SIST EN 300 224 V2.1.1:2017
(Main)Land Mobile Service - Radio Equipment for use in a Paging Service operating within the frequency range 25 MHz - 470 MHz - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Land Mobile Service - Radio Equipment for use in a Paging Service operating within the frequency range 25 MHz - 470 MHz - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document applies to on-site and wide area paging equipment, operating in the frequency range of 25 MHz
to 470 MHz.
An on-site paging system is a privately owned and operated wireless communication system, used in a restricted and
predefined area, with the primary function to alert and/or inform ambulant people. The air interface of the system, using
a single radio channel, comprises at least one transmitter. The system may be extended to include a return, or talk-back
frequency. Mainly used for call acknowledgement, this frequency may also be used to supply some of the features of a
mobile radio service, or other two-way radio services, without the need to use a separate system.
Covering a larger geographical area, a wide-area system is typically associated with large organizations such as
emergency services and may include additional radio facilities and utilize different a frequency for return messaging,
which is outside the scope of the present document. These features should be tested against the relevant standard.
The present document specifies technical characteristics and methods of measurements for the following equipment
types:
1) base station transmitters and transcoders, with or without an external 50 Ω antenna connector;
2) base station receivers, with a permanent 50 Ω connector;
3) paging receiver, with or without an external 50 Ω antenna connector.
The existence of a Harmonised Standard does not imply the availability of the above frequency spectrum for the
particular types of equipment covered by the present document.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU under the conditions
identified in annex A and contains requirements to demonstrate that "... Radio equipment shall be so constructed that it
both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" [i.1].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.1] may apply to equipment within the scope of the
present document.
Storitev kopenskih mobilnih komunikacij - Radijska oprema za uporabo storitve osebnega klica, ki deluje v frekvenčnem območju od 25 MHz do 470 MHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument se uporablja za opremo za osebni klic za uporabo na mestu uporabe in na širokem območju, ki deluje v frekvenčnem območju 25–470 MHz.
Sistem za osebni klic na mestu uporabe je v zasebni lasti in zasebno upravljan sistem za brezžično komunikacijo, ki se uporablja na omejenem in vnaprej določenem območju in katerega primarna funkcija je opozoriti in/ali obvestiti ljudi, ki se lahko gibljejo. Radijski vmesnik sistema, ki uporablja en radijski kanal, sestavlja vsaj en tranzistor. Sistem se lahko razširi, da vključuje frekvenco za povratno komunikacijo. Frekvenca se uporablja predvsem za potrditev prejema klica, vendar se lahko uporablja tudi za nekatere funkcije mobilnih radijskih storitev, ali druge dvosmerne radijske storitve, ne da bi za to potrebovali ločen sistem.
Ker sistem pokriva večje geografsko območje, je običajno povezan z velikimi organizacijami, kot so reševalne službe, lahko pa vključuje tudi dodatne radijske zmogljivosti in uporablja drugo frekvenco za povratna sporočila, kar pa ne spada na področje uporabe tega dokumenta. Te funkcije je treba preskusiti v skladu z ustreznim standardom.
Ta dokument določa tehnične lastnosti in merilne metode za naslednje vrste opreme:
1) oddajniki in prekodirniki bazne postaje z ali brez zunanjega 50-ohmskega antenskega priključka;
2) sprejemniki bazne postaje s stalnim 50-ohmskim priključkom;
3) sprejemnik osebnega klica z ali brez zunanjega 50-ohmskega antenskega priključka.
Obstoj harmoniziranega standarda ne pomeni razpoložljivosti zgoraj navedenega frekvenčnega spektra za določene vrste opreme, ki je zajeta v tem dokumentu.
Ta dokument zajema bistvene zahteve člena 3.2 direktive 2014/53/EU pod pogoji iz dodatka A in navaja zahteve, s katerimi se dokazuje, da »... mora biti radijska oprema sestavljena tako, da učinkovito uporablja in tudi podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj« [i.1].
