SIST EN ISO 13894-2:2015

High-pressure decorative laminates - Composite elements - Part 2 : Specifications for composite elements with wood-based substrates for interior use (ISO 13894-2:2005)

This part of ISO 13894 describes the general properties of composite elements surfaced, and possibly edged,
with high-pressure decorative laminate (HPDL) as defined in Clause 3. The composite elements specified in
this part of ISO 13894 consist of HPDL sheet material adhesively bonded to one or both sides of a woodbased
substrate, and are intended for normal interior use.
Requirements for special applications, e.g. where the product is subjected to extreme conditions of heat or
moisture, are not part of this part of ISO 13894, although Part 1 of this International Standard describes test
methods for additional properties which may be applicable to such applications (see ISO 13894-1:2000,
Subclause 3.1, Note 3).
Test methods and performance levels for special applications shall be agreed between customer and supplier.
Information concerning test methods for special applications is given in Annex A.

Dekorative Hochdruck-Laminate - Verbundelemente - Teil 2: Spezifikationen für Verbundelemente mit holzbasierten Substraten für Innenräume (ISO 13894-2:2005)

Stratifiés décoratifs haute pression - Éléments composites - Partie 2: Spécifications des éléments composites avec substrats à base de bois pour l'usage intérieur (ISO 13894-2:2005)

L'ISO 13894-2:2005 décrit les propriétés générales des éléments composites revêtus, et éventuellement plaqués avec chants, de stratifiés décoratifs haute pression (HPDL). Les éléments composites spécifiés se composent de feuilles de HPDL collées sur l'une ou les deux faces d'un substrat à base de bois et sont destinés à un usage intérieur normal.
Les exigences relatives à des applications particulières, par exemple lorsque le produit est soumis à des conditions extrêmes de chaleur ou d'humidité, ne sont pas spécifiées.

Dekorativni visokotlačni laminati - Kompozitni elementi - 2. del: Specifikacije za kompozitne elemente z leseno podlago za notranjo uporabo (ISO 13894-2:2005)

General Information

• Status: Published
• Public Enquiry End Date: 11-Jan-2015
• Publication Date: 23-Apr-2015
• ICS: 83.140.20 - Laminated sheets
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 17-Apr-2015
• Due Date: 22-Jun-2015
• Completion Date: 24-Apr-2015
• Ref Project: EN ISO 13894-2:2015 - High-pressure decorative laminates - Composite elements - Part 2 : Specifications for composite elements with wood-based substrates for interior use (ISO 13894-2:2005)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13894-2:2015
01-junij-2015
'HNRUDWLYQLYLVRNRWODþQLODPLQDWL.RPSR]LWQLHOHPHQWLGHO6SHFLILNDFLMH]D
NRPSR]LWQHHOHPHQWH]OHVHQRSRGODJR]DQRWUDQMRXSRUDER,62
High-pressure decorative laminates - Composite elements - Part 2 : Specifications for
composite elements with wood-based substrates for interior use (ISO 13894-2:2005)
Dekorative Hochdruck-Laminate - Verbundelemente - Teil 2: Spezifikationen für
Verbundelemente mit holzbasierten Substraten für Innenräume (ISO 13894-2:2005)
Stratifiés décoratifs haute pression - Éléments composites - Partie 2: Spécifications des
éléments composites avec substrats à base de bois pour l'usage intérieur (ISO 13894-
2:2005)
Ta slovenski standard je istoveten z: EN ISO 13894-2:2015
ICS:
83.140.20 /DPLQDWQHSORãþH Laminated sheets
SIST EN ISO 13894-2:2015 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13894-2:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 13894-2:2015

EUROPEAN STANDARD
EN ISO 13894-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2015
ICS 83.140.20; 97.150
English Version
High-pressure decorative laminates - Composite elements - Part
2 : Specifications for composite elements with wood-based
substrates for interior use (ISO 13894-2:2005)
Stratifiés décoratifs haute pression - Éléments composites - Dekorative Hochdruck-Laminate - Verbundelemente - Teil
Partie 2: Spécifications des éléments composites avec 2: Spezifikationen für Verbundelemente mit holzbasierten
substrats à base de bois pour l'usage intérieur (ISO 13894- Substraten für Innenräume (ISO 13894-2:2005)
2:2005)
This European Standard was approved by CEN on 7 April 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13894-2:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 13894-2:2015
EN ISO 13894-2:2015 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 13894-2:2015
EN ISO 13894-2:2015 (E)
Foreword
The text of ISO 13894-2:2005 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 13894-2:2015 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2015, and conflicting national standards shall be withdrawn at
the latest by October 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13894-2:2005 has been approved by CEN as EN ISO 13894-2:2015 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 13894-2:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 13894-2:2015


