SIST EN 61347-2-13:2014/A1:2017
(Amendment)Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13:2014/A1:2016)
Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13:2014/A1:2016)
This part of IEC 61347 specifies particular safety requirements for electronic controlgear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules.
Geräte für Lampen - Teil 2-13: Besondere Anforderungen an gleich- oder wechselstromversorgte elektronische Betriebsgeräte für LED-Module
Appareillages de lampes - Partie 2-13: Exigences particulières pour les appareillages électroniques alimentés en courant continu ou alternatif pour les modules de LED
Krmilne stikalne naprave za sijalke - 2-13. del: Posebne zahteve za enosmerno ali izmenično napajane elektronske krmilne stikalne naprave za module LED - Dopolnilo A1 (IEC 61347-2-13:2014/A1:2016)
General Information
Relations
Overview
EN 61347-2-13:2014/A1:2017 (equivalent to IEC 61347-2-13:2014/A1:2016) defines particular safety requirements for electronic lamp controlgear intended for use with LED modules. The standard covers controlgear supplied from d.c. supplies up to 250 V and a.c. supplies up to 1 000 V (50 Hz or 60 Hz) and also covers outputs where the output frequency may deviate from the supply frequency. This Part 2-13 is intended to be used in conjunction with the latest edition of IEC 61347-1.
Key topics and requirements
- Scope and applicability: Electronic controlgear for LED modules supplied from specified d.c./a.c. voltages; applies to separate (non-integral) controlgear as well as specific marking/information requirements.
- Mandatory marking and information: Controlgear must be clearly and durably marked per IEC 61347-1 requirements and, where applicable:
- For constant-voltage types: rated output power (P_rated) and rated output voltage (U_rated).
- For constant-current types: rated output power (P_rated) and rated output current (I_rated).
- Indication if the controlgear is suitable for LED modules only.
- Maximum working/output voltage (Clause 21): Amendment introduces Clause 21 to verify the maximum output voltage (U_out) under any load condition (normal and abnormal). Test procedure highlights:
- Supply controlgear at rated supply voltage and load with LED modules at maximum declared electrical parameters.
- Modify the load (add LEDs in series/parallel or use resistors where appropriate) to find the condition that produces the highest terminal voltage. Note: no-load often yields the highest voltage in many designs.
- Measure maximum output voltage between output terminals and between terminals and earth (unless primary-secondary insulation negates the need).
- Use with IEC 61347-1: The amendment removes dated references so Part 2-13 is used alongside the latest IEC 61347-1 edition.
Applications
EN 61347-2-13 is essential for:
- Manufacturers of electronic controlgear for LED lighting (drivers, LED power supplies).
- Product safety and compliance engineers preparing technical files for CE marking.
- Test laboratories performing electrical safety and output-voltage verification (U_out) tests.
- Lighting system designers and specifiers ensuring safe compatibility between drivers and LED modules.
Related standards
- IEC 61347-1 (undated) - general requirements for lamp controlgear (to be used together with Part 2-13).
- EN 61347-2-13:2014/A1:2017 is the CENELEC-endorsed version of IEC 61347-2-13:2014/A1:2016.
Keywords: EN 61347-2-13, IEC 61347-2-13, lamp controlgear, electronic controlgear for LED modules, maximum output voltage, U_out, LED driver safety, constant-current, constant-voltage.
Frequently Asked Questions
SIST EN 61347-2-13:2014/A1:2017 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13:2014/A1:2016)". This standard covers: This part of IEC 61347 specifies particular safety requirements for electronic controlgear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules.
This part of IEC 61347 specifies particular safety requirements for electronic controlgear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules.
SIST EN 61347-2-13:2014/A1:2017 is classified under the following ICS (International Classification for Standards) categories: 29.130.01 - Switchgear and controlgear in general; 29.140.99 - Other standards related to lamps. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 61347-2-13:2014/A1:2017 has the following relationships with other standards: It is inter standard links to SIST EN IEC 61347-2-13:2025, SIST EN 61347-2-13:2014, SIST EN 61347-2-13:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 61347-2-13:2014/A1:2017 is associated with the following European legislation: EU Directives/Regulations: 2006/95/EC, 2014/35/EU; Standardization Mandates: M/511. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 61347-2-13:2014/A1:2017 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2017
.UPLOQHVWLNDOQHQDSUDYH]DVLMDONHGHO 3RVHEQH]DKWHYH]DHQRVPHUQRDOL
L]PHQLþQRQDSDMDQHHOHNWURQVNHNUPLOQHVWLNDOQHQDSUDYH]DPRGXOH/('
'RSROQLOR$ ,(& $
Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic
controlgear for LED modules (IEC 61347-2-13:2014/A1:2016)
Ta slovenski standard je istoveten z: EN 61347-2-13:2014/A1:2017
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 61347-2-13:2014/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2017
ICS 29.140.99
English Version
Lamp controlgear - Part 2-13: Particular requirements for d.c. or
a.c. supplied electronic controlgear for LED modules
(IEC 61347-2-13:2014/A1:2016)
Appareillages de lampes - Partie 2-13: Exigences Geräte für Lampen - Teil 2-13: Besondere Anforderungen
particulières pour les appareillages électroniques alimentés an gleich- oder wechselstromversorgte elektronische
en courant continu ou alternatif pour les modules de LED Betriebsgeräte für LED-Module
(IEC 61347-2-13:2014/A1:2016) (IEC 61347-2-13:2014/A1:2016)
This amendment A1 modifies the European Standard EN 61347-2-13:2014; it was approved by CENELEC on 2016-08-24. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61347-2-13:2014/A1:2017 E
European foreword
The text of document 34C/1199/FDIS, future IEC 61347-2-13:2014/A1, prepared by SC 34C
"Auxiliaries for lamps", of IEC/TC 34 "Lamps and related equipment" was submitted to the IEC-
CENELEC parallel vote and approved by CENELEC as EN 61347-2-13:2014/A1:2017.