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta lahko uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena direktive o radijski opremi [i.1].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Land Mobile Service - Radio Equipment for use in a Paging Service operating within the frequency range 25 MHz - 470 MHz - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU33.070.20Sistem za osebni klicPaging systems33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 300 224 V2.1.1 (2017-06)SIST EN 300 224 V2.1.1:2017en01-september-2017SIST EN 300 224 V2.1.1:2017SLOVENSKI
STANDARD
SIST EN 300 224 V2.1.1:2017
ETSI EN 300 224 V2.1.1 (2017-06) Land Mobile Service; Radio Equipment for use in a Paging Service operating within the frequency range 25 MHz - 470 MHz; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 224 V2.1.1:2017
ETSI ETSI EN 300 224 V2.1.1 (2017-06) 2
Reference REN/ERM-TG30-315 Keywords harmonised standard, paging, radio, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 224 V2.1.1:2017
ETSI ETSI EN 300 224 V2.1.1 (2017-06) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 10 3.3 Abbreviations . 10 4 Testing for compliance with technical requirements . 11 4.1 Environmental profile . 11 4.2 Choice of model for testing . 11 4.2.0 General . 11 4.2.1 Auxiliary test equipment . 11 4.3 Mechanical and electrical design . 11 4.3.1 General . 11 4.3.2 Controls . 11 4.3.3 Transmitter shut-off facility . 11 5 Test conditions, power sources and ambient temperatures . 12 5.1 Normal and extreme test conditions . 12 5.2 Normal operational test conditions . 12 5.2.1 Normal temperature and humidity . 12 5.2.2 Normal test power source . 12 5.3 Extreme test conditions . 12 5.3.1 Procedure for tests at extreme temperatures . 12 5.3.2 Extreme temperature limits . 13 5.3.3 Extreme test power source . 13 5.3.4 Test power source . 14 6 Electrical test conditions . 14 6.1 Normal test signals and test modulation . 14 6.1.0 General . 14 6.1.1 Normal test signals for analogue speech . 14 6.1.2 Normal test signals for data . 14 6.2 Artificial antenna/load . 15 6.3 Test fixture for transmitters with an integral antenna . 15 6.4 Test site and general arrangement for measurements involving the use of radiated fields . 15 7 Transmitter . 16 7.0 General . 16 7.1 Frequency error . 16 7.1.0 General . 16 7.1.1 Definition . 16 7.1.2 Method of measurement . 16 7.1.3 Limits . 17 7.2 Carrier power . 17 7.2.1 Definition . 17 7.2.2 Carrier power (conducted) . 17 7.2.2.1 Method of measurement . 17 7.2.2.2 Limits . 17 7.2.3 Effective radiated power (on-site equipment with combined antenna) . 18 7.2.3.1 Method of measurement . 18 SIST EN 300 224 V2.1.1:2017
ETSI ETSI EN 300 224 V2.1.1 (2017-06) 4 7.2.3.2 Limits . 19 7.3 Adjacent channel power . 20 7.3.1 Definition . 20 7.3.2 Method of measurement . 20 7.3.3 Limits . 21 7.4 Frequency deviation . 21 7.4.0 General . 21 7.4.1 Definition . 21 7.4.2 Method of measurement . 21 7.4.3 Analogue signals within the audio bandwidth . 22 7.4.3.1 Method of measurement . 22 7.4.3.2 Limits . 22 7.4.4 Analogue signals above the audio bandwidth . 22 7.4.4.1 Method of measurement . 22 7.4.4.2 Limits . 22 7.5 Spurious emissions . 