SIST EN 1218-4:2004/kprA2:2009
(Amendment)Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines fed by chain(s)
Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines fed by chain(s)
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 4: Kantenanleimmaschinen mit Kettenbandvorschub
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 4: Machines à plaquer sur chant à chaîne(s)
Varnost lesnoobdelovalnih strojev - Stroji za izdelovanje čepov in utorov - 4. del: Stroji za upogibanje z verižnim podajanjem
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 1218-4:2004/kprA2:2009
01-februar-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY6WURML]DL]GHORYDQMHþHSRYLQXWRURYGHO
6WURML]DXSRJLEDQMH]YHULåQLPSRGDMDQMHP
Safety of woodworking machines - Tenoning machines - Part 4: Edge banding machines
fed by chain(s)
Sicherheit von Holzbearbeitungsmaschinen - Zapfenschneid- und Schlitzmaschinen -
Teil 4: Kantenanleimmaschinen mit Kettenbandvorschub
Sécurité des machines pour le travail du bois - Tenonneuses - Partie 4: Machines à
plaquer sur chant à chaîne(s)
Ta slovenski standard je istoveten z: EN 1218-4:2004/prA2
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1218-4:2004/kprA2:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1218-4:2004/kprA2:2009
---------------------- Page: 2 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 1218-4:2004
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
November 2008
ICS 79.120.10
English Version
Safety of woodworking machines - Tenoning machines - Part 4:
Edge banding machines fed by chain(s)
Sécurité des machines pour le travail du bois - Sicherheit von Holzbearbeitungsmaschinen -
Tenonneuses - Partie 4: Machines à plaquer sur chant à Zapfenschneid- und Schlitzmaschinen - Teil 4:
chaîne(s) Kantenanleimmaschinen mit Kettenbandvorschub
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A2, if approved, will modify the European Standard EN 1218-4:2004. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1218-4:2004/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EN 1218-4:2004/prA2:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to Clause 1, Scope.4
3 Modification to Clause 2, Normative references .4
4 Modification to 3.3, Definitions.5
5 Modification to Clause 4, List of hazards.5
6 Modification to 5.2.1, Safety and reliability of control systems.8
7 Modification to 5.2.3, Starting.8
8 Modification to 5.2.4.1, Normal stopping .8
9 Modification to 5.2.4.2, All other stop controls.8
10 Modification to 5.2.5, Emergency stop .8
11 Modification to 5.2.7.2, Mode selection for adjustment of tools and other processing units .8
12 Modification to 5.2.8, Speed changing .8
13 Modification to 5.2.10, Failure of the power supply .8
14 Modification to 5.2.11 Failure of the control circuits .8
15 Modification to 5.3.1, Stability .9
16 Modification to 5.3.2, Risk of break-up during operation .9
17 Modification to 5.3.3.2, Strength .9
18 Modification to 5.3.3.6, Spindle rings .9
19 Modification to 5.4.1, Fire.9
20 Modification to 5.4.4, Electricity.9
21 Modification to 5.4.5 Ergonomics and handling.9
22 Modification to 5.4.6, Lighting.10
23 Modification to 5.4.11, Radiation.10
24 Modification to 5.4.14, Isolation .10
25 Modification to 5.4.15, Maintenance .10
26 Modification to 6.2, Marking .11
27 Modification to 6.3, Instruction handbook .11
28 Modification to Annex A.12
29 Modification to Annex C.12
30 Modification to Annex ZA .12
31 Addition of Annex ZB .13
32 Modification to Bibliography .13
2
---------------------- Page: 4 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EN 1218-4:2004/prA2:2008 (E)
Foreword
This document (EN 1218-4:2004/prA2:2008) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of the Machinery Directive.
For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this
document.
This document includes Amendment A.2, approved by CEN on XXXX-XX-XX.
The main changes compared to the previous version are:
- Addition of Annex ZB
- Editorial modification of Annex ZA
- “Minor” changes of sub-clauses 1, 2, 3.3, 4, 5.2.1, 5.2.3, 5.2.4.1, 5.2.4.2, 5.2.5, 5.2.7.2, 5.2.8, 5.2.10,
5.2.11, 5.3.1, 5.3.2, 5.3.3.2, 5.3.3.6, 5.4.1, 5.4.4, 5.4.6, 5.4.14, 5.4.15, 6.2, 6.3, Annex A, Annex C,
Bibliography
- Technical changes of sub-clauses 5.4.5, 5.4.11
3
---------------------- Page: 5 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EN 1218-4:2004/prA2:2008 (E)
1 Modification to the Foreword
Replace the fourth paragraph with the following:
"For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
2 Modification to Clause 1, Scope
Replace the 1st paragraph with the following: "This document deals with the significant hazards, hazardous
situations and events as listed in Clause 4 which are relevant to edge banding machines fed by chain(s)
where the loading and unloading is manual and where the maximum work-piece height capacity is 75 mm.
The machine is designed to process in one pass, one end (single end machine) or both ends (double end
machine) of solid wood, chipboard, fibreboard or plywood and also these materials where they are covered
with plastic laminate or edgings. The work-piece is fed through the processing units by an integrated feed. For
the purpose of this document an edge banding machine fed by chain(s) is hereinafter referred to as the
machine."
nd
Delete the 2 paragraph.
3 Modification to Clause 2, Normative references
Delete reference to EN 294:1992.
