Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame retarded, fluid resistant, shrink ratio 2:1

Gives the requirements for one type of heat-shrinkable, flame retarded, with a nominal shrink ratio 2:1, fluid resistant polyvinylidene fluoride sleeving for use at temperatures up to 175 C. This sleeving is normally supplied with an internal diameter up to 25,4 mm, and the standard colour is transparent. Sizes or colours other than those specifically listed in this standard may be available as custom items. These items are considered to comply with this standard if they comply with the property requirements listed in Tables 2, 3, 4 and 5, with the exception of dimensions and mass. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. This edition includes the following significant technical change with regard to the previous edition: Replacement of the thermal endurance test method according to EN 60216 with a long term ageing test, i.e. 3 000 h at the recommended maximum temperature found suitable for use,in order to provide safe thermal test data within a workable time scale.

Isolierschläuche -- Teil 3: Anforderungen für einzelne Schlauchtypen -- Blatt 228: Wärmeschrumpfende Polyvinylidenefluoridschläuche, halbsteif, flammwidrig, flüssigkeitsbeständig, Schrumpfverhältnis 2:1

Gaines isolantes souples -- Partie 3: Spécifications pour types particuliers de gaines -- Feuille 228: Gaines thermorétractables semi-rigides en fluorure de polyvinylidène, retardées à la flamme, résistant aux fluides, rapport de rétreint 2:1

Donne les exigences relatives à un type de gaines thermorétractables en fluorure de polyvinylidène, retardées à la flamme de rapport de rétreint nominal 2:1 et résistant aux fluides, pour un usage allant jusqu'à une température de 175 °C. Cette gaine est normalement fournie avec un diamètre intérieur allant jusqu'à 25,4 mm et la couleur standard est transparente. D'autres dimensions et d'autres couleurs que celles spécifiquement indiquées dans cette norme peuvent être disponibles, comme articles spéciaux. Ces articles sont considérés comme satisfaisant à cette norme s'ils correspondent aux caractéristiques indiquées dans les Tableaux 2, 3, 4 et 5, en excluant les dimensions et la masse. Les matériaux conformes à la présente spécification satisfont aux niveaux de performance établis. Cependant il convient que le choix d'un matériau, par un utilisateur, pour une application spécifique, soit fondé sur les exigences réelles nécessaires pour obtenir les performances satisfaisantes pour cette application, et qu'il ne soit pas fondé sur cette seule spécification. Cette édition comprend la modification technique majeure suivante par rapport à l'édition précédente: Remplacement de la méthode d'essai d'endurance thermique conformément à la EN 60216 par un essai de vieillissement à long terme, c'est-à-dire 3 000 h, à la température maximale recommandée pour un usage adapté, afin de fournir des données d'essai thermiques comprises dans une échelle de temps exploitable.

Gibke izolacijske cevi – 3. del: Specifikacija za posamezne vrste cevi – 228. list: Toplotno skrčljive poltoge poliviniliden-fluoridne cevi, ognjevarne, odporne proti tekočinam, razmerje krčenja 2:1 (IEC 60684-3-228:1998)

General Information

Status
Published
Publication Date
31-Dec-2004
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jan-2005
Due Date
01-Jan-2005
Completion Date
01-Jan-2005

RELATIONS

Buy Standard

Standard
SIST EN 60684-3-228:2005
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI SIST EN 60684-3-228:2005
STANDARD
januar 2005
Gibke izolacijske cevi – 3. del: Specifikacija za posamezne vrste cevi – 228.
list: Toplotno skrčljive poltoge poliviniliden-fluoridne cevi, ognjevarne,
odporne proti tekočinam, razmerje krčenja 2:1 (IEC 60684-3-228:1998)
(istoveten EN 60684-3-228:2004)

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving -

Sheet 228: Heat- shrinkable, semi-rigid polyvinylidene fluoride sleeving, flame
retarded, fluid resistant, shrink ratio 2:1 (IEC 60684-3-228:1998)
ICS 29.035.20 Referenčna številka
SIST EN 60684-3-228:2005(en)

© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 60684-3-228
NORME EUROPÉENNE
EUROPÄISCHE NORM August 2004
ICS 29.035.20 Supersedes EN 60684-3-228:1998
English version
Flexible insulating sleeving
Part 3: Specifications for individual types of sleeving
Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving,
flame retarded, fluid resistant, shrink ratio 2:1
(IEC 60684-3-228:2004)
Gaines isolantes souples Isolierschläuche
Partie 3: Spécifications pour types Teil 3: Anforderungen für einzelne
particuliers de gaines Schlauchtypen
Feuille 228: Gaines thermorétractables Blatt 228: Wärmeschrumpfende

semi-rigides en fluorure de polyvinylidène, Polyvinylidenefluoridschläuche, halbsteif,

retardées à la flamme, résistant flammwidrig, flüssigkeitsbeständig,
aux fluides, rapport de rétreint 2:1 Schrumpfverhältnis 2:1
(CEI 60684-3-228:2004) (IEC 60684-3-228:2004)

This European Standard was approved by CENELEC on 2004-07-01. CENELEC members are bound to

comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on

application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CENELEC member into its own language and

notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech

Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,

Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60684-3-228:2004 E
---------------------- Page: 2 ----------------------
EN 60684-3-228:2004 - 2 -
Foreword

The text of document 15C/1599/FDIS, future edition 2 of IEC 60684-3-228, prepared by SC 15C,

Specifications, of IEC TC 15, Insulating materials, was submitted to the IEC-CENELEC parallel vote

and was approved by CENELEC as EN 60684-3-228 on 2004-07-01.
This European Standard supersedes EN 60684-3-228:1998.
The significant technical change with regard to EN 60684-2-228:1998 is:

- Replacement of the thermal endurance test method according to EN 60216 with a long term ageing

test, i.e. 3 000 h at the recommended maximum temperature found suitable for use, in order to

provide safe thermal test data within a workable time scale.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-07-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice

The text of the International Standard IEC 60684-3-228:2004 was approved by CENELEC as a

European Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 60684-3-228:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced

document (including any amendments) applies.

NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant

EN/HD applies.
Publication Year Title EN/HD Year
IEC 60684-1 2003 Flexible insulating sleeving EN 60684-1 2003
Part 1: Definitions and general
requirements
IEC 60684-2 1997 Part 2: Methods of test EN 60684-2 1997
A1 2003 A1 2003
IEC 60757 1983 Code for designation of colours HD 457 S1 1985
ISO 846 1997 Plastics - Evaluation of the action of EN ISO 846 1997
micro-organisms
ISO 1817 1999 Rubber, vulcanized - Determination of the - -
effect of liquids
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE
IEC
60684-3-228
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2004-05
Gaines isolantes souples –
Partie 3:
Spécifications pour types particuliers de gaines –
Feuille 228: Gaines thermorétractables semi-
rigides en fluorure de polyvinylidène,
retardées à la flamme, résistant aux fluides,
rapport de rétreint 2:1
Flexible insulating sleeving –
Part 3:
Specifications for individual types of sleeving –
Sheet 228: Heat-shrinkable, semi-rigid
polyvinylidene fluoride sleeving,
flame retarded, fluid resistant, shrink ratio 2:1
 IEC 2004 Droits de reproduction réservés  Copyright - all rights reserved

Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any

utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including

électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from

microfilms, sans l'accord écrit de l'éditeur. the publisher.

International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland

Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch

CODE PRIX
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 5 ----------------------
60684-3-228  IEC:2004 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
FLEXIBLE INSULATING SLEEVING –
Part 3: Specifications for individual types of sleeving –
Sheet 228: Heat-shrinkable, semi-rigid polyvinylidene fluoride sleeving,
flame retarded, fluid resistant, shrink ratio 2:1
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any

equipment declared to be in conformity with an IEC Publication.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60684-3-228 has been prepared by subcommittee 15C:
Specificatio
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.