23 7.5.1 Definition . 23 7.5.2 Method of measurement . 23 7.5.2.0 General . 23 7.5.2.1 Method of measuring the spurious conducted power level . 24 7.5.2.2 Method of measuring the effective radiated spurious power level . 24 7.5.3 Limits . 25 7.6 Transmitter transient behaviour . 25 7.6.1 Definition . 25 7.6.1.0 General . 25 7.6.1.1 Keying criteria when the transmitter output power is switched on . 26 7.6.1.2 Keying criteria when the transmitter output power is switched off. 26 7.6.2 Method of measurement . 27 7.6.3 Limits . 28 7.7 Maximum transmission time . 28 7.7.1 Definition . 28 7.7.2 Method of measurement . 28 7.7.3 Limits . 28 8 Receiver Requirements. 28 8.1 Paging receivers reference sensitivity (field strength, data) . 28 8.1.1 Definition . 28 8.1.2 Method of measurement . 29 8.1.3 Limits . 29 8.2 Adjacent Channel Selectivity . 30 8.2.1 Definition . 30 8.2.2 Method of measurement . 30 8.2.3 Limits . 31 8.3 Co-channel rejection. 31 8.3.1 Definition . 31 8.3.2 Method of measurement . 31 8.3.3 Limits . 31 8.4 Intermodulation response rejection . 31 8.4.1 Definition . 31 8.4.2 Method of measurement . 32 8.4.3 Limits . 32 8.5 Spurious response rejection . 32 8.5.1 Definition . 32 8.5.2 Method of measurement . 33 8.5.3 Limits . 33 8.6 Spurious emissions . 34 8.6.1 Definition . 34 8.6.2 Method of measurement . 34 8.6.3 Limits . 34 9 Base station receivers . 34 9.1 Measured sensitivity for analogue speech . 34 SIST EN 300 224 V2.1.1:2017
ETSI ETSI EN 300 224 V2.1.1 (2017-06) 5 9.1.1 Definition . 34 9.1.2 Method of measurement . 34 9.1.3 Limits . 35 9.2 Measured sensitivity for messages . 35 9.2.1 Definition . 35 9.2.2 Method of measurement . 35 9.2.3 Limits . 35 9.3 Co-channel rejection for analogue speech . 35 9.3.1 Definition . 35 9.3.2 Method of measurement . 35 9.3.3 Limits . 36 9.4 Co-channel rejection for messages . 36 9.4.1 Definition . 36 9.4.2 Method of measurement . 36 9.4.3 Limits . 36 9.5 Adjacent channel selectivity for analogue speech . 37 9.5.1 Definition . 37 9.5.2 Method of measurement . 37 9.5.3 Limits . 37 9.6 Adjacent channel selectivity for messages . 37 9.6.1 Definition . 37 9.6.2 Method of measurement . 38 9.6.3 Limits . 38 9.7 Spurious response immunity for analogue speech . 38 9.7.1 Definition . 38 9.7.2 Method of measurement . 39 9.7.3 Limit . 39 9.8 Spurious response immunity for messages . 39 9.8.1 Definition . 39 9.8.2 Method of measurement . 39 9.8.3 Limit . 40 9.9 Intermodulation immunity for analogue speech . 40 9.9.1 Definition . 40 9.9.2 Method of measurement . 40 9.9.3 Limit . 41 9.10 Intermodulation immunity for messages . 41 9.10.1 Definition . 41 9.10.2 Method of measurement . 41 9.10.3 Limit . 42 9.11 Blocking immunity or desensitization for analogue speech . 42 9.11.1 Definition . 42 9.11.2 Method of measurement . 42 9.11.3 Limit . 43 9.12 Blocking immunity or desensitization for messages . 43 9.12.1 Definition . 43 9.12.2 Method of measurement . 43 9.12.3 Limit . 44 9.13 Spurious emissions . 44 9.13.1 Definition . 44 9.13.2 Method of measurement . 44 9.13.2.1 Conducted spurious components . 44 9.13.2.2 Radiated spurious components . 44 9.13.3 Limits . 44 10 Measurement uncertainties .
...
