Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). Part 1 of this International Standard deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.

Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 2: Langfaserverstärkte Kunststoffe (ISO 10350-2:2011)

ISO 10350 legt spezifische Prüfverfahren zur Ermittlung und Darstellung vergleichbarer Kennwerte für
bestimmte grundlegende Eigenschaften von Kunststoffen fest. Im Allgemeinen wird jede Eigenschaft durch
einen einzelnen Messwert festgelegt, in bestimmten Fällen wird eine Eigenschaft jedoch durch zwei Werte
charakterisiert, die unter verschiedenen Prüfbedingungen oder entlang unterschiedlicher Materialrichtungen
ermittelt wurden. Die aufgeführten Eigenschaften werden vom Hersteller üblicherweise in Datenblättern
erfasst. Dieser Teil der ISO 10350 gilt für thermoplastische und duroplastische Werkstoffe, die eine
Verstärkung entweder durch diskontinuierliche Fasern mit einer Länge vor der Verarbeitung von mehr als
7,5 mm oder durch kontinuierliche Fasern haben (z. B. Gewebe, kontinuierliche Matten aus Einzellitzen oder
unidirektionale Kunststoffe). Teil 1 dieser Internationalen Norm behandelt speziell unverstärkte und gefüllte
Kunststoffe sowie Kunststoffe mit Fasern, deren Länge weniger als 7,5 mm beträgt.

Plastiques - Acquisition et présentation de caractéristiques intrinseques comparables - Partie 2: Plastiques renforcés par de longues fibres (ISO 10350-2:2011)

L'ISO 10350 identifie des méthodes d'essai spécifiques en vue de l'acquisition et de la présentation de données comparables relatives à certaines propriétés de base des matières plastiques. En général, chaque propriété est spécifiée par une valeur expérimentale unique; toutefois, dans certains cas, certaines propriétés sont représentées par deux valeurs obtenues dans des conditions d'essai différentes ou dans différentes directions du matériau. Les propriétés indiquées sont celles qui sont traditionnellement présentées dans les fiches techniques des fabricants. L'ISO 10350-2:2011 est applicable aux matériaux thermodurcissables ou thermoplastiques renforcés, dont les fibres de renforcement sont soit discontinues et d'une longueur supérieure à 7,5 mm avant la mise en oeuvre, soit continues (tissu, mat de fils de base continus ou unidirectionnels, par exemple). L'ISO 10350‑1 traite spécifiquement des plastiques non renforcés et comportant des charges, y compris ceux qui comportent des fibres de moins de 7,5 mm de longueur.

Polimerni materiali - Pridobitev in predstavitev primerljivih značilnih enotočkovnih podatkov - 2. del: Z dolgimi vlakni ojačeni polimerni materiali (ISO 10350-2:2011)

ISO 10350 identificira specifične preskusne postopke za pridobitev in predstavitev primerljivih podatkov za določene osnovne lastnosti polimernih materialov. Na splošno je vsaka lastnost določena z eno eksperimentalno vrednostjo, v nekaterih primerih pa lastnosti predstavljata dve vrednosti, dobljeni pri različnih preskusnih pogojih ali vzdolž različnih smeri v materialu. Vključene so tiste lastnosti, ki so običajno predstavljene v tehničnih podatkih proizvajalcev. Ta del ISO 10350 velja za ojačane termoreaktivne in plastomerne materiale, pri katerih so ojačitvena vlakna diskontinuirna, z dolžino vlaken pred obdelavo nad 7,5 mm, ali kontinuirna (npr. mat blago s kontinuirnimi niti ali enosmerni). 1. del tega mednarodnega standarda posebej obravnava neojačane in polnjene polimerne materiale, vključno z materiali, ki uporabljajo vlakna, krajša od 7,5 mm.

General Information

Status
Withdrawn
Publication Date
14-Sep-2011
Withdrawal Date
31-Aug-2020
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
27-Aug-2020
Due Date
19-Sep-2020
Completion Date
01-Sep-2020

Relations

Buy Standard

Standard
EN ISO 10350-2:2011
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10350-2:2011
01-oktober-2011
1DGRPHãþD
SIST EN ISO 10350-2:2002
3ROLPHUQLPDWHULDOL3ULGRELWHYLQSUHGVWDYLWHYSULPHUOMLYLK]QDþLOQLKHQRWRþNRYQLK
SRGDWNRYGHO=GROJLPLYODNQLRMDþHQLSROLPHUQLPDWHULDOL ,62
Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-
fibre-reinforced plastics (ISO 10350-2:2011)
Kunststoffe - Ermittlung und Darstellung vergleichbarer Einpunktkennwerte - Teil 2:
Langfaserverstärkte Kunststoffe (ISO 10350-2:2011)
Plastiques - Acquisition et présentation de caractéristiques intrinseques comparables -
Partie 2: Plastiques renforcés par de longues fibres (ISO 10350-2:2011)
Ta slovenski standard je istoveten z: EN ISO 10350-2:2011
ICS:
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN ISO 10350-2:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10350-2:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 10350-2:2011


