SIST EN 4611-003:2019
(Main)Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Part 003: Tin plated copper - Operating temperatures, between -65 °C and 135 °C - Single extruded wall for enclosed applications - UV laser printable - Product standard
Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Part 003: Tin plated copper - Operating temperatures, between -65 °C and 135 °C - Single extruded wall for enclosed applications - UV laser printable - Product standard
This European Standard specifies the characteristics of UV laser printable, tin plated copper conductor electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on-board electrical systems of aircraft operating at temperatures between – 65 °C and 135 °C. The voltage rating is 600 Vrms at sea level. This insulation system has been used in aerospace applications using 115 Vac (phase-to-neutral) 400 Hz and 28 Vdc. Verification of the suitability of cables for use in other electrical systems is the responsibility of the user.
These cables are only suitable for airframe use with additional protection against mechanical abuse. In case of conflict between this standard and other referenced documents the requirements of this standard shall take precedence.
Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen für allgemeine Verwendung - XLETFE Familie - Teil 003: Kupfer verzinnt - Betriebstemperaturen zwischen -65 °C und 135 °C - Einfach extrudierte Isolierung für interne Verwendung - UV-Laser bedruckbar - Produktnorm
Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Partie 003: Cuivre étamé - Températures de fonctionnement comprises entre -65 °C et 135 °C - Fil simple isolé pour applications internes - Marquable au laser UV - Norme de produit
La présente Norme européenne spécifie les caractéristiques des conducteurs en cuivre étamé, marquables au laser UV, de la famille des copolymères éthylènes tétrafluoroéthylènes réticulés (XLETFE) utilisés dans les systèmes électriques de bord des aéronefs à une température de fonctionnement comprise entre – 65 °C et 135 °C. La tension nominale est de 600 V rms au niveau de la mer. Ce système d'isolation a été employé dans des applications aérospatiales en utilisant 115 V ca (phase à neutre) 400 Hz et 28 V cc. La vérification de l'aptitude des câbles à être utilisés dans d'autres systèmes électriques relève de la responsabilité de l'utilisateur.
Ces câbles conviennent uniquement pour une utilisation en cellule s'ils ont une protection supplémentaire contre les contraintes mécaniques. En cas de conflit entre la présente Norme et d’autres documents de référence, les exigences de la présente Norme doivent être prises en première considération.
Aeronavtika - Kabli, električni, za splošne namene, eno- in večžilni - Družina XLETFE - 003. del: Pocinjeni baker - Obratovalne temperature med –65 °C in 135 °C - Enojno ekstrudirana izolacija za notranjo uporabo - Možnost UV-laserskega tiskanja - Standard za proizvod
Ta evropski standard določa lastnosti električnih kablov, potiskljivih z UV-laserjem, z vodnikom iz pocinjenega bakra iz družine kopolimerov, pridobljenih z mrežno polimerizacijo etilena in tetrafluoroetilena (XLETFE), za uporabo v električnih sistemih na krovu letal pri obratovalnih temperaturah med –65 in 135 °C. Nazivna napetost je 600 V RMS na morski gladini. Ta izolacijski sistem se je uporabljal v aeronavtiki pri izmenični napetosti 115 V (za fazno napetost) pri 400 Hz in 28 V pri enosmerni napetosti. Za preverjanje ustreznosti kablov za uporabo v drugih električnih sistemih je odgovoren uporabnik.
Ti kabli so primerni samo za uporabo na ogrodjih letal z dodatno zaščito pred mehansko obrabo. V primeru neskladja med tem standardom in drugimi navedenimi dokumenti imajo prednost določila tega standarda.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.ODVHUVNHJDLuft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen für allgemeine Verwendung - XLETFE Familie - Teil 003: Kupfer verzinnt - Betriebstemperaturen zwischen -65 °C und 135 °C - Einfach extrudierte Isolierung für interne Verwendung - UV-Laser bedruckbar - ProduktnormSérie aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Partie 003: Cuivre étamé - Températures de fonctionnement comprises entre -65 °C et 135 °C - Fil simple isolé pour applications internes - Marquable au laser UV - Norme de produitAerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Part 003: Tin plated copper - Operating temperatures, between -65 °C and 135 °C - Single extruded wall for enclosed applications - UV laser printable - Product standard49.060Aerospace electric equipment and systems29.060.20KabliCablesICS:Ta slovenski standard je istoveten z:EN 4611-003:2018SIST EN 4611-003:2019en,fr,de01-februar-2019SIST EN 4611-003:2019SLOVENSKI
STANDARDSIST EN 4611-003:20121DGRPHãþD
SIST EN 4611-003:2019
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4611-003
December
t r s z ICS
v {ä r x r Supersedes EN
v x s sæ r r uã t r s tEnglish Version
Aerospace series æ Cablesá electricalá for general purposeá single and multicore assembly æ XLETFE Family æ Part
r r uã Tin plated copper æ Operating temperaturesá between æ x w
¹C and
s u w
¹C æ Single extruded wall for enclosed applications æ UV laser printable æ Product standard Série aérospatiale æ Câblesá électriquesá d 5usage généralá mono et multiconducteurs æ Famille XLETFE æ Partie
r r uã Cuivre étamé æ Températures de fonctionnement comprises entre æ x w
¹C et
s u w
¹C æ Fil simple isolé pour applications internes æ Marquable au laser UV æ Norme de produit
Luftæ und Raumfahrt æ Einæ und mehradrige elektrische Leitungen für allgemeine Verwendung æ XLETFE Familie æ Teil
r r uã Kupferverzinnt æ Betriebstemperaturen zwischen æ x w
¹C und
s u w
¹C æ Einfach extrudierte Isolierung für interne Verwendung æ UVæLaser bedruckbar æ Produktnorm This European Standard was approved by CEN on
x August
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v x s sæ r r uã t r s z ESIST EN 4611-003:2019
EN 4611-003:2018 (E) 2 Contents
Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms, definitions, symbols and abbreviations . 4 4 Materials and construction . 4
w Required characteristics . 6 6 Quality assurance . 10 7 Designation . 10 8 Identification and marking . 10 9 Packaging, labelling and delivery lengths . 11 10 Technical specification . 11
SIST EN 4611-003:2019
EN 4611-003:2018 (E) 3 European foreword This document (EN 4611-003:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be withdrawn at the latest by June 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 4611-003:2012. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 4611-003:2019
EN 4611-003:2018 (E) 4 1 Scope This European Standard specifies the characteristics of UV laser printable, tin plated copper conductor electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on-board electrical systems of aircraft operating at temperatures between – 65 °C and 135 °C. The voltage rating is 600 Vrms at sea level. This insulation system has been used in aerospace applications using 115 Vac (phase-to-neutral) 400 Hz and 28 Vdc. Verification of the suitability of cables for use in other electrical systems is the responsibility of the user. These cables are only suitable for airframe use with additional protection against mechanical abuse. In case of conflict between this standard and other referenced documents the requirements of this standard shall take precede
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.