SIST EN 60317-56:2012

Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180

This part of IEC 60317 specifies the requirements of solderable fully insulated (FIW) zerodefect enamelled round copper wire, class 180, with a single coating based on polyurethane resin, which may be modified providing it retains its chemical identity and satisfies all the required technical specifications. The range of nominal conductor diameters of the wires covered by this standard is as follows: - Grade of FIW 3 to FIW 08: 0,040 mm up to and including 0,067 mm; - Grade of FIW 3 to FIW 09: 0,071 mm up to and including 0,355 mm; - Grade of FIW 3 to FIW 08: 0,375 mm up to and including 0,475 mm; - Grade of FIW 3 to FIW 07: 0,500 mm up to and including 0,750 mm; - Grade of FIW 3 to FIW 06: 0,800 mm up to and including 1,000 mm; - Grade of FIW 3 to FIW 05: 1,060 mm up to and including 1,600 mm. The nominal conductor diameters are specified in IEC 60317-0-7.

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 56: Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, verzinnbar, lackisoliert mit Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180

Spécifications pour types particuliers de fils de bobinage - Partie 56: Fil brasable de section circulaire, isolé en continu, en cuivre émaillé avec polyuréthane sans défaut d'isolation électrique, avec diamètre nominal de conducteur compris entre 0,040 mm et 1,600 mm, classe 180

La CEI 60317-56:2012 spécifie les exigences d'un fil de bobinage brasable, isolé en continu (FIW: Fully Insulated Wire), sans défaut d'isolation électrique, de section circulaire en cuivre émaillé, de classe 180, avec un revêtement unique à base de résine polyuréthane pouvant être modifiée à condition qu'elle conserve son identité chimique et satisfasse à toutes les spécifications techniques requises. Il convient de noter que la numérotation des articles de la présente spécification n'est pas continue du fait de la suppression d'essais ne faisant plus partie de la série des spécifications CEI 60317-0 relatives aux exigences générales. De plus, un espace réservé est prévu pour de futurs essais des fils de bobinage de manière à conserver une distinction entre les exigences propres aux fils et celles propres à leur conditionnement.   Cette publication doit être lue conjointement avec la CEI 60317-0-7:2012.

Specifikacije za posebne vrste navijalnih žic - 56. del: Spajkljive, popolnoma izolirane in s poliuretanom brezhibno pološčene okrogle bakrove žice z nazivnim premerom prevodnika 0,040 mm do 1,600 mm, razred 180

Ta del standarda IEC 60317 določa zahteve za spajkljivo, popolnoma izolirano (FIW) in brezhibno lakirano okroglo bakreno žico, razreda 180, z enim samim premazom na osnovi poliuretanske smole, ki se lahko spremeni, če ohrani svojo kemijsko identiteto in izpolnjuje vse zahtevane tehnične specifikacije. Razponi nazivnih premerov prevodnikov žic, ki jih zajema ta standard, so: – razred FIW 3 do FIW 08: 0,040 mm do in vključno z 0,067 mm; – razred FIW 3 do FIW 09: 0,071 mm do in vključno z 0,355 mm; – razred FIW 3 do FIW 08: 0,375 mm do in vključno z 0,475 mm; – razred FIW 3 do FIW 07: 0,500 mm do in vključno z 0,750 mm; – razred FIW 3 do FIW 06: 0,800 mm do in vključno z 1,000 mm; – razred FIW 3 do FIW 05: 1,060 mm do in vključno z 1,600 mm. Nazivni premeri prevodnika so navedeni v standardu IEC 60317-0-7.

General Information

• Status: Withdrawn
• Publication Date: 16-Jul-2012
• Withdrawal Date: 20-Sep-2020
• ICS: 29.060.10 - Wires
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 21-Sep-2020
• Due Date: 14-Oct-2020
• Completion Date: 21-Sep-2020
• Ref Project: EN 60317-56:2012 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm, class 180

