SIST EN 60684-3-211:2007

Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1

This part of IEC 60684 gives the requirements for four types of semi-rigid, heat-shrinkable polyolefin sleeving with a nominal shrink ratio of 2:1 that has been found suitable for temperatures up to 135 °C. - Type A: general purpose, flame-retarded, opaque colours; - Type B: general purpose, non flame-retarded, translucent; - Type C: fluid resistant, flame-retarded, opaque colours; - Type D: fluid resistant, non flame-retarded, translucent. The sleeving is normally available in internal diameter sizes up to 12,7 mm as supplied, in the following colours: black, white, red, yellow, blue and translucent. Sizes or colours other than those specifically listed in this standard may be available as custom items. The items are considered to comply with this standard if they comply with the property requirements listed in tables 2, 3 and also with the property requirements of Table 4 for types C and D, excluding dimensions. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone.

Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 211: Wärmeschrumpfschläuche, halbfestes Polyolefin, Schrumpfverhältnis 2:1

Gaines isolantes souples -- Partie 3: Spécifications pour types particuliers de gaines -- Feuille 211: Gaines thermorétractables, en polyoléfine, semi-rigides, à rapport de rétreint 2:1

Donne les exigences relatives aux gaines semi-rigides, thermorétractables, en polyoléfine, ayant un rapport de rétreint nominal de 2:1 et que l'on considère comme adaptées jusqu'à une température de 135°C. Type 1: Tous usages, retardées à la flamme, couleurs opaques. Type 2: Tous usages, non retardées à la flamme, translucides. Type 3: Résistant aux fluides, retardées à la flamme, couleurs opaques. Type 4: Résistant aux fluides, non retardées à la flamme, translucides. D'autres dimensions et d'autres couleurs que celles spécifiquement indiquées dans cette norme peuvent être disponibles comme articles spéciaux. Ces articles doivent être considérés comme satisfaisant à cette norme s'ils satisfont aux autres caractéristiques indiquées dans les tableaux 2, 3 et dans la colonne des exigences du tableau 4 pour les types 3 et 4 à l'exception des dimensions. Les matériaux conformes à cette spécification satisfont à des niveaux établis de performance. Cependant il convient que le choix d'un matériau par un utilisateur pour une application spécifique soit fondé sur les exigences réelles nécessaires pour une performance adéquate de cette application, et non fondé sur cette seule spécification.

Gibke izolacijske cevi - 3. del: Specifikacije za posamezne tipe cevi - 211. list: Toplotno skrčljive poltoge poliolefinske cevi, razmerje krčenja 2:1 (IEC 60684-3-211:2007)

General Information

• Status: Published
• Publication Date: 30-Sep-2007
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: IZO - Insulating materials
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 17-Sep-2007
• Due Date: 22-Nov-2007
• Completion Date: 01-Oct-2007
• Ref Project: EN 60684-3-211:2007 - Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving - Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1

Relations

• Replaces: SIST EN 60684-3-211:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60684-3-211:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1
• Effective Date: 13-May-2010
• Replaces: SIST EN 60684-3-211:2004 - Flexible insulating sleeving -- Part 3: Specifications for individual types of sleeving -- Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60684-3-211:2007
01-november-2007
1DGRPHãþD
SIST EN 60684-3-211:2004
*LENHL]RODFLMVNHFHYLGHO6SHFLILNDFLMH]DSRVDPH]QHWLSHFHYLOLVW
7RSORWQRVNUþOMLYHSROWRJHSROLROHILQVNHFHYLUD]PHUMHNUþHQMD,(&

