SIST EN ISO 13000-1:2006
(Main)Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2005)
This part of ISO 13000 specifies the requirements for processed unfilled polytetrafluoroethylene (PTFE) products, which may occur in several forms. The PTFE used to make the semi-finished product is described in ISO 12086-1 and, as provided in ISO 12086-1, may contain up to 1 % of a comonomer. The PTFE used to make the semi-finished product may be virgin, reprocessed or recycled resin. The addition of up to 1, 5 % by mass of pigment or colorant is permitted. This part of ISO 13000 allows for four grades based on tensile strength and elongation at break. The semi-finished products can be as- processed (type P) or dimensionally stabilized (type S) and may also have specified electrical properties or other properties when they are required for an application.
Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil 1: Anforderungen und Bezeichnung (ISO 13000-1:2005)
Dieser Teil von ISO 13000 legt Anforderungen für verarbeitete, ungefüllte Polytetrafluorethylen (PTFE)-Produkte, die in verschiedenen Formen vorliegen können, fest. Das zur Herstellung von PTFE-Halbzeug verwendete PTFE wird in ISO 12086 1 beschrieben und darf nach ISO 12086-1 Angaben bis zu 1 % eines Comonomer enthalten. Bei dem zur Herstellung von Halbzeug verwendeten PTFE kann es sich um virginales oder wiederverarbeitetes Harz handeln. Der Zusatz von Pigmenten oder Farbstoffen ist bis zu einem Massenanteil von 1,5 % zulässig. Hinsichtlich der Zugfestigkeit und Bruchdehnung sind in diesem Teil von ISO 13000 vier verschiedene Klassen vorgesehen. Das Halbzeug kann ohne Nachbehandlung (Typ P) oder dimensionsstabilisiert sein (Typ S) und kann festgelegte elektrische Eigenschaften oder andere Merkmale aufweisen, sofern sie für eine bestimmte Anwendung vorgeschrieben sind.
ANMERKUNG Zur Information wird in Anhang A auf andere Spezifikationsnormen für Halbzeuge aus Polytetrafluorethylen verwiesen.
Plastiques - Semi-produits en polytétrafluoroéthylene (PTFE) - Partie 1: Spécifications et désignation (ISO 13000-1:2005)
L'ISO 13000-1:2005 spécifie les exigences relatives aux produits en polytétrafluoroéthylène (PTFE) mis en oeuvre et non chargés qui peuvent se présenter sous diverses formes. Le PTFE utilisé pour fabriquer le semi-produit est décrit dans l'ISO 12086-1 et, comme cela est indiqué dans l'ISO 12086-1 peut contenir jusqu'à 1 % d'un quelconque comonomère. Le PTFE utilisé pour fabriquer le semi-produit peut être une résine vierge, régénérée ou recyclée. Il est permis d'ajouter jusqu'à 1,5 % en masse de pigment ou colorant. L'ISO 13000-1 admet l'emploi de quatre qualités basées sur la résistance à la traction et l'allongement à la rupture. Les semi-produits peuvent être bruts de mise en oeuvre (type P) ou dimensionnellement stabilisés (type S) et ils peuvent être caractérisés par certaines propriétés électriques ou autres, lorsqu'elles sont requises pour une application donnée.
Polimerni materiali – Polizdelki iz politetrafluoroetilena (PTFE) – 1. del: Zahteve in označevanje(ISO/DIS 13000-1:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13000-1:2006
01-april-2006
1DGRPHãþD
SIST EN ISO 13000-1:1999
3ROLPHUQLPDWHULDOL±3ROL]GHONLL]SROLWHWUDIOXRURHWLOHQD 37)( ±GHO =DKWHYHLQ
R]QDþHYDQMH ,62',6
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements
and designation (ISO 13000-1:2005)
Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil 1: Anforderungen und
Bezeichnung (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylene (PTFE) - Partie 1: Spécifications et
désignation (ISO 13000-1:2005)
Ta slovenski standard je istoveten z: EN ISO 13000-1:2005
ICS:
83.140.01 Izdelki iz gume in polimernih Rubber and plastics products
materialov na splošno in general
SIST EN ISO 13000-1:2006 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13000-1:2006
---------------------- Page: 2 ----------------------
SIST EN ISO 13000-1:2006
EUROPEAN STANDARD
EN ISO 13000-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2005
ICS 83.140.01 Supersedes EN ISO 13000-1:1997
English Version
Plastics - Polytetrafluoroethylene (PTFE) semi-finished products
- Part 1: Requirements and designation (ISO 13000-1:2005)
Plastiques - Semi-produits en polytétrafluoroéthylène Kunststoffe - Polytetrafluorethylen (PTFE)-Halbzeuge - Teil
(PTFE) - Partie 1: Spécifications et désignation (ISO 1: Anforderungen und Bezeichnung (ISO 13000-1:2005)
13000-1:2005)
This European Standard was approved by CEN on 4 November 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13000-1:2005: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13000-1:2006
EN ISO 13000-1:2005 (E)
Foreword
This document (EN ISO 13000-1:2005) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2006, and conflicting national standards
shall be withdrawn at the latest by May 2006.
