SIST EN ISO 19712-3:2022

Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2022)

This document specifies the methods of test for determination of the properties of solid surfacing
materials, as defined in Clause 3, in the form of shaped products. These methods are primarily intended
for testing the materials specified in ISO 19712-1.
The tests can be carried out on finished products, but are generally carried out on test panels of a size
sufficient to meet the requirements of the test, and of the same material and finish as the finished
product.

Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3: Prüfverfahren - Formteile (ISO 19712-3:2022)

Dieses Dokument legt die Prüfverfahren zur Bestimmung der Eigenschaften von Mineralwerkstoffen fest, die wie in Abschnitt 3 definiert geformte Produkte sind. Diese Verfahren sind hauptsächlich zur Prüfung der in ISO 19712 1 festgelegten Werkstoffe vorgesehen.
Die Prüfungen können an fertigen Erzeugnissen durchgeführt werden, werden jedoch im Allgemeinen an Prüfplatten vorgenommen, deren Größe ausreichend ist, um die Prüfanforderungen zu erfüllen, und die aus dem gleichen Material bestehen und die gleiche Oberflächenbeschaffenheit aufweisen wie die fertigen Erzeugnisse.
SICHERHEITSVORKEHRUNGEN — Personen, die dieses Dokument anwenden, sollten gegebenenfalls mit der üblichen Laborpraxis vertraut sein. Dieses Dokument erhebt nicht den Anspruch, alle Sicherheitsprobleme zu behandeln, die gegebenenfalls mit seiner Anwendung verbunden sind. Es liegt in der Verantwortung des Anwenders, geeignete Vorkehrungen für den Arbeits- und Gesundheitsschutz und für die Einhaltung jeglicher gesetzlicher Bestimmungen zu treffen.

Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 3: Détermination des propriétés - Produits mis en forme (ISO 19712-3:2022)

Le présent document spécifie les méthodes d'essai pour la détermination des propriétés des matériaux massifs de revêtement de surface sous forme de produits formés, tels que définis à l'Article 3. Ces méthodes sont principalement destinées à la réalisation des essais sur les matériaux spécifiés dans l'ISO 19712‑1.
Les essais peuvent être effectués sur des produits finis, mais ils sont généralement effectués sur des panneaux d'essai de taille suffisante pour répondre aux exigences de l'essai et réalisés à partir du même matériau et de la même finition que le produit fini.

Polimerni materiali - Dekorativni trdni površinski materiali - 3. del: Ugotavljanje lastnosti - Oblika (ISO 19712-3:2022)

Ta dokument določa preskusne metode za določanje lastnosti trdnih površinskih materialov oz. oblikovanih izdelkov, kot je opredeljeno v točki 3. Te metode so primarno namenjene preskušanju materialov, določenih v standardu ISO 19712-1. Preskuse je mogoče izvajati na končnih izdelkih, vendar se običajno izvajajo na preskusnih ploščah v taki velikosti, da izpolnjujejo zahteve preskusa, ter so iz istega materiala in končne obdelave kot končni izdelek.

General Information

• Status: Published
• Public Enquiry End Date: 31-Jan-2022
• Publication Date: 02-May-2022
• ICS: 83.140.20 - Laminated sheets
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 20-Apr-2022
• Due Date: 25-Jun-2022
• Completion Date: 03-May-2022
• Ref Project: EN ISO 19712-3:2022 - Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2022)

Relations

• Replaces: SIST EN ISO 19712-3:2014 - Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2007)
• Effective Date: 20-Apr-2022
• Replaces: SIST EN ISO 19712-3:2014 - Plastics - Decorative solid surfacing materials - Part 3: Determination of properties - Solid surface shapes (ISO 19712-3:2007)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19712-3:2022
01-junij-2022
Nadomešča:
SIST EN ISO 19712-3:2014
Polimerni materiali - Dekorativni trdni površinski materiali - 3. del: Ugotavljanje
lastnosti - Oblika (ISO 19712-3:2022)
Plastics - Decorative solid surfacing materials - Part 3: Determination of properties -
Solid surface shapes (ISO 19712-3:2022)
Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3: Prüfverfahren - Formteile (ISO 19712
-3:2022)
Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 3:
Détermination des propriétés - Produits mis en forme (ISO 19712-3:2022)
Ta slovenski standard je istoveten z: EN ISO 19712-3:2022
ICS:
83.140.20 Laminatne plošče Laminated sheets
SIST EN ISO 19712-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19712-3:2022