Replace reference to EN 418:1992 with: "EN ISO 13850:2008, Safety of machinery — Emergency stop —
st
Principles for design (ISO 13850:2006)" and replace "EN 418:1992" in 5.2.5, 1 paragraph, with
"EN ISO 13850:2008".
Replace "EN 847-1:1997, Tools for woodworking - Safety requirements – Part 1: Milling tools and circular
sawblades" with "EN 847-1:2005, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular
saw blades" and "EN 847-1:1997" with "EN 847-1:2005" throughout the document.
Replace "EN 954:1996" with "EN ISO 13849-1:2008 Safety of machinery — Safety-related parts of control
systems — Part 1: General principles for design (ISO 13849-1:2006)" throughout the document.
Delete "EN 1070:1998" and replace it with "EN ISO 12100-1:2003" throughout the document.
Replace "EN 60204-1:1992" with "EN 60204-1:2006" and replace in the title
"(IEC 60204-1:1992, modified)" with "(IEC 60204-1:2005, modified)".
Replace "EN 60947-4-1:1992" with "EN 60947-4-1:2001" throughout the document and replace in the title
"(IEC 60947-4-1:1990)" with "(IEC 60947-4-1:2000)".
Replace "EN 60947-5-1:1997" with "EN 60947-5-1:2004" throughout the document and replace in the title
"(IEC 60947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Replace "CEN/TS 61496-2:2003" with "CLC/TS 61496-2:2006" in Clause 2 and "prEN 61496-2" with "CLC/TS
rd
61496-2:2006" throughout the document and the 3 element of the title with "Part 2: Particular requirements
for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)".
Replace reference to "HD 21.1 S3:1997" with "HD 21.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having thermoplastic insulation — Part 1: General requirements" and replace "HD 21.1
S3:1997" with "HD 21.1 S4:2002" throughout the document.
4
---------------------- Page: 6 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EN 1218-4:2004/prA2:2008 (E)
Replace reference to "HD 22.1 S3:1997" with "HD 22.1 S4:2002, Cables of rated voltages up to and including
450/750 V and having cross-linked insulation — Part 1: General requirements" and replace "HD 22.1
S3:1997" with "HD 22.1 S4:2002" throughout the document.
Add the following references:
"EN 614-1:2006, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general
principles",
"EN 894-1:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 2: Displays
EN 894-3:2000, Safety of machinery — Ergonomics requirements for the design of displays and control
actuators — Part 3: Control actuators",
"EN 1005-1:2001, Safety of machinery — Human physical performance — Part 1: Terms and definitions
EN 1005-2:2003, Safety of machinery — Human physical performance — Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002, Safety of machinery — Human physical performance — Part 3: Recommended force limits
for machinery operation
EN 1005-4:2005, Safety of machinery — Human physical performance — Part 4: Evaluation of working
postures and movements in relation to machinery"
"EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 1: Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine-tools —
Part 2: Immunity",
"EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999)",
"EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for
visual, acoustic and tactile signals (IEC 61310-1:2007)"
4 Modification to 3.3, Definitions
Definition 3.3.11, replace the term with "displaceable machine".
Definition 3.3.12, replace the term with "information from the supplier".
5 Modification to Clause 4, List of hazards
Replace the heading of Clause 4 with: "List of significant hazards"
Replace the clause content with:
"This clause contains the significant hazards, hazardous situations and events (see EN 1050:1996) as far as
they are dealt with in this document, identified by risk assessment as significant for the machines as defined in
5
---------------------- Page: 7 ----------------------
SIST EN 1218-4:2004/kprA2:2009
EN 1218-4:2004/prA2:2008 (E)
the scope and which require action to eliminate or reduce the risk. This document deals with these significant
hazards by defining safety requirements and/or measures or by reference to relevant standards.
These hazards are listed in Table 1 in accordance with Annex A of EN 1050:1996.
Table 1 — List of significant hazards
Hazards, hazardous situations and Relevant sub-
No hazardous events EN ISO 12100 clause of this
document
Part 1: Part 2:
2003 2003
1 Mechanical hazards related to:
- machine parts or workpieces:
a) shape; 4.2 4.2.1, 5.3.3, 5.3.7,
4.2.2, 5 5.4.5, 5.4.9
b) relative location; 5.2.2, 5.2.5,
5.3.7
d) mass and velocity (kinetic energy of 5.2.7, 5.3.7
elements in controlled or uncontrolled
motion);
e) mechanical strength. 5.3.2, 5.3.3
- accumulation of energy inside the machinery:
g) liquids and gases under pressure; 4.2 4.10, 5.5.4 5.4.7, 5.4 8
1.1 Crushing hazard 4.2.1 5.3.7
1.2 Shearing hazard 5.3.7
1.3 Cutting or severing hazard 5.3.3, 5.3.4,
5.3.7
1.4 Entanglement hazard 5.3.3, 5.3.4,
5.3.6, 5.3.7
1.5 Drawing-in or trapping hazard 5.3.7
1.6 Impact hazard 5.3.7
1.8 Friction or abrasion hazard 5.3.4
1.9 High pressure fluid injection or ejection 5.3.4, 5.4.7,
hazard 5.4.8
2 Electrical hazards due to:
2.1 Contact of persons with live parts (direct 4.3 4.9, 5.5.4 5.4.4, 5.4.14
contact)
2.2 Contact of persons
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.