iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60068-2-69:2017/AC:2018

(Corrigendum)

Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method

Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method

IEC corrigendum

Umgebungseinflüsse - Teil 2-69: Prüfungen - Prüfung Te/TC: Prüfung der Lötbarkeit von Bauelementen der Elektronik und Leiterplatten mit der Benetzungswaage (Kraftmessung)

Essais d'environnement - Partie 2-69: Essais - Essai Te/Tc: Essai de brasabilité des composants électroniques et cartes imprimées par la méthode de la balance de mouillage (mesure de la force)

Okoljski preskusi - 2-69. del: Preskusi - Preskus Te/Tc: Preskus spajkanja elektronskih komponent in plošč tiskanih vezij z metodo za določanje omočljivosti (merjenje sile)

General Information

Status
Published
Publication Date
21-May-2018
ICS
19.040 - Environmental testing
31.190 - Electronic component assemblies
Technical Committee
ITIV - Electronics assembly technology and Environmental standardization
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
25-Apr-2018
Due Date
30-Jun-2018
Completion Date
22-May-2018
Ref Project
EN 60068-2-69:2017/AC:2018-03 - Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method

Relations

Corrects
SIST EN 60068-2-69:2017 - Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
Effective Date
06-Feb-2018

Buy Standard

EN 60068-2-69:2017/AC:2018EN 60068-2-69:2017/AC:2018
PreviousNext
Corrigendum
EN 60068-2-69:2017/AC:2018
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VSDMNDQMDUmgebungseinflüsse - Teil 2-69: Prüfungen - Prüfung Te/TC: Prüfung der Lötbarkeit von Bauelementen der Elektronik und Leiterplatten mit der Benetzungswaage (Kraftmessung)Essais d'environnement - Partie 2-69: Essais - Essai Te/Tc: Essai de brasabilité des composants électroniques et cartes imprimées par la méthode de la balance de mouillage (mesure de la force)Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method31.190Sestavljeni elektronski elementiElectronic component assemblies19.040Preskušanje v zvezi z okoljemEnvironmental testingICS:Ta slovenski standard je istoveten z:EN 60068-2-69:2017/AC:2018-03SIST EN 60068-2-69:2017/AC:2018en01-junij-2018SIST EN 60068-2-69:2017/AC:2018SLOVENSKI
STANDARD



SIST EN 60068-2-69:2017/AC:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 60068-2-69:2017/AC:2018-03
March 2018
ICS 19.040; 31.190 English Version
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method (IEC 60068-2-69:2017/COR1:2018)
Essais d'environnement - Partie 2-69: Essais - Essai Te/Tc: Essai de brasabilité des composants électroniques et cartes imprimées par la méthode de la balance de mouillage (mesure de la force) (IEC 60068-2-69:2017/COR1:2018)
Umgebungseinflüsse - Teil 2-69: Prüfungen - Prüfung Te/TC: Prüfung der Lötbarkeit von Bauelementen der Elektronik und Leiterplatten mit der Benetzungswaage (Kraftmessung) (IEC 60068-2-69:2017/COR1:2018) This corrigendum becomes effective on 9 March 2018 for incorporation in the English language version of the EN. European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung CEN-CENELEC Management Centre: Rue de la Science 23,
B-1040 Brussels © 2018 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60068-2-69:2017/AC:2018-03 ESIST EN 60068-2-69:2017/AC:2018



EN 60068-2-69:2017/AC:2018-03
Endorsement notice
The text of the corrigendum IEC 60068-2-69:2017/COR1:2018
was approved by CENELEC as EN 60068-2-69:2017/AC:2018-03 without any modification.
SIST EN 60068-2-69:2017/AC:2018



IEC 60068-2-69:2017/COR1:2018 – 1 –
 IEC 2018 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE ____________
IEC 60068-2-69 Edition 3.0
2017-03
ENVIRONMENTAL TESTING –
Part 1: 2-69: Tests – Test Te/Tc: Solderability testing of electronic components and
printed boards by the wetting balance
(force measurement) IEC 60068-2-69 Édition 3.0
2017-03
ESSAIS D'ENVIRONNEMENT –
Partie 2-69: Essais – Essai Te/Tc: Essai de brasabilité des composants électroniques et cartes imprimées par la méthode de la balance de
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60068-2-21:2021(Main)
Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices
EN IEC 60068-2-21:2021

This document specifies two separate methods for determining the resistance of a material to wet and
dry abrasion.
It is applicable to the coated surface or surfaces of coated fabrics.
It does not apply to determining the abrasion behaviour of an uncoated surface of a coated fabric, for
which the methods for uncoated textiles described in the ISO 12947 series apply.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-69:2017/A1:2021(Amendment)
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN 60068-2-69:2017/A1:2019
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60068-2-82:2019(Main)
Environmental testing - Part 2-82: Tests - Test Xw1: Whisker test methods for components and parts used in electronic assemblies
EN IEC 60068-2-82:2019