This document supersedes EN ISO 13000-1:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 13000-1:2005 has been approved by CEN as EN ISO 13000-1:2005 without any
modifications.
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13000-1:2006
INTERNATIONAL ISO
STANDARD 13000-1
Second edition
2005-11-15
Plastics — Polytetrafluoroethylene
(PTFE) semi-finished products —
Part 1:
Requirements and designation
Plastiques — Semi-produits en polytétrafluoroéthylène (PTFE) —
Partie 1: Spécifications et désignation
Reference number
ISO 13000-1:2005(E)
©
ISO 2005
---------------------- Page: 5 ----------------------
SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terminology . 1
3.1 Terms and definitions. 1
3.2 Abbreviated terms and symbols . 2
4 Requirements for PTFE semi-finished products . 2
4.1 General. 2
4.2 Dimensions and dimensional tolerances.2
4.3 Tensile strength and percentage elongation at break . 4
4.4 Dimensional stability. 4
4.5 Density . 5
4.6 Hardness. 5
4.7 Colour . 5
4.8 Dielectric strength (DS), breakdown voltage and electrical flaws. 5
4.9 Requirements that may be specified depending on the specific application . 7
5 Format for presenting a specification . 7
5.1 General. 7
5.2 Order of presenting codes. 7
5.3 Examples of coding a specification. 8
Annex A (informative) Standard specifications for semi-finished products of
polytetrafluoroethylene. 10
© ISO 2005 – All rights reserved iii
---------------------- Page: 7 ----------------------
SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13000-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This second edition cancels and replaces the first edition (ISO 13000-1:1997), which has been technically
revised.
ISO 13000 consists of the following parts, under the general title Plastics — Polytetrafluoroethylene (PTFE)
semi-finished products:
— Part 1: Requirements and designation
— Part 2: Preparation of test specimens and determination of properties
iv © ISO 2005 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13000-1:2006
INTERNATIONAL STANDARD ISO 13000-1:2005(E)
Plastics — Polytetrafluoroethylene (PTFE) semi-finished
products —
Part 1:
Requirements and designation
1 Scope
This part of ISO 13000 specifies the requirements for processed unfilled polytetrafluoroethylene (PTFE)
products, which may occur in several forms. The PTFE used to make the semi-finished product is described in
ISO 12086-1 and, as provided in ISO 12086-1, may contain up to 1 % of a comonomer. The PTFE used to
make the semi-finished product may be virgin, reprocessed or recycled resin. The addition of up to 1,5 % by
mass of pigment or colorant is permitted. This part of ISO 13000 allows for four grades based on tensile
strength and elongation at break. The semi-finished products can be as-processed (type P) or dimensionally
stabilized (type S) and may also have specified electrical properties or other properties when they are required
for an application.
NOTE References to other standard specifications for semi-finished products made from polytetrafluoroethylene are
listed in Annex A for information.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 472, Plastics — Vocabulary
ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special
characteristics
ISO 12086-1, Plastics — Fluoropolymer dispersions and moulding and extrusion materials — Part 1:
Designation system and basis for specifications
ISO 13000-2, Plastics — Polytetrafluoroethylene (PTFE) semi-finished products — Part 2: Preparation of test
specimens and determination of properties
3 Terminology
3.1 Terms and definitions
For the purposes of this part of ISO 13000, the terms and definitions given in ISO 472 and ISO 12086-1 and
the following terms and definitions apply.
© ISO 2005 – All rights reserved 1
---------------------- Page: 9 ----------------------
SIST EN ISO 13000-1:2006
ISO 13000-1:2005(E)
3.1.1
moulded basic shape
〈PTFE〉 semi-finished product made by preforming and sintering without additional processing
3.1.2
semi-finished product
material, in the form of skived tape, sheets, rods, tubes, tubing, moulded basic shapes or special shapes, that
is produced for use either directly without further fabrication or in fabricating end use products, or both
3.1.3
skived tape
film or sheet prepared by cutting, slicing or shaving
NOTE The term “veneered tape” is deprecated.
3.2 Abbreviated terms and symbols
The abbreviated terms given in ISO 1043-1 are applicable to this part of ISO 13000.
4 Requirements for PTFE semi-finished products
4.1 General
After considering the specific shape, dimensions and dimensional tolerances, the primary basis for specifying
a semi-finished product of PTFE is the tensile strength and percentage elongation at break of the product.
Tests to determine the values for specification shall be run in accordance with the methods in ISO 13000-2.
The semi-finished product is identified as “type P” for as-processed or “type S” for stabilized and also may be
desi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.