The following dates are fixed:
(dop) 2017-10-28
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
(dow) 2020-04-28
• latest date by which the national standards conflicting with
the document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association.
Endorsement notice
The text of the International Standard IEC 61347-2-13:2014/A1:2016 was approved by CENELEC as
a European Standard without any modification.
IEC 61347-2-13 ®
Edition 2.0 2016-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AM ENDMENT 1
AM ENDEMENT 1
Lamp controlgear –
Part 2-13: Particular requirements for d.c. or a.c. supplied electron
...
SIST EN 61347-2-13:2014/A1:2017は、LEDモジュールのための電子制御機器に関する特定の安全要求事項を規定しています。この標準は、250 Vまでの直流電源および1,000 Vまでの交流電源（50 Hzまたは60 Hz）における電子制御機器の利用を対象としています。このような範囲は、特にLED技術の普及とともに重要性が増しています。 この標準の強みは、安全性に関する詳細なガイドラインを提供している点です。特に、高電圧を扱う場合において、その安全基準が明確に定義されており、製品を使用する際のリスクを最小限に抑えることができます。また、出力周波数が供給周波数から逸脱する場合の要件についても言及されており、柔軟性と適応性の高さが示されています。 SIST EN 61347-2-13:2014/A1:2017は、LED煌環技術に依存する現代の照明環境において、その適用性が非常に高いです。LEDモジュールの制御機器に対して信頼性のある基準を設定することで、製造業者や設計者が製品の安全性と性能を確保するための重要な指針となります。安全標準に準拠することは、ユーザーの信頼を高め、市場競争力を向上させる要素にもつながります。 このように、SIST EN 61347-2-13:2014/A1:2017は、LED技術が進化し続ける中で、その安全性と実用性を確保するための貴重なリソースとなっています。
The SIST EN 61347-2-13:2014/A1:2017 standard provides a comprehensive framework for the safety and functionality of electronic controlgear specifically designed for LED modules. Its scope is clearly defined, addressing both d.c. supplies up to 250 V and a.c. supplies up to 1,000 V at either 50 Hz or 60 Hz frequencies. This specification ensures a wide applicability of the controlgear across various scenarios while accommodating output frequencies that may deviate from the input supply frequency. One of the significant strengths of this standard lies in its focus on safety requirements. By setting forth particular safety guidelines tailored for electronic controlgear, SIST EN 61347-2-13 ensures that manufacturers adhere to optimal safety protocols, which is essential when dealing with LED technology that may be exposed to diverse voltage and frequency conditions. This commitment to safety not only protects end-users but also enhances the product integrity and reliability. Moreover, the standard's relevance is amplified in the context of the growing adoption of LED technology worldwide. As LED lighting becomes increasingly prevalent in both commercial and residential applications, having a standardized reference for the electronic controlgear helps maintain compatibility and performance across different devices and manufacturers. The clear specifications outlined within this document facilitate better design practices and operational standards, contributing to more efficient energy consumption and enhanced product performance. Overall, the SIST EN 61347-2-13:2014/A1:2017 standard plays a critical role in leading the industry towards safer, reliable, and more effective electronic controlgear solutions for LED modules, reinforcing its importance in contemporary lighting technologies.
