 60, 59,94, 50, 30, 29,97, 25, 24 and 23,98 frames per second. This International Standard specifies a time address, binary groups, and flag bit structure. In addition, the standard specifies a binary group flag assignment, a linear time code transport, and a vertical interval time code transport.
This International Standard defines primary data transport structures for linear time code (LTC) and vertical interval time code (VITC). This standard specifies the LTC modulation and timing for all video formats. This standard also defines the VITC modulation and location for 525/59,94 and 625/50 analogue composite and component systems only.
NOTE The digital representation of analogue VITC (D-VITC) is specified in SMPTE 266M and is defined for 525/59,94 and 625/50 digital component systems only. High definition formats, such as those documented in SMPTE 274M and SMPTE 296M, should use ancillary time code (ATC) as specified in SMPTE 12M-2 (formerly SMPTE RP 188) for transport of time code in the digital video data stream. For future implementations of time code for digital standard definition formats, the use of ATC rather than D-VITC is encouraged.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61883-8:2009
Consumer audio/video equipment - Digital interface - Part 8: Transmission of ITU-R BT.601 style digital video data (IEC 61883-8:2008)
EN 61883-8:2009

This part of IEC 61883 specifies a protocol for the transport of uncompressed or compressed video data in the 4:2:2 format of recommendation ITU-R BT.601 (including compatible extensions to this format for the higher and lower resolutions of other commonly used video resolutions) over high performance serial bus, as specified by IEEE Std 1394-1995 as amended by IEEE Std 1394a-2000 and IEEE Std 1394b-2002 (collectively IEEE 1394). The data formats for the encapsulation of video data are compatible with those specified by IEC 61883-1. Associated audio data, if any, should be formatted as specified by IEC 61883-6. There are many commonly used video formats unsupported by IEC 61883, such as MPEG-4, Windows Media Format (WMF) and the format used by automotive navigation applications.
Support for all or most of these formats in rendering devices would require implementation of multiple video codecs. This is an undue burden that may be avoided if the source device converts to ITU-R BT.601 4:2:2 format and, if necessary, compresses the data with a codec supported by all destination devices. An additional advantage is that on-screen display (OSD) information may be mixed with video data prior to transmission to the rendering device. Because ITU-R BT.601 4:2:2 format is widely used internally in contemporary AV equipment, this specification permits straight-forward integration of IEEE 1394 into these devices and
enables markets whose usage scenarios include single video sources transmitting to one or more video displays, such as: - consumer electronic STB or DVD video rendered by multiple displays in the home; - automotive navigation and entertainment; and - aeronautical in-flight entertainment. For the sake of interoperability and bounded implementation complexity, it is essential that the specification provide the following: - a 1394 TA controlled list of compression codecs; and - at a minimum, a reference to one video compression codec.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61834-11:2008(Main)
Recording - Helical-scan digital video cassette recording system using 6,35 mm magnetic tape for consumer use (525-60, 625-50, 1125-60 and 1250-50 systems) -- Part 11: HDV format for 1080i and 720p systems
EN 61834-11:2008

This part of IEC 61834 specifies the content, format, and recording method of data blocks containing video, audio, and system data on the helical scan digital video cassettes using 6,35 mm tape as defined in IEC 61834-1 for recording MPEG-2 streaming HD signals. The MPEG-2 streaming HD signals defined in this standard have the following modes. The HD1 mode is designed for the following systems: - 525-line progressive with a frame frequency of 59,94 Hz (hereinafter referred to as 480p/60 system) - 625-line progressive with a frame frequency of 50,00 Hz (hereinafter referred to as 576p/50 system) - 525-line interlace with a field frequency of 59,94 Hz (hereinafter referred to as 480i/60 system) - 625-line interlace with a field frequency of 50,00 Hz (hereinafter referred to as 576i/50 system) - 525-line progressive with a frame frequency of 29,97 Hz (hereinafter referred to as 480p/30 system) - 625-line progressive with a frame frequency of 25,00 Hz (hereinafter referred to as 576p/25 system) - 750-line progressive with a frame frequency of 29,97 Hz (hereinafter referred to as 720p/30 system) - 750-line progressive with a frame frequency of 25,00 Hz (hereinafter referred to as 720p/25 system) - 750-line progressive with a frame frequency of 59,94 Hz (hereinafter referred to as 720p/60 system) - 750-line progressive with a frame frequency of 50,00 Hz (hereinafter referred to as 720p/50 system) The main specifications shall be as defined in IEC 61834-9 and IEC 61834-10.. Other information, such as details about MPEG-2 stream descriptors, trick play data, system data, etc., are defined in Clause 7. The HD2 mode is designed for the following systems: - 1125-line interlace with a field frequency of 59,94 Hz (hereinafter referred to as 1080i/60 system) - 1125-line interlace with a field frequency of 50,00 Hz (hereinafter referred to as 1080i/50 system) The main specifications for helical recordings and the program track data format shall be as defined in Clauses 5 and 6 of thisstandard. Other information, such as details about main data, PES data, search data, subcode data, MPEG-2 stream descriptors, etc., are defined in Clause 8.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62071-3:2007(Main)
Helical-scan compressed digital video cassette system using 6,35 mm magnetic tape - Format D-7 -- Part 3: Data stream format
EN 62071-3:2006

This part of IEC 62071 defines the format of the data stream for the synchronous exchange of DV-based audio, data, and compressed video (whose data structure is defined in SMPTE 314M) over the interface defined in SMPTE 305M. It covers the transmission of audio, subcode data and compressed video packets associated with DV-based 25 and 50 Mb/s data structures including faster-than-real-time transmission for 525/60 SDTI and 625/50 SDTI systems. This standard does not include the data stream of a DV-compressed structure as defined in SMPTE 322M. Space within SMPTE 305M not used by a data stream conforming to this standard may be used for the transmission of data other than those representing DV-based audio, data and compressed video. In this standard, the 60 Hz system refers to the field frequency 59,94 Hz system and the 50 Hz system refers to the field frequency 50,0 Hz system.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day