ETSI EN 300 224 V2.1.1 (2017-06)
HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio Equipment for use in a Paging Service
operating within the frequency range 25 MHz - 470 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 300 224 V2.1.1 (2017-06)
Reference
REN/ERM-TG30-315
Keywords
harmonised standard, paging, radio, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 224 V2.1.1 (2017-06)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Testing for compliance with technical requirements . 11
4.1 Environmental profile . 11
4.2 Choice of model for testing . 11
4.2.0 General . 11
4.2.1 Auxiliary test equipment . 11
4.3 Mechanical and electrical design . 11
4.3.1 General . 11
4.3.2 Controls . 11
4.3.3 Transmitter shut-off facility . 11
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Normal operational test conditions . 12
5.2.1 Normal temperature and humidity . 12
5.2.2 Normal test power source . 12
5.3 Extreme test conditions . 12
5.3.1 Procedure for tests at extreme temperatures . 12
5.3.2 Extreme temperature limits . 13
5.3.3 Extreme test power source . 13
5.3.4 Test power source . 14
6 Electrical test conditions . 14
6.1 Normal test signals and test modulation . 14
6.1.0 General . 14
6.1.1 Normal test signals for analogue speech . 14
6.1.2 Normal test signals for data . 14
6.2 Artificial antenna/load . 15
6.3 Test fixture for transmitters with an integral antenna . 15
6.4 Test site and general arrangement for measurements involving the use of radiated fields . 15
7 Transmitter . 16
7.0 General . 16
7.1 Frequency error . 16
7.1.0 General . 16
7.1.1 Definition . 16
7.1.2 Method of measurement . 16
7.1.3 Limits . 17
7.2 Carrier power . 17
7.2.1 Definition . 17
7.2.2 Carrier power (conducted) . 17
7.2.2.1 Method of measurement . 17
7.2.2.2 Limits . 17
7.2.3 Effective radiated power (on-site equipment with combined antenna) . 18
7.2.3.1 Method of measurement . 18
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 224 V2.1.1 (2017-06)
7.2.3.2 Limits . 19
7.3 Adjacent channel power . 20
7.3.1 Definition . 20
7.3.2 Method of measurement . 20
7.3.3 Limits . 21
7.4 Frequency deviation . 21
7.4.0 General . 21
7.4.1 Definition . 21
7.4.2 Method of measurement . 21
7.4.3 Analogue signals within the audio bandwidth . 22
7.4.3.1 Method of measurement . 22
7.4.3.2 Limits . 22
7.4.4 Analogue signals above the audio bandwidth . 22
7.4.4.1 Method of measurement . 22
7.4.4.2 Limits . 22
7.5 Spurious emissions . 23
7.5.1 Definition . 23
7.5.2 Method of measurement . 23
7.5.2.0 General . 23
7.5.2.1 Method of measuring the spurious conducted power level . 24
7.5.2.2 Method of measuring the effective radiated spurious power level . 24
7.5.3 Limits . 25
7.6 Transmitter transient behaviour . 25
7.6.1 Definition . 25
7.6.1.0 General . 25
7.6.1.1 Keying criteria when the transmitter output power is switched on . 26
7.6.1.2 Keying criteria when the transmitter output power is switched off. 26
7.6.2 Method of measurement . 27
7.6.3 Limits . 28
7.7 Maximum transmission time . 28
7.7.1 Definition . 28
7.7.2 Method of measurement . 28
7.7.3 Limits . 28
8 Receiver Requirements. 28
8.1 Paging receivers reference sensitivity (field strength, data) . 28
8.1.1 Definition . 28
8.1.2 Method of measurement . 29
8.1.3 Limits . 29
8.2 Adjacent Channel Selectivity . 30
8.2.1 Definition . 30
8.2.2 Method of measurement . 30
8.2.3 Limits . 31
8.3 Co-channel rejection. 31
8.3.1 Definition . 31
8.3.2 Method of measurement . 31
8.3.3 Limits . 31
8.4 Intermodulation response rejection . 31
8.4.1 Definition . 31
8.4.2 Method of measurement . 32
8.4.3 Limits . 32
8.5 Spurious response rejection . 32
8.5.1 Definition . 32
8.5.2 Method of measurement . 33
8.5.3 Limits . 33
8.6 Spurious emissions . 34
8.6.1 Definition . 34
8.6.2 Method of measurement . 34
8.6.3 Limits . 34
9 Base station receivers . 34
