SIST-TS CEN/TS 14464:2010
(Main)Sawn timber - Method for assessment of case-hardening
Sawn timber - Method for assessment of case-hardening
This Technical Specification defines a destructive method of assessing the case-hardening of a piece of sawn timber with reference to the distortion measured in a slice taken from the piece. This Technical Specification is applicable to sawn timber and timber which has been planed or surfaced by other means. It applies to both hardwood and softwood with a thickness not greater than 100 mm.
Schnittholz - Verfahren zur Ermittlung der Verschalung
Die Technische Spezifikation legt ein zerstörendes Verfahren zur Ermittlung der Verschalung in einem Stück Schnittholz fest, unter Verwendung der an einem Querriegel ermittelten Deformation. Dieses Dokument gilt für Schnittholz und für Holz, welches gehobelt oder anderweitig oberflächenbearbeitet wurde. Es gilt für Laub und Nadelholz mit einer Dicke von nicht über 100 mm.
Bois sciés - Méthode de mesure de la cémentation
Le présent document définit une méthode destructive permettant la mesure de la cémentation d’une pièce de bois scié en référence à la déformation mesurée dans une section extraite de la pièce. Ce document s’applique aux bois sciés et aux bois rabotés ou surfacés par d’autres moyens. Il s’applique à la fois aux bois feuillus et aux bois résineux d’une épaisseur inférieure à 100 mm.
Žagani les - Metoda ocenjevanja zaskorjenosti
Ta tehnična specifikacija določa destruktivno metodo za ocenjevanje zaskorjenosti kosa žaganega lesa glede na ukrivljanje, merjeno na rezini, vzeti s kosa. Ta tehnična specifikacija se uporablja za žagan les in les, ki je bil zglajen ali pooblan na druge načine. Uporablja se tako za trdi les kot mehki les debeline največ 100 mm.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 14464:2010
01-april-2010
Žagani les - Metoda ocenjevanja zaskorjenosti
Sawn timber - Method for assessment of case-hardening
Schnittholz - Verfahren zur Ermittlung der Verschalung
Bois sciés - Méthode de mesure de la cémentation
Ta slovenski standard je istoveten z: FprCEN/TS 14464
ICS:
79.040 Les, hlodovina in žagan les Wood, sawlogs and sawn
timber
kSIST-TS FprCEN/TS 14464:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TS FprCEN/TS 14464:2010
---------------------- Page: 2 ----------------------
kSIST-TS FprCEN/TS 14464:2010
TECHNICAL SPECIFICATION
FINAL DRAFT
FprCEN/TS 14464
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
January 2010
ICS 79.040 Will supersede ENV 14464:2002
English Version
Sawn timber - Method for assessment of case-hardening
Bois sciés - Méthode de mesure de la cémentation Schnittholz - Verfahren zur Ermittlung der Verschalung
This draft Technical Specification is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC
175.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change without notice
and shall not be referred to as a Technical Specification.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 14464:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TS FprCEN/TS 14464:2010
FprCEN/TS 14464:2010 (E)
Contents Page
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Slicing test method .5
4.1 Apparatus .5
4.1.1 Calibrated measuring device .5
4.1.2 Jig .5
4.1.3 Slicing device .5
4.2 Procedure .5
4.3 Calculation and expression of results .7
2
---------------------- Page: 4 ----------------------
kSIST-TS FprCEN/TS 14464:2010
FprCEN/TS 14464:2010 (E)
Foreword
This document (FprCEN/TS 14464:2010) has been prepared by Technical Committee CEN/TC 175 “Round
and sawn timber”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Formal Vote.
This document will supersede ENV 14464:2002.
3
---------------------- Page: 5 ----------------------
kSIST-TS FprCEN/TS 14464:2010
FprCEN/TS 14464:2010 (E)
1 Scope
This Technical Specification defines a destructive method of assessing the case-hardening of a piece of sawn
timber with reference to the distortion measured in a slice taken from the piece.
This document is applicable to sawn timber and timber which has been planed or surfaced by other means. It
applies to both hardwood and softwood with a thickness not greater than 100 mm.
2 Normative refere
...
SLOVENSKI STANDARD
SIST-TS CEN/TS 14464:2010
01-december-2010
1DGRPHãþD
SIST ENV 14464:2003
Žagani les - Metoda ocenjevanja zaskorjenosti
Sawn timber - Method for assessment of case-hardening
Schnittholz - Verfahren zur Ermittlung der Verschalung
Bois sciés - Méthode de mesure de la cémentation
Ta slovenski standard je istoveten z: CEN/TS 14464:2010
ICS:
79.040 Les, hlodovina in žagan les Wood, sawlogs and sawn
timber
SIST-TS CEN/TS 14464:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 14464:2010
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 14464:2010
TECHNICAL SPECIFICATION
CEN/TS 14464
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
July 2010
ICS 79.040 Supersedes ENV 14464:2002
English Version
Sawn timber - Method for assessment of case-hardening
Bois sciés - Méthode de mesure de la cémentation Schnittholz - Verfahren zur Ermittlung der Verschalung
This Technical Specification (CEN/TS) was approved by CEN on 15 May 2010 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14464:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 14464:2010
CEN/TS 14464:2010 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 Slicing test method .5
4.1 Apparatus .5
4.2 Procedure .5
4.3 Calculation and expression of results .7
2
---------------------- Page: 4 ----------------------
SIST-TS CEN/TS 14464:2010
CEN/TS 14464:2010 (E)
Foreword
This document (CEN/TS 14464:2010) has been prepared by Technical Committee CEN/TC 175 “Round and
sawn timber”, the secretariat of which is held by AFNOR.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes ENV 14464:2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST-TS CEN/TS 14464:2010
CEN/TS 14464:2010 (E)
1 Scope
This Technical Specification defines a destruc
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.