Flexible insulating sleeving - Part 3: Specifications for individual types of sleeving --
Sheet 211: Heat-shrinkable sleeving, semi-rigid polyolefin, shrink ratio 2:1 (IEC 60684-3-
211:2007)
Isolierschläuche - Teil 3: Anforderungen für einzelne Schlauchtypen - Blatt 211:
Wärmeschrumpfschläuche, halbfestes Polyolefin, Schrumpfverhältnis 2:1 (IEC 60684-3-
211:2007)
Gaines isolantes souples - Partie 3: Spécifications pour types particuliers de gaines --
Feuille 211: Gaines thermorétractables, en polyoléfine, semi-rigides, a rapport de rétreint
2:1 (IEC 60684-3-211:2007)
Ta slovenski standard je istoveten z: EN 60684-3-211:2007
ICS:
29.035.20 3ODVWLþQLLQJXPHQLL]RODFLMVNL Plastics and rubber insulating
PDWHULDOL materials
SIST EN 60684-3-211:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 60684-3-211

NORME EUROPÉENNE
May 2007
EUROPÄISCHE NORM

ICS 29.035.20 Supersedes EN 60684-3-211:2002


English version


Flexible insulating sleeving -
Part 3: Specifications for individual types of sleeving -
Sheet 211: Heat-shrinkable sleeving,
semi-rigid polyolefin, shrink ratio 2:1
(IEC 60684-3-211:2007)


Gaines isolantes souples -  Isolierschläuche -
Partie 3: Spécifications Teil 3: Anforderungen
pour types particuliers de gaines - für einzelne Schlauchtypen -
Feuille 211: Gaines thermorétractables, Blatt 211: Wärmeschrumpfschläuche,
en polyoléfine, semi-rigides, halbfestes Polyolefin,
à rapport de rétreint 2:1 Schrumpfverhältnis 2:1
(CEI 60684-3-211:2007) (IEC 60684-3-211:2007)




This European Standard was approved by CENELEC on 2007-04-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2007 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60684-3-211:2007 E

---------------------- Page: 2 ----------------------

EN 60684-3-211:2007 - 2 -
Foreword
The text of document 15/357/FDIS, future edition 3 of IEC 60684-3-211, prepared by IEC TC 15, Solid
electrical insulating materials, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 60684-3-211 on 2007-04-01.
This European Standard supersedes EN 60684-3-211:2002.
The major technical changes with regard to EN 60684-3-211:2002 concern a better alignment with
existing national specifications.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2008-01-01
national standard or by endorsement
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-04-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60684-3-211:2007 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60684-3-211:2007
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60684-1 2003 Flexible insulating sleeving - EN 60684-1 2003
Part 1: Definitions and general requirements


IEC 60684-2 1997 Flexible insulating sleeving - EN 60684-2 1997
A1 2003 Part 2: Methods of test A1 2003
A2 2005 A2 2005


IEC 60757 1983 Code for designation of colours HD 457 S1 1985


ISO 1817 2005 Rubber, vulcanized - - -
Determination of the effect of liquids

---------------------- Page: 4 ----------------------

INTERNATIONAL IEC


STANDARD 60684-3-211





Third edition
2007-02


Flexible insulating sleeving –
Part 3:
Specifications for individual types of sleeving –
Sheet 211: Heat-shrinkable sleeving, semi-rigid
polyolefin, shrink ratio 2:1
© IEC 2007 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale K
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

---------------------- Page: 5 ----------------------

– 2 – 60684-3-211 © IEC:2007(E)
CONTENTS

FOREWORD.3
INTRODUCTION.5

1 Scope.6
2 Normative references .6
3 Designation .7
4 Conditions of test .7
5 Requirements .7
6 Sleeving conformance .7

Table 1 – Dimensional requirements .7
Table 2 – Property requirements .8
Table 3 – Breakdown voltage.9
Table 4 – Fluid resistant property requirements for types C and D .9
Table 5 – Resistance to selected fluids .10

---------------------- Page: 6 ----------------------

60684-3-211 © IEC:2007(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FLEXIBLE INSULATING SLEEVING –

Part 3: Specifications for individual types of sleeving –
Sheet 211: Heat-shrinkable sleeving,
semi-rigid polyolefin, shrink ratio 2:1

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees
...