INTERNATIONAL ISO
STANDARD 13894-2
First edition
2005-07-15

High-pressure decorative laminates —
Composite elements —
Part 2:
Specifications for composite elements
with wood-based substrates for interior
use
Stratifiés décoratifs haute pression — Éléments composites —
Partie 2: Spécifications des éléments composites avec substrats à base
de bois pour l'usage intérieur




Reference number
ISO 13894-2:2005(E)
©
ISO 2005

---------------------- Page: 7 ----------------------

SIST EN ISO 13894-2:2015
ISO 13894-2:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 13894-2:2015
ISO 13894-2:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Requirements . 2
5 Properties . 2
5.1 Appearance . 2
5.2 Dimensional tolerances . 3
5.3 Surface bond strength. 6
5.4 Perpendicular tensile strength. 6
5.5 Glue-line quality. 6
5.6 Substrate protection against water vapour (thickness swell) . 6
5.7 Surface impact resistance . 6
Annex A (informative) Optional properties. 7
A.1 General. 7
A.2 Resistance to axial withdrawal of wood screws (screw-holding). 7
A.3 Resistance to elevated temperature (short-term exposure) . 7
A.4 Resistance to elevated temperature (long-term exposure). 7
A.5 Resistance to water vapour . 8
A.6 Flexural strength/flexural modulus of elasticity.8
A.7 Continuous-load capability. 9
A.8 Water resistance (edge swell) . 9
Annex B (informative) Reaction to fire . 10
Annex C (informative) Formaldehyde emission. 11

© ISO 2005 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 13894-2:2015
ISO 13894-2:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13894-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
ISO 13894 consists of the following parts, under the general title High-pressure decorative laminates —
Composite elements:
— Part 1: Test methods
— Part 2: Specifications for composite elements with wood-based substrates for interior use

iv © ISO 2005 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 13894-2:2015
INTERNATIONAL STANDARD ISO 13894-2:2005(E)

High-pressure decorative laminates — Composite elements —
Part 2:
Specifications for composite elements with wood-based
substrates for interior use
1 Scope
This part of ISO 13894 describes the general properties of composite elements surfaced, and possibly edged,
with high-pressure decorative laminate (HPDL) as defined in Clause 3. The composite elements specified in
this part of ISO 13894 consist of HPDL sheet material adhesively bonded to one or both sides of a wood-
based substrate, and are intended for normal interior use.
Requirements for special applications, e.g. where the product is subjected to extreme conditions of heat or
moisture, are not part of this part of ISO 13894, although Part 1 of this International Standard describes test
methods for additional properties which may be applicable to such applications (see ISO 13894-1:2000,
Subclause 3.1, Note 3).
Test methods and performance levels for special applications shall be agreed between customer and supplier.
Information concerning test methods for special applications is given in Annex A.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1096, Plywood — Classification
ISO 4586-1:2004, High-pressure decorative laminates — Sheets made from thermosetting resins — Part 1:
Classification and specifications
ISO 13894-1:2000, High-pressure decorative laminates — Composite elements — Part 1: Test methods
ISO 17064, Wood-based panels — Fibreboard, particleboard and oriented strand board (OSB) — Vocabulary
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
high-pressure decorative laminate (HPDL) composite element with wood-based substrate
composite board produced by adhesively bonding high-pressure decorative laminate (HPDL) sheet material to
one or both sides of a wood-based substrate
© ISO 2005 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 13894-2:2015
ISO 13894-2:2005(E)
3.2
high-pressure decorative laminate(s)
HPDL
HPL
See Definition 3.1 in ISO 4586-1:2004.
3.3
wood-based substrate
particleboard, oriented-strand board, fibreboard (ISO 17064) or plywood (ISO 1096)
NOTE Solid timber and blockboard
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dekorative Hochdruck-Laminate - Verbundelemente - Teil 2: Spezifikationen für Verbundelemente mit holzbasierten Substraten für Innenräume (ISO 13894-2:2005)Stratifiés décoratifs haute pression - Éléments composites - Partie 2: Spécifications des éléments composites avec substrats à base de bois pour l'usage intérieur (ISO 13894-2:2005)High-pressure decorative laminates - Composite elements - Part 2 : Specifications for composite elements with wood-based substrates for interior use (ISO 13894-2:2005)83.140.20Laminated sheetsICS:Ta slovenski standard je istoveten z:FprEN ISO 13894-2kSIST FprEN ISO 13894-2:2014en,de01-december-2014kSIST FprEN ISO 13894-2:2014SLOVENSKI
STANDARD



kSIST FprEN ISO 13894-2:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 13894-2
October 2014 ICS 83.140.20; 97.150 English Version
High-pressure decorative laminates - Composite elements - Part 2 : Specifications for composite elements with wood-based substrates for interior use (ISO 13894-2:2005)
Stratifiés décoratifs haute pression - Éléments composites -Partie 2: Spécifications des éléments composites avec substrats à base de bois pour l'usage intérieur (ISO 13894-2:2005)
Dekorative Hochdruck-Laminate - Verbundelemente - Teil 2: Spezifikationen für Verbundelemente mit holzbasierten Substraten für Innenräume (ISO 13894-2:2005) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 249.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 13894-2:2014 EkSIST FprEN ISO 13894-2:2014