EUROPEAN STANDARD
EN ISO 10350-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2011
ICS 83.120 Supersedes EN ISO 10350-2:2001
English Version
Plastics - Acquisition and presentation of comparable single-
point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-
2:2011)
Plastiques - Acquisition et présentation de caractéristiques Kunststoffe - Ermittlung und Darstellung vergleichbarer
intrinsèques comparables - Partie 2: Plastiques renforcés Einpunktkennwerte - Teil 2: Langfaserverstärkte
par de longues fibres (ISO 10350-2:2011) Kunststoffe (ISO 10350-2:2011)
This European Standard was approved by CEN on 3 March 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10350-2:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10350-2:2011
EN ISO 10350-2:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10350-2:2011
EN ISO 10350-2:2011 (E)
Foreword
This document (EN ISO 10350-2:2011) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2011, and conflicting national standards shall be
withdrawn at the latest by September 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10350-2:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10350-2:2011 has been approved by CEN as a EN ISO 10350-2:2011 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 10350-2:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 10350-2:2011

INTERNATIONAL ISO
STANDARD 10350-2
Second edition
2011-03-01


Plastics — Acquisition and presentation
of comparable single-point data —
Part 2:
Long-fibre-reinforced plastics
Plastiques — Acquisition et présentation de caractéristiques
intrinsèques comparables —
Partie 2: Plastiques renforcés par de longues fibres




Reference number
ISO 10350-2:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 10350-2:2011
ISO 10350-2:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10350-2:2011
ISO 10350-2:2011(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Specimen preparation and conditioning.3
5 Test requirements .4
6 Presentation of results.4
Bibliography.9

© ISO 2011 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10350-2:2011
ISO 10350-2:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10350-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 2, Mechanical
properties.
This second edition cancels and replaces the first edition (ISO 10350-2:2001), which has been technically
revised.
ISO 10350 consists of the following parts, under the general title Plastics — Acquisition and presentation of
comparable single-point data:
⎯ Part 1: Moulding materials
⎯ Part 2: Long-fibre-reinforced plastics

iv © ISO 2011 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 10350-2:2011
ISO 10350-2:2011(E)
Introduction
This part of ISO 10350 has been prepared because users of long-fibre-reinforced plastics find that available
data cannot always be readily used to compare the properties of similar materials, especially when the data
have been supplied by different sources. Even when the same standard tests have been used, they may allow
the adoption of a wide range of alternative test conditions, and the data obtained are not necessarily
comparable. The purpose of this part of ISO 10350 is to identify specific methods and conditions of test to be
used for the acquisition and presentation of data in order that valid comparisons between materials can be
made.
This part of ISO 10350 is concerned with tests employed to present “single-point” data on the limited range of
properties commonly included in data sheets and used for the preliminary selection of materials. Such data
represent the most basic approach to the specification of properties of materials and this part of ISO 10350
thus facilitates the first steps towards more efficient selection and use of plastics in the many applications to
which they are suited.
Many properties of long-fibre-reinforced plastics are anisotropic. The test method standards for these
properties have been produced with different procedures for specific types of reinforcement. In this part of
ISO 10350, use of the appropriate procedure is specified rather than the use of a specific specimen geometry
as adopted in Part 1 for moulding materials. This is necessary for the recording of meaningful material
property values.
Complementary International Standards (ISO 11403-1, ISO 11403-2 and ISO 11403-3) (see the Bibliography)
are concerned with the standardized acquisition and presentation of multipoint data, to demonstrate how
properties vary with important factors such as time, temperature and the presence of particular natural and
chemical environments. In these standards, some additional properties are included. Their use will provide a
more substantial database than one containing only single-point data, and so will enable improved
assessment of the fitness of a material for any particular application. In addition, ISO 11403-1, which deals
with mechanical properties, assists predictions of the performance of components and ISO 11403-2, covering
thermal and processing properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3
is concerned with environmental influences on properties, and other parts may be prepared to cover additional
properties. The various parts of ISO 11403 were written primarily for moulding materials. The test methods
and test conditions referred to might not therefore be ideally suited to the acquisition of data for all long-fibre-
reinforced plastics.


© ISO 2011 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 10350-2:2011

---------------------- Page: 12 ----------------------

SIST EN ISO 10350-2:2011
INTERNATIONAL STANDARD ISO 10350-2:2011(E)

Plastics — Acquisition and presentation of comparable single-
point data —
Part 2:
Long-fibre-reinforced plastics
1 Scope
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for
certain basic properties of plastics. In general, each property is specified by a single experimental value,
although in certain cases properties are represented by two values obtained under different test conditions or
along different directions in the material. The properties included are those presented conventionally in
manufacturers' data sheets. This part of ISO 10350 applies to reinforced thermoplastic and thermosetting
materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing
greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). Part 1 of this
International Standard deals specifically with unreinforced and filled plastics, including those using fibres less
than 7,5 mm in length.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-3, Plastics — Determination of temperature of deflection under load — Part 3: High-strength
thermosetting laminates and long-fibre-reinforced plastics
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 527-4, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and
orthotropic fibre-reinforced plastic composites
ISO 527-5, Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-
reinforced plastic composites
ISO 1172, Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination
of the textile-glass and mineral-filler content — Calcination methods
ISO 1183 (all parts), Plastics — Methods for determining the density of non-cellular plastics
ISO 1268 (all parts), Fibre-reinforced plastics — Methods of producing test plates
© ISO 2011 – All rights reserved 1

---------------------- Page: 13 ----------------------

SIST EN ISO 10350-2:2011
ISO 10350-2:2011(E)
ISO 2577, Plastics — Thermosetting mouldi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.