9.1 Measured sensitivity for analogue speech . 34
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 224 V2.1.1 (2017-06)
9.1.1 Definition . 34
9.1.2 Method of measurement . 34
9.1.3 Limits . 35
9.2 Measured sensitivity for messages . 35
9.2.1 Definition . 35
9.2.2 Method of measurement . 35
9.2.3 Limits . 35
9.3 Co-channel rejection for analogue speech . 35
9.3.1 Definition . 35
9.3.2 Method of measurement . 35
9.3.3 Limits . 36
9.4 Co-channel rejection for messages . 36
9.4.1 Definition . 36
9.4.2 Method of measurement . 36
9.4.3 Limits . 36
9.5 Adjacent channel selectivity for analogue speech . 37
9.5.1 Definition . 37
9.5.2 Method of measurement . 37
9.5.3 Limits . 37
9.6 Adjacent channel selectivity for messages . 37
9.6.1 Definition . 37
9.6.2 Method of measurement . 38
9.6.3 Limits . 38
9.7 Spurious response immunity for analogue speech . 38
9.7.1 Definition . 38
9.7.2 Method of measurement . 39
9.7.3 Limit . 39
9.8 Spurious response immunity for messages . 39
9.8.1 Definition . 39
9.8.2 Method of measurement . 39
9.8.3 Limit . 40
9.9 Intermodulation immunity for analogue speech . 40
9.9.1 Definition . 40
9.9.2 Method of measurement . 40
9.9.3 Limit . 41
9.10 Intermodulation immunity for messages . 41
9.10.1 Definition . 41
9.10.2 Method of measurement . 41
9.10.3 Limit . 42
9.11 Blocking immunity or desensitization for analogue speech . 42
9.11.1 Definition . 42
9.11.2 Method of measurement . 42
9.11.3 Limit . 43
9.12 Blocking immunity or desensitization for messages . 43
9.12.1 Definition . 43
9.12.2 Method of measurement . 43
9.12.3 Limit . 44
9.13 Spurious emissions . 44
9.13.1 Definition . 44
9.13.2 Method of measurement . 44
9.13.2.1 Conducted spurious components . 44
9.13.2.2 Radiated spurious components . 44
9.13.3 Limits . 44
10 Measurement uncertainties . 44
10.1 General . 44
10.2 Measurement Uncertainty Values .
...
Draft ETSI EN 300 224 V2.0.0 (2017-03)
HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio Equipment for use in a Paging Service
operating within the frequency range 25 MHz - 470 MHz;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 224 V2.0.0 (2017-03)
Reference
REN/ERM-TG30-315
Keywords
harmonised standard, paging, radio, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 224 V2.0.0 (2017-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Testing for compliance with technical requirements . 11
4.1 Environmental profile . 11
4.2 Choice of model for testing . 11
4.2.0 General . 11
4.2.1 Auxiliary test equipment . 11
4.3 Mechanical and electrical design . 11
4.3.1 General . 11
4.3.2 Controls . 11
4.3.3 Transmitter shut-off facility . 11
5 Test conditions, power sources and ambient temperatures . 12
5.1 Normal and extreme test conditions . 12
5.2 Normal operational test conditions . 12
5.2.1 Normal temperature and humidity . 12
5.2.2 Normal test power source . 12
5.3 Extreme test conditions . 12
5.3.1 Procedure for tests at extreme temperatures . 12
5.3.2 Extreme temperature limits . 13
5.3.3 Extreme test power source . 13
5.3.4 Test power source . 14
6 Electrical test conditions . 14
6.1 Normal test signals and test modulation . 14
6.1.0 General . 14
6.1.1 Normal test signals for analogue speech . 14
6.1.2 Normal test signals for data . 14
6.2 Artificial antenna/load . 15
6.3 Test fixture for transmitters with an integral antenna . 15
6.4 Test site and general arrangement for measurements involving the use of radiated fields . 15
7 Transmitter . 16
7.0 General . 16
7.1 Frequency error . 16
7.1.0 General . 16
7.1.1 Definition . 16
7.1.2 Method of measurement . 16
7.1.3 Limits . 17
7.2 Carrier power . 17
7.2.1 Definition . 17
7.2.2 Carrier power (conducted) . 17
7.2.2.1 Method of measurement . 17
7.2.2.2 Limits . 17
7.2.3 Effective radiated power (on-site equipment with combined antenna) . 18
7.2.3.1 Method of measurement . 18
