Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Part 002: General

This European Standard specifies the list of product standards and common characteristics of electrical cables for use in the on-board electrical systems of aircraft operating at temperatures between – 65 °C to 135 °C and 150 °C, dependent upon conductor type. The voltage rating is 600 V rms at sea level. This insulation system has been used in aerospace applications using 115 V ac (phase-to-neutral) 400 Hz and 28 V dc. Verification of the suitability of cables for use in other electrical systems is the responsibility of the user.

Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen zur allgemeines Verwendung - XLETFE Familie - Teil 002: Allgemeines

Diese Europäische Norm legt die Liste von Produktnormen sowie allgemeine Merkmale von elektrischen Leitungen zur Verwendung in der Bordelektrik von Luftfahrzeugen bei Betriebstemperaturen von −65 °C bis 135 °C und 150 °C, in Abhängigkeit vom Leitertyp, fest. Die Bemessungsspannung beträgt 600 V eff auf Meereshöhe. Dieses Isoliersystem wurde bei Luft  und Raumfahrtanwendungen mit 115 V Wechselstrom (Phase gegen Neutral), 400 Hz und 28 V Gleichstrom angewendet. Der Anwender ist für den Nachweis der Eignung von Leitungen zur Anwendung in anderen elektrischen Systemen verantwortlich.

Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Partie 002 : Généralités

La présente Norme européenne spécifie la liste des normes de produit et les caractéristiques communes des câbles électriques utilisés dans les systèmes électriques à bord des aéronefs à une température de fonctionnement comprise entre - 65 °C et 135 °C, et 150 °C selon le type de conducteur. La tension nominale est de 600 V rms au niveau de la mer. Ce système d’isolement a été utilisé dans les applications aérospatiales fonctionnant à 115 V ca (phase-neutre) 400 Hz et 28 V cc. Il incombe à l’utilisateur de vérifier si les câbles peuvent être utilisés dans d’autres systèmes électriques.

Aeronavtika - Kabli, električni, za splošne namene, eno- in večžilni - Družina XLETFE - 002. del: Splošno

Ta evropski standard določa seznam standardov za proizvod in skupnih značilnosti električnih kablov za uporabo v električnih sistemih na krovu letala pri obratovalnih temperaturah med –65 °C in 135 °C ter 150 °C, odvisno od vrste vodnika. Nazivna napetost je 600 V RMS na morski gladini. Ta izolacijski sistem se je uporabljal v aeronavtiki pri izmenični napetosti 115 V (za fazno napetost) pri 400 Hz in 28 V pri enosmerni napetosti. Za preverjanje ustreznosti kablov za uporabo v drugih električnih sistemih je odgovoren uporabnik.

General Information

Status
Published
Publication Date
16-Sep-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
31-Aug-2018
Due Date
05-Nov-2018
Completion Date
17-Sep-2018

RELATIONS

Buy Standard

Standard
SIST EN 4611-002:2018
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 4611-002:2018
01-november-2018
1DGRPHãþD
SIST EN 4611-002:2012
$HURQDYWLND.DEOLHOHNWULþQL]DVSORãQHQDPHQHHQRLQYHþåLOQL'UXåLQD
;/(7)(GHO6SORãQR

Aerospace series - Cables, electrical, for general purpose, single and multicore assembly

- XLETFE Family - Part 002: General
Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen zur allgemeines
Verwendung - XLETFE Familie - Teil 002: Allgemeines

Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs -

Famille XLETFE - Partie 002 : Généralités
Ta slovenski standard je istoveten z: EN 4611-002:2018
ICS:
29.060.20 Kabli Cables
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
SIST EN 4611-002:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 4611-002:2018
---------------------- Page: 2 ----------------------
SIST EN 4611-002:2018
EN 4611-002
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2018
EUROPÄISCHE NORM
ICS 49.060 Supersedes EN 4611-002:2012
English Version
Aerospace series - Cables, electrical, for general purpose,
single and multicore assembly - XLETFE Family - Part 002:
General

Série aérospatiale - Câbles, électriques, d'usage Luft- und Raumfahrt - Ein- und mehradrige elektrische

général, mono et multiconducteurs - Famille XLETFE - Leitungen zur allgemeinen Verwendung - XLETFE-

Partie 002 : Généralités Familie - Teil 002: Allgemeines
This European Standard was approved by CEN on 20 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4611-002:2018 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4611-002:2018
EN 4611-002:2018 (E)
Contents Page

European foreword ...................................................................................................................................................... 3

1 Scope .................................................................................................................................................................... 4

2 Normative references .................................................................................................................................... 4

3 Terms, definitions, symbols and abbreviations ................................................................................... 4

4 List of product standards ............................................................................................................................. 5

5 Materials and construction ......................................................................................................................... 5

6 Identification and marking .......................................................................................................................... 6

7 Technical specification ................................................................................................................................. 6

---------------------- Page: 4 ----------------------
SIST EN 4611-002:2018
EN 4611-002:2018 (E)
European foreword

This document (EN 4611-002:2018) has been prepared by the Aerospace and Defence Industries

Association of Europe - Standardization (ASD-STAN).

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has

received the approval of the National Associations and the Official Services of the member countries of

ASD, prior to its presentation to CEN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall

be withdrawn at the latest by February 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 4611-002:2012.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,

Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,

Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,

Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 4611-002:2018
EN 4611-002:2018 (E)
1 Scope
This European Standard speci
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.