FprEN ISO 13894-2:2014 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 13894-2:2014



FprEN ISO 13894-2:2014 (E) 3 Foreword The text of ISO 13894-2:2005 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 13894-2:2014 by Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This document is currently submitted to the Unique Acceptance Procedure. Endorsement notice The text of ISO 13894-2:2005 has been approved by CEN as FprEN ISO 13894-2:2014 without any modification. kSIST FprEN ISO 13894-2:2014



kSIST FprEN ISO 13894-2:2014



Reference numberISO 13894-2:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO13894-2First edition2005-07-15High-pressure decorative laminates — Composite elements — Part 2: Specifications for composite elements with wood-based substrates for interior use Stratifiés décoratifs haute pression — Éléments composites — Partie 2: Spécifications des éléments composites avec substrats à base de bois pour l'usage intérieur
kSIST FprEN ISO 13894-2:2014



ISO 13894-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.org Published in Switzerland
ii
© ISO 2005 – All rights reserved
kSIST FprEN ISO 13894-2:2014



ISO 13894-2:2005(E) © ISO 2005 – All rights reserved
iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Terms and definitions.1 4 Requirements.2 5 Properties.2 5.1 Appearance.2 5.2 Dimensional tolerances.3 5.3 Surface bond strength.6 5.4 Perpendicular tensile strength.6 5.5 Glue-line quality.6 5.6 Substrate protection against water vapour (thickness swell).6 5.7 Surface impact resistance.6 Annex A (informative)
Optional properties.7 A.1 General.7 A.2 Resistance to axial withdrawal of wood screws (screw-holding).7 A.3 Resistance to elevated temperature (short-term exposure).7 A.4 Resistance to elevated temperature (long-term exposure).7 A.5 Resistance to water vapour.8 A.6 Flexural strength/flexural modulus of elasticity.8 A.7 Continuous-load capability.9 A.8 Water resistance (edge swell).9 Annex B (informative)
Reaction to fire.10 Annex C (informative)
Formaldehyde emission.11
kSIST FprEN ISO 13894-2:2014



ISO 13894-2:2005(E) iv
© ISO 2005 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13894-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products. ISO 13894 consists of the following parts, under the general title High-pressure decorative laminates — Composite elements: — Part 1: Test methods — Part 2: Specifications for composite elements with wood-based substrates for interior use
kSIST FprEN ISO 13894-2:2014



INTERNATIONAL STANDARD ISO 13894-2:2005(E) © ISO 2005 – All rights reserved
1High-pressure decorative laminates — Composite elements — Part 2: Specifications for composite elements with wood-based substrates for interior use 1 Scope This part of ISO 13894 describes the general properties of composite elements surfaced, and possibly edged, with high-pressure decorative laminate (HPDL) as defined in Clause 3. The composite elements specified in this part of ISO 13894 consist of HPDL sheet material adhesively bonded to one or both sides of a wood-based substrate, and are intended for normal interior use. Requirements for special applications, e.g. where the product is subjected to extreme conditions of heat or moisture, are not part of this part of ISO 13894, although Part 1 of this International Standard describes test methods for additional properties which may be applicable to such applications (see ISO 13894-1:2000, Subclause 3.1, Note 3). Test methods and performance levels for special applications shall be agreed between customer and supplier. Information concerning test methods for special applications is given in Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1096, Plywood — Classification ISO 4586-1:2004, High-pressure decorative laminates — Sheets made from thermosetting resins — Part 1: Classification and specifications ISO 13894-1:2000, High-pressure decorative laminates — Composite elements — Part 1: Test methods ISO 17064, Wood-based panels — Fibreboard, particleboard and oriented strand board (OSB) — Vocabulary 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 high-pressure decorative laminate (HPDL) composite element with wood-based substrate composite board produced by adhesively bonding high-pressure decorative laminate (HPDL) sheet material to one or both sides of a wood-based substrate kSIST FprEN ISO 13894-2:2014



ISO 13894-2:2005(E) 2
© ISO 2005 – All rights reserved 3.2 high-pressure decorative laminate(s) HPDL HPL See Definition 3.1 in ISO 4586-1:2004. 3.3 wood-based substrate particleboard, oriented-strand board, fibreboard (ISO 17064) or plywood (ISO 1096) NOTE Solid timber and blockboard are not suitable substrates for HPDL. 3.4 board composite board in the manufacturer's standard sheet size, possibly with one or two sides having postformed edges 3.5 panel composite panel cut to a specified size, with finished edges 4 Requirements All composite elements for normal interior use shall meet the requirements fo
...