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 224 V2.0.0 (2017-03)
7.2.3.2 Limits . 19
7.3 Adjacent channel power . 20
7.3.1 Definition . 20
7.3.2 Method of measurement . 20
7.3.3 Limits . 21
7.4 Frequency deviation . 21
7.4.0 General . 21
7.4.1 Definition . 21
7.4.2 Method of measurement . 21
7.4.3 Analogue signals within the audio bandwidth . 22
7.4.3.1 Method of measurement . 22
7.4.3.2 Limits . 22
7.4.4 Analogue signals above the audio bandwidth . 22
7.4.4.1 Method of measurement . 22
7.4.4.2 Limits . 22
7.5 Spurious emissions . 23
7.5.1 Definition . 23
7.5.2 Method of measurement . 23
7.5.2.0 General . 23
7.5.2.1 Method of measuring the spurious conducted power level . 24
7.5.2.2 Method of measuring the effective radiated spurious power level . 24
7.5.3 Limits . 25
7.6 Transmitter transient behaviour . 25
7.6.1 Definition . 25
7.6.1.0 General . 25
7.6.1.1 Keying criteria when the transmitter output power is switched on . 25
7.6.1.2 Keying criteria when the transmitter output power is switched off. 26
7.6.2 Method of measurement . 27
7.6.3 Limits . 28
7.7 Maximum transmission time . 28
7.7.1 Definition . 28
7.7.2 Method of measurement . 28
7.7.3 Limits . 28
8 Receiver Requirements. 28
8.1 Paging receivers reference sensitivity (field strength, data) . 28
8.1.1 Definition . 28
8.1.2 Method of measurement . 29
8.1.3 Limits . 29
8.2 Adjacent Channel Selectivity . 30
8.2.1 Definition . 30
8.2.2 Method of measurement . 30
8.2.3 Limits . 31
8.3 Co-channel rejection. 31
8.3.1 Definition . 31
8.3.2 Method of measurement . 31
8.3.3 Limits . 31
8.4 Intermodulation response rejection . 31
8.4.1 Definition . 31
8.4.2 Method of measurement . 32
8.4.3 Limits . 32
8.5 Spurious response rejection . 32
8.5.1 Definition . 32
8.5.2 Method of measurement . 33
8.5.3 Limits . 33
8.6 Spurious emissions . 34
8.6.1 Definition . 34
8.6.2 Method of measurement . 34
8.6.3 Limits . 34
9 Base station receivers . 34
9.1 Measured sensitivity for analogue speech . 34
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 224 V2.0.0 (2017-03)
9.1.1 Definition . 34
9.1.2 Method of measurement . 34
9.1.3 Limits . 35
9.2 Measured sensitivity for messages . 35
9.2.1 Definition . 35
9.2.2 Method of measurement . 35
9.2.3 Limits . 35
9.3 Co-channel rejection for analogue speech . 35
9.3.1 Definition . 35
9.3.2 Method of measurement . 35
9.3.3 Limits . 36
9.4 Co-channel rejection for messages . 36
9.4.1 Definition . 36
9.4.2 Method of measurement . 36
9.4.3 Limits . 36
9.5 Adjacent channel selectivity for analogue speech . 37
9.5.1 Definition . 37
9.5.2 Method of measurement . 37
9.5.3 Limits . 37
9.6 Adjacent channel selectivity for messages . 37
9.6.1 Definition . 37
9.6.2 Method of measurement . 38
9.6.3 Limits . 38
9.7 Spurious response immunity for analogue speech . 38
9.7.1 Definition . 38
9.7.2 Method of measurement . 39
9.7.3 Limit . 39
9.8 Spurious response immunity for messages . 39
9.8.1 Definition . 39
9.8.2 Method of measurement . 39
9.8.3 Limit . 40
9.9 Intermodulation immunity for analogue speech . 40
9.9.1 Definition . 40
9.9.2 Method of measurement . 40
9.9.3 Limit . 41
9.10 Intermodulation immunity for messages . 41
9.10.1 Definition . 41
9.10.2 Method of measurement . 41
9.10.3 Limit . 42
9.11 Blocking immunity or desensitization for analogue speech . 42
9.11.1 Definition . 42
9.11.2 Method of measurement . 42
9.11.3 Limit . 43
9.12 Blocking immunity or desensitization for messages . 43
9.12.1 Definition . 43
9.12.2 Method of measurement . 43
9.12.3 Limit . 43
9.13 Spurious emissions . 44
9.13.1 Definition . 44
9.13.2 Method of measurement . 44
9.13.2.1 Conducted spurious components . 44
9.13.2.2 Radiated spurious components . 44
9.13.3 Limits . 44
10 Measurement uncertainties . 44
10.1 General . 44
10.2 Measurement Uncertainty Values .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.