SIST EN 15347:2024
(Main)Plastics - Recycled plastics - Characterisation of sorted plastics wastes
Plastics - Recycled plastics - Characterisation of sorted plastics wastes
This document provides a scheme for the characterisation of sorted plastics wastes, laying out those properties for which the supplier of the waste shall make information available to the purchaser, and appropriate test methods where applicable. The scheme provides for a division of information between "Required characteristics", where a statement is required and additional "Optional characteristics" which the supplier should provide based on the contractual agreements.
This document is applicable without prejudice to any existing legislation.
NOTE This document does not cover the characterisation of plastics recyclates.
Kunststoffe - Kunststoff-Rezyklate - Charakterisierung von sortierten Kunststoffabfällen
Dieses Dokument liefert ein Schema für die Charakterisierung von sortierten Kunststoffabfällen, wonach jene Eigenschaften umrissen werden, für die der Lieferant des Abfalls dem Käufer Informationen zugänglich machen und, falls anwendbar, angemessene Prüfverfahren angeben muss. Das Schema beinhaltet die Unterscheidung von Informationen in "geforderte Eigenschaften", deren Angabe erforderlich ist, und "optionale Eigenschaften", die der Lieferant auf Grundlage der vertraglichen Vereinbarungen angeben sollte.
Dieses Dokument beeinträchtigt bei seiner Anwendung keinerlei geltende Vorschriften.
ANMERKUNG Dieses Dokument befasst sich nicht mit der Charakterisierung von Kunststoff-Rezyklaten.
Plastiques - Plastiques recyclés - Caractérisation des déchets de plastiques triés
Le présent document donne un cadre relatif la caractérisation des déchets de plastiques triés, présentant des propriétés pour lesquelles le fournisseur de ces déchets doit mettre des informations à la disposition de l’acheteur, et le cas échéant, des méthodes d’essai appropriées. Le cadre scinde les informations en « Caractéristiques requises », pour lesquelles une déclaration est demandée, et en « Caractéristiques optionnelles » supplémentaires qu’il est recommandé au fournisseur de fournir sur la base des accords contractuels.
Le présent document est applicable sans préjudice de toute réglementation existante.
NOTE Le présent document ne couvre pas la caractérisation des recyclats de plastiques.
Polimerni materiali - Reciklirani polimerni materiali - Karakterizacija odpadkov sortiranih polimernih materialov
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 15347:2022
01-maj-2022
Polimerni materiali - Reciklirani polimerni materiali - Karakterizacija odpadkov
sortiranih polimernih materialov
Plastics - Recycled plastics - Characterisation of sorted plastics wastes
Kunststoffe - Kunststoff-Rezyklate - Charakterisierung von sortierten Kunststoffabfällen
Plastiques - Plastiques recyclés - Caractérisation des déchets de plastiques triés
Ta slovenski standard je istoveten z: prEN 15347
ICS:
13.030.50 Recikliranje Recycling
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN 15347:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 15347:2022
oSIST prEN 15347:2022
DRAFT
EUROPEAN STANDARD
prEN 15347
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2022
ICS 13.030.50; 83.080.01 Will supersede EN 15347:2007
English Version
Plastics - Recycled plastics - Characterisation of sorted
plastics wastes
Plastiques - Plastiques recyclés - Caractérisation des Kunststoffe - Kunststoff-Rezyklate - Charakterisierung
déchets de plastiques triés von sortierten Kunststoffabfällen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15347:2022 E
worldwide for CEN national Members.
oSIST prEN 15347:2022
prEN 15347:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviated terms . 5
4 Requirements . 5
4.1 General . 5
4.2 Classification scheme . 5
5 Quality assurance . 7
Bibliography . 8
oSIST prEN 15347:2022
prEN 15347:2022 (E)
European foreword
This document (prEN 15347:2022) has been prepared by Technical Committee CEN/TC 249 “Plastics”,
the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 15347:2007.
This document includes the following significant changes with respect to EN 15347:2007:
— Title was clarified, “sorted” has been added;
— Normative references have been updated;
— Table 1 “Required characteristics of sorted plastic waste” and Table 2 “Optional characteristics of
sorted plastic wastes” have been completely revised;
— Clause 5 “Quality assurance” has been revised;
— Bibliography has been updated.
This document is one part of a series of CEN publications on Plastics Recycling, which is structured as
follows:
— EN 15342, Plastics — Recycled Plastics — Characterization of polystyrene (PS) recyclates
— EN 15343, Plastics — Recycled Plastics — Plastics recycling traceability and assessment of conformity
and recycled content
— EN 15344, Plastics — Recycled Plastics — Characterization of Polyethylene (PE) recyclates
— EN 15345, Plastics — Recycled Plastics — Characterization of Polypropylene (PP) recyclates
— EN 15346, Plastics — Recycled plastics — Characterization of poly(vinyl chloride) (PVC) recyclates
— EN 15347, Plastics — Recycled Plastics — Characterization of sorted plastics wastes
— EN 15348, Plastics — Recycled plastics — Characterization of poly(ethylene terephthalate) (PET)
recyclates
— CEN/TR 15353, Plastics — Recycled plastics — Guidelines for the development of standards for
recycled plastics
oSIST prEN 15347:2022
prEN 15347:2022 (E)
Introduction
Recycling of plastics waste is one type of material recovery process intended to save resources (virgin
materials, water and energy), while minimizing harmful emissions into air, water and soil as well as any
impacts on human health. In order to be meaningful, the environmental impact of recycling should be
assessed over the whole life cycle of the recycling system (from the waste generation point to the disposal
of final residues). To ensure that recycling constitutes the best environmental option for treating the
available waste, some prerequisites should preferably be met:
— recycling scheme being contemplated should generate lower environmental impacts than alternative
recovery options;
— existing or potential market outlets should be identified that will secure a sustainable industrial
recycling operation;
— collection and sorting schemes should be properly designed to deliver recyclable plastics waste
fractions fitting reasonably well with the available recycling technologies and with the (changing)
needs of the identified market outlets, preferably at minimum costs to society.
This document has been produced in accordance with the guidance produced by CEN on Environmental
Aspects and in accordance with CEN/TR 15353, Plastics — Recycled plastics — Guidelines for the
development of standards for recycled plastics.
NOTE CEN/TR 15353 considers the general environmental aspects which are specific to the recycling process.
It is often impossible to trace back each individual product at the end user stage and to check whether
the product has been used correctly through its life. Consequently products are out of industrial control
for a period of time. It is possible that during this period contamination with other materials may occur
that could affect the product's suitability for recycling into the intended application.
oSIST prEN 15347:2022
prEN 15347:2022 (E)
1 Scope
This document provides a scheme for the characterization of sorted plastics wastes, laying out those
properties for which the supplier of the waste shall make information available to the purchaser, and
appropriate test methods where applicable. The scheme provides for a division of information between
“Required characteristics”, where a statement is required and additional “Optional characteristics”
which the supplier should provide based on the contractual agreements.
This document is applicable without prejudice to any existing legislation.
NOTE This document does not cover the characterization of plastics recyclates.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
prEN 17615, Plastics — Environmental Aspects — Vocabulary
3 Terms, definitions and abbreviated terms
For the purposes of this
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.