Relations

• Replaced By: SIST EN 60317-56:2018 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)
• Effective Date: 13-Nov-2017
• Revised: SIST EN 60317-56:2018 - Specifications for particular types of winding wires - Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled round copper wire, class 180 (IEC 60317-56:2017)
• Effective Date: 08-Sep-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60317-56:2012
01-september-2012
6SHFLILNDFLMH]DSRVHEQHYUVWHQDYLMDOQLKåLFGHO6SDMNOMLYHSRSROQRPD
L]ROLUDQHLQVSROLXUHWDQRPEUH]KLEQRSRORãþHQHRNURJOHEDNURYHåLFH]QD]LYQLP
SUHPHURPSUHYRGQLNDPPGRPPUD]UHG
Specifications for particular types of winding wires - Part 56: Solderable fully insulated
(FIW) zero-defect polyurethane enamelled round copper wire with nominal conductor
diameter of 0,040 mm to 1,600 mm, class 180
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 56:
Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer, verzinnbar, lackisoliert mit
Polyurethan, mit Nenndurchmesser von 0,040 mm bis 1,600 mm, Klasse 180
Spécifications pour types particuliers de fils de bobinage - Partie 56: Fil brasable de
section circulaire, isolé en continu, en cuivre émaillé avec polyuréthane sans défaut
d'isolation électrique, avec diamètre nominal de conducteur compris entre 0,040 mm et
1,600 mm, classe 180
Ta slovenski standard je istoveten z: EN 60317-56:2012
ICS:
29.060.10 Žice Wires
SIST EN 60317-56:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60317-56:2012

---------------------- Page: 2 ----------------------

SIST EN 60317-56:2012

EUROPEAN STANDARD
EN 60317-56

NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM

ICS 29.060.10


English version


Specifications for particular types of winding wires -
Part 56: Solderable fully insulated (FIW) zero-defect polyurethane
enamelled round copper wire with nominal conductor diameter
of 0,040 mm to 1,600 mm, class 180
(IEC 60317-56:2012)


Spécifications pour types particuliers  Technische Lieferbedingungen für
de fils de bobinage - bestimmte Typen von Wickeldrähten -
Partie 56: Fil brasable de section Teil 56: Isolationsfehlerfreie Runddrähte
circulaire, isolé en continu, en cuivre (FIW) aus Kupfer, verzinnbar, lackisoliert
émaillé avec polyuréthane sans défaut mit Polyurethan, mit Nenndurchmesser
d'isolation électrique, avec diamètre von 0,040 mm bis 1,600 mm, Klasse 180
nominal de conducteur compris (IEC 60317-56:2012)
entre 0,040 mm et 1,600 mm, classe 180
(CEI 60317-56:2012)



This European Standard was approved by CENELEC on 2012-06-19. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-56:2012 E

---------------------- Page: 3 ----------------------

SIST EN 60317-56:2012
EN 60317-56:2012 - 2 -
Foreword
The text of document 55/1311/FDIS, future edition 1 of IEC 60317-56, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 60317-56:2012.
The following dates are fixed:
(dop) 2013-03-19
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-06-19
• latest date by which the national
standards conflicting with the
document have to be withdrawn

This standard is to be read in conjunction with EN 60317-0-7:2012.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 60317-56:2012 was approved by CENELEC as a European
Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 60317-56:2012
- 3 - EN 60317-56:2012
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year
IEC 60317-0-7 2012 Specifications for particular types EN 60317-0-7 2012
of winding wires -
Part 0-7: General requirements - Fully
insulated (FIW) zero-defect enamelled round
copper wire with nominal conductor diameter
of 0,040 mm to 1,600 mm

---------------------- Page: 5 ----------------------

SIST EN 60317-56:2012

---------------------- Page: 6 ----------------------

SIST EN 60317-56:2012



IEC 60317-56

®


Edition 1.0 2012-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Specifications for particular types of winding wires –

Part 56: Solderable fully insulated (FIW) zero-defect polyurethane enamelled

round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm,


class 180



Spécifications pour types particuliers de fils de bobinage –


Partie 56: Fil brasable de section circulaire, isolé en continu, en cuivre émaillé

avec polyuréthane sans défaut d'isolation électrique, avec diamètre nominal de

conducteur compris entre 0,040 mm et 1,600 mm, classe 180










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX J


ICS 29.060.10 ISBN 978-2-83220-081-0



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60317-56:2012
– 2 – 60317-56  IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions, general notes and appearance . 6
4 Dimensions . 7
5 Electrical resistance . 7
6 Elongation . 7
7 Springiness . 7
8 Flexibility and adherence . 7
9 Heat shock . 7
10 Cut-Through . 7
11 Resistance to abrasion (for nominal diameters of 0,250 mm up to and including
1,000 mm) . 7
12 Resistance to solvents . 8
13 Breakdown voltage . 8
14 Continuity of insulation . 8
15 Temperature index . 8
16 Resistance to refrigerants . 8
17 Solderability . 9
18 Heat or solvent bonding . 9
19 Dielectric dissipation factor . 9
20 Resistance to transformer oil . 9
21 Loss of mass . 9
23 Pin-hole test . 9
30 Packaging . 9

Table 1 – Resistance to abrasion . 8

--------------------
...