La norme SIST EN 61347-2-13:2014/A1:2017 établit des exigences particulières de sécurité pour le matériel de contrôle électronique utilisé avec des alimentations en courant continu (d.c.) jusqu'à 250 V et en courant alternatif (a.c.) jusqu'à 1 000 V à des fréquences de 50 Hz ou 60 Hz. Ce document est particulièrement pertinent dans le contexte de l'essor des modules LED, qui sont de plus en plus utilisés dans divers secteurs, allant de l'éclairage domestique à l'éclairage public et industriel. Parmi les points forts de cette norme, on peut souligner la clarté et la précision des exigences de sécurité, qui sont essentielles pour assurer la fiabilité et la sécurité des systèmes d'éclairage modernes. La norme aborde également les variations possibles de fréquence en sortie, ce qui est crucial pour les applications LED, garantissant une compatibilité avec différentes configurations de réseau. En outre, la SIST EN 61347-2-13 inclut des recommandations sur la conception des circuits, la protection contre les surcharges et les court-circuits, et propose des essais spécifiques pour vérifier la conformité des dispositifs. Cela renforce sa pertinence dans le développement de nouveaux équipements d'éclairage, permettant aux fabricants de répondre aux attentes de sécurité élevées tout en favorisant l'innovation technique dans le secteur. Enfin, la norme joue un rôle crucial dans l'harmonisation internationale des exigences de sécurité, facilitant ainsi le commerce et l'évaluation des produits à l'échelle mondiale. En intégrant les spécificités du matériel de contrôle électronique destiné aux modules LED, elle contribue à la normalisation de pratiques sûres et efficaces, tout en soutenant la transition vers des solutions d'éclairage plus durables. Dans l'ensemble, la SIST EN 61347-2-13:2014/A1:2017 se positionne comme un document de référence indispensable pour toutes les parties prenantes impliquées dans la conception, la fabrication et l'utilisation de matériels de contrôle pour l'éclairage LED.
SIST EN 61347-2-13:2014/A1:2017 표준은 전자 제어 장치에 대한 특정 요구 사항을 규정하고 있으며, LED 모듈을 위한 직류 및 교류 공급 장치에서의 안전성을 보장하는 데 중요한 역할을 합니다. 이 표준은 직류 공급 장치 최대 250V 및 50Hz 또는 60Hz에서 최대 1,000V의 교류 공급 장치에 적용됩니다. 이 문서는 LED 조명 기술의 발전에 발맞추어 설계되었으며, LED 모듈 전자 제어 장치의 안전성 및 성능을 보장합니다. 본 표준은 특히 전도성 물질에 대한 내성과 방전 방식에서의 안전한 설계를 포함하여, 다양한 전기적 조건 하에서도 안정적으로 작동할 수 있도록 요구 사항을 설정합니다. SIST EN 61347-2-13:2014/A1:2017의 강점은 전자 제어 장치의 신뢰성을 높이고, LED 조명 시스템의 효율성을 극대화하는 데 기여하는 것입니다. 이 표준은 제조업체가 시장에서 요구되는 기준을 준수하도록 도와주며, 사용자에게는 안전하고 효율적인 조명 솔루션을 제공합니다. 또한, 이 표준은 LED 모듈 공급망의 일관성을 확보하여, 전 세계적으로 통합된 접근 방식을 지향합니다. 특히 전자 제어 장치가 포함된 LED 조명 시스템의 설계 및 제조에 있어 필수적인 지침을 제공하여, 관련 업계에서의 경쟁력을 강화하는 데 기여합니다. SIST EN 61347-2-13:2014/A1:2017은 현대 조명 기술의 요구를 충족시키기 위한 필수적인 가이드라인으로서, 안전 및 성능을 보장하는 데 있어 절대적인 기본 기준으로 자리 잡고 있습니다.
Die Norm SIST EN 61347-2-13:2014/A1:2017 stellt eine wichtige Grundlage für die Sicherheit von elektronischen Vorschaltgeräten dar, die für den Betrieb von LED-Modulen entwickelt wurden. Der Geltungsbereich dieser Norm umfasst spezifische Sicherheitsanforderungen für elektronische Steuergeräte, die sowohl mit Gleichstrom- als auch mit Wechselstromversorgungen eingesetzt werden können. Dies schließt Spannungen bis zu 250 V für Gleichstrom und bis zu 1.000 V für Wechselstrom bei 50 Hz oder 60 Hz ein. Ein herausragendes Merkmal dieser Norm ist die Berücksichtigung unterschiedlicher Betriebsspannungen und Frequenzen, was die Anwendung in einer Vielzahl von Beleuchtungssystemen ermöglicht. Die Norm beleuchtet die spezifischen Anforderungen, die für die Sicherheit im Zusammenhang mit LED-Technologien erforderlich sind, und berücksichtigt dabei sowohl die Sicherheit während des Betriebs als auch während der Installation. Ein weiterer Vorteil der SIST EN 61347-2-13:2014/A1:2017 ist ihre Relevanz in der schnell wachsenden LED-Branche, wo der Einsatz von elektronischen Steuergeräten für die Effizienz und Langlebigkeit von Beleuchtungssystemen von zentraler Bedeutung ist. Die Norm schafft Vertrauen bei Herstellern und Endverbrauchern, indem sie sicherstellt, dass die Produkte nicht nur leistungsfähig, sondern auch sicher sind. Die Integration dieser spezifischen Anforderungen in die Norm geht zudem auf aktuelle Entwicklungen und Innovationen in der LED-Technologie ein. Dies stellt sicher, dass die Norm stets den neuesten technischen Standards entspricht und somit eine moderne und zukunftssichere Lösung für die Lichttechnik bietet. Damit bleibt die SIST EN 61347-2-13:2014/A1:2017 ein essentielles Instrument für Hersteller und Planer, die qualitative und sichere Beleuchtungssysteme entwickeln möchten.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...