---------------------- Page: 2 ----------------------
SIST EN ISO 19712-3:2022


EN ISO 19712-3
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2022
EUROPÄISCHE NORM
ICS 83.140.20 Supersedes EN ISO 19712-3:2013
English Version

Plastics - Decorative solid surfacing materials - Part 3:
Determination of properties - Solid surface shapes (ISO
19712-3:2022)
Plastiques - Matériaux décoratifs massifs de Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3:
revêtement de surface - Partie 3: Détermination des Prüfverfahren - Formteile (ISO 19712-3:2022)
propriétés - Produits mis en forme (ISO 19712-3:2022)
This European Standard was approved by CEN on 18 March 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19712-3:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 19712-3:2022
EN ISO 19712-3:2022 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 19712-3:2022
EN ISO 19712-3:2022 (E)
European foreword
This document (EN ISO 19712-3:2022) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2022, and conflicting national standards shall
be withdrawn at the latest by October 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19712-3:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19712-3:2022 has been approved by CEN as EN ISO 19712-3:2022 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 19712-3:2022

---------------------- Page: 6 ----------------------
SIST EN ISO 19712-3:2022
INTERNATIONAL ISO
STANDARD 19712-3
Second edition
2022-03
Plastics — Decorative solid surfacing
materials —
Part 3:
Determination of properties — Solid
surface shapes
Plastiques — Matériaux décoratifs massifs de revêtement de
surface —
Partie 3: Détermination des propriétés — Produits mis en forme
Reference number
ISO 19712-3:2022(E)
© ISO 2022

---------------------- Page: 7 ----------------------
SIST EN ISO 19712-3:2022
ISO 19712-3:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 19712-3:2022
ISO 19712-3:2022(E)
Contents Page
Foreword . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Cleaning the test specimen surface .2
4.1 General . 2
4.2 Materials . 2
4.3 Procedure . 2
5 Surface defects . 2
5.1 Procedure . 2
5.2 Method of inspection of surface . 3
5.3 Performance requirements . 3
5.4 Test report . 3
6 Resistance to impact by large-diameter ball . 3
6.1 Principle . 3
6.2 Test specimen . 3
6.3 Procedure . 3
6.4 Performance requirement . 4
6.5 Test report . 4
7 Lightfastness . 5
7.1 Method A . 5
7.1.1 Principle . 5
7.1.2 Apparatus . 5
7.1.3 Test specimen . 5
7.1.4 Procedure . 5
7.1.5 Assessment of specimen and expression of results . 6
7.1.6 Test report . 6
7.2 Method B . 6
7.2.1 Principle . 6
7.2.2 Materials . 7
7.2.3 Apparatus . 7
7.2.4 Standardization of apparatus . 7
7.2.5 Test specimens . 7
7.2.6 Procedure . 7
7.2.7 Expression of results . 8
7.2.8 Test report . 8
7.3 Method C (resistance to colour change in light from an enclosed carbon-arc lamp) . 9
7.3.1 Principle . 9
7.3.2 Apparatus . 9
7.3.3 Test specimen . 9
7.3.4 Procedure . 9
7.3.5 Evaluation and expression of results . 9
7.3.6 Test report . 9
8 Stain/chemical-resistance test .10
8.1 Method A . 10
8.1.1 Principle . 10
8.1.2 Staining agents . 10
8.1.3 Apparatus and materials . 10
8.1.4 Test specimens . 10
8.1.5 Procedures . 14
8.1.6 Expression of results . 14
8.1.7 Test report . 14
iii
© ISO 2022 – All rights reserved

