SIST EN ISO/IEC 17030:2009
(Main)Conformity assessment - General requirements for third-party marks of conformity (ISO/IEC 17030:2003)
Conformity assessment - General requirements for third-party marks of conformity (ISO/IEC 17030:2003)
This International Standard provides general requirements for third-party marks of conformity, including their issue and use.
Konformitätsbewertung - Allgemeine Anforderungen an Konformitätszeichen einer dritten Seite (ISO/IEC 17030:2003)
Diese Internationale Norm legt allgemeine Anforderungen an Konformitätszeichen einer dritten Seite fest, einschließlich deren Ausstellung und Verwendung.
ANMERKUNG Diese Internationale Norm kann auch als Leitlinie für die Verwendung von Konformitätszeichen in anderen Konformitätsbewertungstätigkeiten als der durch eine dritte Seite verwendet werden.
Évaluation de la conformité - Exigences générales pour les marques de conformité par tierce partie (ISO/IEC 17030:2003)
Ugotavljanje skladnosti - Splošne zahteve za znake skladnosti tretje stranke (ISO/IEC 17030:2003)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO/IEC 17030:2009
01-julij-2009
Ugotavljanje skladnosti - Splošne zahteve za znake skladnosti tretje stranke
(ISO/IEC 17030:2003)
Conformity assessment - General requirements for third-party marks of conformity
(ISO/IEC 17030:2003)
Konformitätsbewertung - Allgemeine Anforderungen an Konformitätszeichen einer dritten
Seite (ISO/IEC 17030:2003)
Évaluation de la conformité - Exigences générales pour les marques de conformité par
tierce partie (ISO/IEC 17030:2003)
Ta slovenski standard je istoveten z: EN ISO/IEC 17030:2009
ICS:
03.120.20 Certificiranje proizvodov in Product and company
podjetij. Ugotavljanje certification. Conformity
skladnosti assessment
SIST EN ISO/IEC 17030:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO/IEC 17030:2009
---------------------- Page: 2 ----------------------
SIST EN ISO/IEC 17030:2009
EUROPEAN STANDARD
EN ISO/IEC 17030
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2009
ICS 03.120.20
English version
Conformity assessment - General requirements for third-party
marks of conformity (ISO/IEC 17030:2003)
Évaluation de la conformité - Exigences générales pour les Konformitätsbewertung - Allgemeine Anforderungen an
marques de conformité par tierce partie (ISO/IEC Konformitätszeichen einer dritten Seite (ISO/IEC
17030:2003) 17030:2003)
This European Standard was approved by CEN on 7 May 2009.
CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
such national standards may be obtained on application to the CEN Management Centre or to any CEN or CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN and/or CENELEC member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN and CENELEC members are the national standards bodies and national electrotechnical committees, respectively, of Austria,
Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and
United Kingdom.
CEN Management Centre: CENELEC Central Secretariat:
Avenue Marnix 17, B-1000 Brussels Avenue Marnix 17, B-1000 Brussels
© 2009 CEN/CENELEC All rights of exploitation in any form and by any means reserved Ref. No. EN ISO/IEC 17030:2009 E
worldwide for CEN national Members and for CENELEC
Members.
---------------------- Page: 3 ----------------------
SIST EN ISO/IEC 17030:2009
EN ISO/IEC 17030:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO/IEC 17030:2009
EN ISO/IEC 17030:2009 (E)
Foreword
The text of ISO/IEC 17030:2003 has been prepared by Technical Committee ISO/CASCO “Committee on
conformity assessment” of the International Organization for Standardization (ISO) and the International
Electrotechnical Commission (IEC) and has been taken over as EN ISO/IEC 17030:2009 by Technical
Committee CEN/CENELEC/TC 1 “Criteria for conformity assessment bodies” the secretariat of which is held
by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn
at the latest by November 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO/IEC 17030:2003 has been approved by CEN as a EN ISO/IEC 17030:2009 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO/IEC 17030:2009
---------------------- Page: 6 ----------------------
SIST EN ISO/IEC 17030:2009
INTERNATIONAL ISO/IEC
STANDARD 17030
First edition
2003-10-01
Conformity assessment — General
requirements for third-party marks of
conformity
Évaluation de la conformité — Exigences générales pour les marques
de conformité par tierce partie
Reference number
ISO/IEC 17030:2003(E)
©
ISO 2003
---------------------- Page: 7 ----------------------
SIST EN ISO/IEC 17030:2009
ISO/IEC 17030:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO/IEC 17030:2009
ISO/IEC 17030:2003(E)
Foreword
ISO (the International Organization for Standardization) and IEC (the International Electrotechnical
Commission) form the specialized system for worldwide standardization. National bodies that are members of
ISO or IEC participate in the development of International Standards through technical committees
established by the respective organization to deal with particular fields of technical activity. ISO and IEC
technical committees collaborate in fields of mutual interest. Other international organizations, governmental
and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of conformity
assessment, the ISO Committee on conformity assessment (CASCO) is responsible for the development of
International Standards and Guides.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
Draft International Standards are circulated to the national bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the national bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/IEC 17030 was prepared by the ISO Committee on conformity assessment (CASCO).
It was circulated for voting to the national bodies of both ISO and IEC, and was approved by both
organizations.
© ISO 2003 — All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO/IEC 17030:2009
ISO/IEC 17030:2003(E)
Introduction
Marks of conformity take many forms and different uses. They can convey useful information about a product,
or indicate particular characteristics of a product such as its safety, quality, performance, reliability or impact
on the environment. They are found on products, certificates and publications denoting the conformity to
specified requirements of a product, management system, service, process, person or an organization. Most
important for all marks of conformity is to gain the confidence of the market, including consumers, in products
and other objects of conformity assessment to which these marks have been applied.
The prime purpose of this International Standard is to enable a uniform approach to the use of third-party
marks of conformity, to fill relevant gaps in existing ISO, IEC, ISO/IEC Standards and Guides, to address
potential problems arising from different uses of third-party marks of conformity, to provide a clear and rational
basis for their use, and to set out general requirements. This International Standard concentrates on third-
party marks of conformity but may also be used as guidance for other applications of marks of conformity.
This International Standard is based on market feedback and demands from various users and issuers of
marks of conformity assessment. It takes account of the ISO report on Marks of conformity assessment,
published in May 1999. The use of this International Standard should lead to improved market confidence,
international recognition and consumer acceptance of third-party marks of conformity.
iv © ISO 2003 — All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO/IEC 17030:2009
INTERNATIONAL STANDARD ISO/IEC 17030:2003(E)
Conformity assessment — General requirements for third-party
marks of conformity
1 Scope
This International Standard provides general requirements for third-party marks of conformity, including their
iss
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.