This part of IEC 60068 specifies tests for the whiskering propensity of surface finishes of
electric or electronic components and mechanical parts such as punched/stamped parts (for
example, jumpers, electrostatic discharge protection shields, mechanical fixations, press-fit
pins and other mechanical parts used in electronic assemblies) representing the finished
stage, with tin or tin-alloy finish. Changes of the physical dimensions of mould compounds,
plastics and the like during the required test flow are not considered or assessed. The test
methods have been developed by using a knowledge-based approach.
This document can also be used at sub-suppliers, like plating shops, stamping shops or other
service providers to ensure a consistent surface quality within the supply chain.
These test methods are employed with defined acceptance criteria by a relevant component
or application specification.
The tests described in this document are applicable for initial qualification, for periodic
monitoring in accordance with Clause 7, and for changes of technology or manufacturing
processes of existing surfaces in accordance with Clause 9.
The mating area of connectors is not covered by this test method. IEC 60512-16-21 applies
for the mating areas of connectors.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-58:2015/A1:2018(Amendment)
Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
EN 60068-2-58:2015/A1:2018
  • Amendment
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-69:2017(Main)
Environmental testing - Part 2-69: Tests - Test Te/Tc: Solderability testing of electronic components and printed boards by the wetting balance (force measurement) method
EN 60068-2-69:2017

This part of IEC 60068 outlines test Te/Tc, the solder bath wetting balance method and the
solder globule wetting balance method to determine, quantitatively, the solderability of the
terminations. Data obtained by these methods are not intended to be used as absolute
quantitative data for pass–fail purposes.
The procedures describe the solder bath wetting balance method and the solder globule
wetting balance method. They are applicable to components and printed boards with metallic
terminations and metallized solder pads.
This document provides the measurement procedures for solder alloys both with and without
lead (Pb).

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60068-2-58:2015(Main)
Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD)
EN 60068-2-58:2015

This part of IEC 60068 outlines test Td, applicable to surface mounting devices (SMD).
This standard provides procedures for determining the solderability and resistance to
soldering heat of devices in applications using solder alloys, which are eutectic or near
eutectic tin lead (Pb), or lead-free alloys.
The procedures use either a solder bath or reflow method and are applicable only to
specimens or products designed to withstand short term immersion in molten solder or limited
exposure to reflow systems.
The solder bath method is applicable to SMDs designed for flow soldering and SMDs
designed for reflow soldering when the solder bath (dipping) method is appropriate.
The reflow method is applicable to the SMD designed for reflow soldering, to determine the
suitability of SMDs for reflow soldering and when the solder bath (dipping) method is not
appropriate.
The objective of this standard is to ensure solderability of component lead or termination. In
addition, test methods are provided to ensure that the component body can resist against the
heat load to which it is exposed during soldering.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62137-3:2012(Main)
Electronics assembly technology - Part 3: Selection guidance of environmental and endurance test methods for solder joints
EN 62137-3:2012

IEC 62137-3:2011 describes the selection methodology of an appropriate test method for a reliability test for solder joints of various shapes and types of surface mount devices (SMD), array type devices and leaded devices, and lead insertion type devices using various types of solder material alloys. This first edition cancels and replaces IEC/PAS 62137-3, published in 2008, and includes some editorial revisions. The main changes with respect to the PAS include the following:
- no technical changes;
- some editorial changes and corrections;
- for the sake of convenience some constitutive changes.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62137-1-5:2010(Main)
Surface mounting technology - Environmental and endurance test methods for surface mount solder joints -- Part 1-5: Mechanical shear fatigue test
EN 62137-1-5:2009

The test method described in this part of IEC 62137 applies to area array packages, such as BGA. This test method is designed to evaluate the fatigue life of the solder joints between component leads and lands on a substrate as shown in Figure 1. A temperature cyclic approach is generally used to evaluate the reliability of solder joints. Another method is to mechanically cycle the solder joints to shorten the testing time rather than to produce the strains by changing temperatures. The methodology is the imposition of shear deformation on the solder joints by mechanical displacement instead of relative displacement generated by CTE (coefficient of thermal expansion) mismatch, as shown in Figure 2. In place of the temperature cycle test, the mechanical shear fatigue predicts the reliability of the solder joints under repeated temperature change conditions by mechanically cycling the solder joints. In this test method, the evaluation requires first to mount the surface mount component on the substrate by reflow soldering, then cyclic mechanical shear deformation is applied to the solder joints until fracture of the solder joints occurs. The properties of the solder joints (for example solder alloy, substrate, mounted device or design, etc.) are evaluated to assist in improving the strength of the solder joints.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62137-1-4:2009
Surface mounting technology - Environmental and endurance test methods for surface mount solder joint - Part 1-4: Cyclic bending test
EN 62137-1-4:2009

The test method described in this part of IEC 62137 applies to surface mount components with a thin and wide basal plane, such as QFP and BGA. This test method evaluates the endurance of the solder joints between component leads and lands on a substrate by cyclic bending of substrate. This test also evaluates the effects of repeated mechanical stress, such as key pushing in cell phones, the strength of the solder joint between component terminals and lands on a substrate. In this test method, the evaluation requires first to mount the surface mount component on the substrate by reflow soldering, then cyclically bend the substrate to a certain degree of depth until fracture of the solder joints occurs. The properties of the solder joints (e.g, solder alloy, substrate, mounted device or design, etc.) are evaluated to assist in improving the strength of the solder joints.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62137-1-3:2009
Surface mounting technology - Environmental and endurance test methods for surface mount solder joint -- Part 1-3: Cyclic drop test
EN 62137-1-3:2009

The test method described in this part of IEC 62137 applies to solder joints between terminals of surface mounting devices (SMDs) and land patterns on printed wiring boards (PWBs). This test is intended to evaluate the strength of the solder joints of larger sized multi-terminal components and other components in devices (e.g. handheld mobile devices) in the event that the device is dropped. The properties of the solder joints (e.g. solder alloy, substrate, mounted device or design, etc.) are evaluated to assist in improving the strength of the solder joints.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day