---------------------- Page: 9 ----------------------
SIST EN ISO 19712-3:2022
ISO 19712-3:2022(E)
8.2 Method B . 15
8.2.1 Principle . 15
8.2.2 Materials .15
8.2.3 Apparatus . 16
8.2.4 Test specimen . 16
8.2.5 Procedure . 17
8.2.6 Expression of results . 18
8.2.7 Test report . 19
9 Resistance to cigarette burns .19
9.1 Method A . 19
9.1.1 Principle . 19
9.1.2 Materials . 19
9.1.3 Test specimen . 19
9.1.4 Procedure . 19
9.1.5 Expression of results . 20
9.1.6 Test report .20
9.2 Method B (simulated test using electric heater) . 20
9.2.1 Principle . 20
9.2.2 Apparatus .20
9.2.3 Test specimens . 25
9.2.4 Procedure . 25
9.2.5 Expression of results . 27
9.2.6 Test report . 27
10 Resistance to dry heat .27
10.1 Method A . 27
10.1.1 Principle . 27
10.1.2 Materials . 27
10.1.3 Apparatus .28
10.1.4 Test specimen .28
10.1.5 Procedure .28
10.1.6 Expression of results .28
10.1.7 Test report .28
10.2 Method B .29
10.2.1 Principle . 29
10.2.2 Materials .29
10.2.3 Apparatus . 29
10.2.4 Test specimen .29
10.2.5 Procedure . 30
10.2.6 Expression of results . 31
10.2.7 Test report . 32
10.3 Method C . 32
10.3.1 Test specimen . 32
10.3.2 Procedure . 32
10.3.3 Performance requirements . 32
10.3.4 Test report . 32
11 Resistance to wet heat .33
11.1 Method A . 33
11.1.1 Principle . 33
11.1.2 Materials . 33
11.1.3 Apparatus . 33
11.1.4 Test specimen . 33
11.1.5 Procedure . 33
11.1.6 Expression of results . 33
11.1.7 Test report .34
11.2 Method B .34
11.2.1 Principle .34
11.2.2 Materials .34
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 19712-3:2022
ISO 19712-3:2022(E)
11.2.3 Apparatus .34
11.2.4 Test specimen . 35
11.2.5 Procedure . 35
11.2.6 Expression of results . 35
11.2.7 Test report .36
12 Hot/cold-cycle water-resistance test .36
12.1 Method A — Kitchen sinks . .36
12.1.1 Principle . 36
12.1.2 Apparatus and materials . 36
12.1.3 Test specimen . 37
12.1.4 Procedure .
...

SLOVENSKI STANDARD
oSIST prEN ISO 19712-3:2022
01-januar-2022
Polimerni materiali - Dekorativni trdni površinski materiali - 3. del: Ugotavljanje
lastnosti - Oblika (ISO/FDIS 19712-3:2021)
Plastics - Decorative solid surfacing materials - Part 3: Determination of properties -
Solid surface shapes (ISO/FDIS 19712-3:2021)
Kunststoffe - Dekorative Mineralwerkstoffe - Teil 3: Prüfverfahren - Formteile (ISO/FDIS
19712-3:2021)
Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 3:
Détermination des propriétés - Produits mis en forme (ISO/FDIS 19712-3:2021)
Ta slovenski standard je istoveten z: prEN ISO 19712-3
ICS:
83.140.20 Laminatne plošče Laminated sheets
oSIST prEN ISO 19712-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19712-3:2022

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19712-3:2022
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 19712-3
ISO/TC 61/SC 11
Plastics — Decorative solid surfacing
Secretariat: JISC
materials —
Voting begins on:
2021-11-16
Part 3:
Voting terminates on:
Determination of properties — Solid
2022-02-08
surface shapes
Plastiques — Matériaux décoratifs massifs de revêtement de
surface —
Partie 3: Détermination des propriétés — Produits mis en forme
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 19712-3:2021(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2021

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19712-3:2022
ISO/FDIS 19712-3:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2021 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19712-3:2022
ISO/FDIS 19712-3:2021(E)
Contents Page
Foreword . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Cleaning the test specimen surface .2
4.1 General . 2
4.2 Materials . 2
4.3 Procedure . 2
5 Surface defects . 2
5.1 Procedure . 2
5.2 Method of inspection of surface . 3
5.3 Performance requirements . 3
5.4 Test report . 3
6 Resistance to impact by large-diameter ball . 3
6.1 Principle . 3
6.2 Test specimen . 3
6.3 Procedure . 3
6.4 Performance requirement . 4
6.5 Test report . 4
7 Lightfastness . 5
7.1 Method A . 5
7.1.1 Principle . 5
7.1.2 Apparatus . 5
7.1.3 Test specimen . 5
7.1.4 Procedure . 5
7.1.5 Assessment of specimen and expression of results . 6
7.1.6 Test report . 6
7.2 Method B . 6
7.2.1 Principle . 6
7.2.2 Materials . 7
7.2.3 Apparatus . 7
7.2.4 Standardization of apparatus . 7
7.2.5 Test specimens . 7
7.2.6 Procedure . 7
7.2.7 Expression of results . 8
7.2.8 Test report . 8
7.3 Method C (resistance to colour change in light from an enclosed carbon-arc lamp) . 9
7.3.1 Principle . 9
7.3.2 Apparatus . 9
7.3.3 Test specimen . 9
7.3.4 Procedure . 9
7.3.5 Evaluation and expression of results . 9
7.3.6 Test report . 9
8 Stain/chemical-resistance test .10
8.1 Method A . 10
8.1.1 Principle . 10
8.1.2 Staining agents . 10
8.1.3 Apparatus and materials . 10
8.1.4 Test specimens . 10
8.1.5 Procedures . 14
8.1.6 Expression of results . 14
8.1.7 Test report . 14
iii
© ISO 2021 – All rights reserved

---------------------- Page: 5 ----------------------
oSIST prEN ISO 19712-3:2022
ISO/FDIS 19712-3:2021(E)
8.2 Method B . 15
8.2.1 Principle . 15
8.2.2 Materials . 15
8.2.3 Apparatus . 16
8.2.4 Test specimen . 16
8.2.5 Procedure . 17
8.2.6 Expression of results . 18
8.2.7 Test report . 19
9 Resistance to cigarette burns .19
9.1 Method A . 19
9.1.1 Principle . 19
9.1.2 Materials . 19
9.1.3 Test specimen . 19
9.1.4 Procedure . 19
9.1.5 Expression of results .20
9.1.6 Test report .20
9.2 Method B (simulated test using electric heater) . 20
9.2.1 Principle . 20
9.2.2 Apparatus . 20
9.2.3 Test specimens . 25
9.2.4 Procedure .25
9.2.5 Expression of results . 27
9.2.6 Test report . 27
10 Resistance to dry heat .27
10.1 Method A . 27
10.1.1 Principle . 27
10.1.2 Materials . 27
10.1.3 Apparatus .28
10.1.4 Test specimen .28
10.1.5 Procedure .28
10.1.6 Expression of results .28
10.1.7 Test report .28
10.2 Method B .29
10.2.1 Principle . 29
10.2.2 Materials .29
10.2.3 Apparatus .29
10.2.4 Test specimen .29
10.2.5 Procedure .30
10.2.6 Expression of results . 31
10.2.7 Test report . 32
10.3 Method C . 32
10.3.1 Test specimen . 32
10.3.2 Procedure . 32
10.3.3 Performance requirements . 32
10.3.4 Test report . 32
11 Resistance to wet heat .33
11.1 Method A . 33
11.1.1 Principle . 33
11.1.2 Materials . 33
11.1.3 Apparatus . 33
11.1.4 Test specimen . 33
11.1.5 Procedure . 33
11.1.6 Expression of results .33
11.1.7 Test report .34
11.2 Method B .34
11.2.1 Principle .34
11.2.2 Materials .34
iv
  © ISO 2021 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 19712-3:2022
ISO/FDIS 19712-3:2021(E)
11.2.3 Apparatus .34
11.2.4 Test specimen . 35
11.2.5 Procedure . 35
11.2.6 Expression of results .35
11.2.7 Test report .36
12 Hot/cold-cycle water-resistance test .36
12.1 Method A — Kitchen sinks . .36
12.1.1 Principle . 36
12.1.2 Apparatus and materials . 36
12.1.3 Test specimen . 37
12.1.4 Procedure . 37
12.1.5 Performance requirement .38
12.1.6 Test report .38
12.2 Method B — Other shaped products . 39
12.2.1 Principle . 39
12.2.2 Apparatus and materials . 39
12.2.3 Test specimen . 39
12.2.4 Procedure .39
12.2.5 Performance requirement . 39
12.2.6 Test report .39
13 Hardness .40
14 Ability to be renewed .40
Bibliography .41
v
© ISO 2021 – All rights reserved

---------------------- Page: 7 ----------------------
oSIST prEN ISO 19712-3:2022
ISO/FDIS 19712-3:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, P
...