Hollow metallic waveguides -- Part 6: Relevant specifications for medium flat rectangular waveguides

Containts a detailed description of mediumflat rectangular waveguides, including mechanical requirements, electrical tests and a table drawn up in inches and millimeters.

Metallische Hohlleiter -- Teil 6: Spezifikationen für mittelflache Rechteckhohlleiter

Guides d'ondes métalliques creux -- Partie 6: Spécifications particulières pour les guides d'ondes rectangulaires plats moyens

Contient une description détaillée des guides d'ondes rectangulaires plats moyens, comprenant les prescriptions mécaniques, les essais électriques, ainsi qu'un tableau de dimensions rédigé en inches et en millimètres.

Hollow metallic waveguides - Part 6: Relevant specifications for medium flat rectangular waveguides

General Information

Status
Published
Publication Date
31-Aug-2002
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Sep-2002
Due Date
01-Sep-2002
Completion Date
01-Sep-2002

Buy Standard

Standardization document
HD 123.6 S2:2002
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI SIST HD 123.6 S2:2002
prva izdaja
STANDARD
september 2002
Hollow metallic waveguides - Part 6: Relevant specifications for medium flat
rectangular waveguides
ICS 33.120.10 Referenčna številka
SIST HD 123.6 S2:2002(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

NORME CEI
INTERNATIONALE IEC
60153-6
INTERNATIONAL
Première édition
STANDARD
First edition
1967-01
Guides d'ondes métalliques creux
Sixième partie:
Spécifications particulières pour les guides
d'ondes rectangulaires plats moyens
Hollow metallic waveguides
Part 6:
Relevant specifications for medium flat
rectangular waveguides
© IEC 1967 Droits de reproduction réservés —
Copyright - all rights reserved
Aucune partie
de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in
utilisée sous quelque forme que ce soit et par aucun any form or by any means, electronic or mechanical,
procédé, électronique ou mécanique, y compris la photo- including photocopying and microfilm, without permission in
copie
et les microfilms, sans l'accord écrit de l'éditeur. writing from the publisher.
International Electrotechnical Commission 3, rue de Varembé Geneva, Switzerland
Telefax: +41 22 919 0300 e-mail: inmail@iec.ch IEC web site http: //www.iec.ch
CODE PRIX
Commission Electrotechnique Internationale
F
PRICE CODE
International Electrotechnical Commission
IEC
Meai4yHapoAHaR 3neKTpoTexHH4ecMaR
KOMHCCHA
Pour prix, voir catalogue en vigueur
• • For price, see current catalogue

---------------------- Page: 2 ----------------------

— 3 —
INTERNATIONAL ELECTROTECHNICAL COMMISSION
HOLLOW METALLIC WAVEGUIDES
Part 6: Relevant specifications for medium flat rectangular waveguides
FOREWORD
1)
The formal decisions or agreements of the IEC on technical matters, prepared by Technical Committees on which all the
National Committees having a special interest therein are represented, express, as nearly as possible, an international
consensus of opinion on the subjects dealt with.
2)
They have the form of recommendations for international use and they are accepted by the National Committees in that
sense.
3) In order to promote this inte
rnational unification, the IEC expresses the wish that all National Committees having as
yet no national rules, when preparing such rules, should use the IEC recommendations as the fundamental basis for these
rules in so far as national conditions will permit.
4)
The desirability is recognized of extending inte rn
ational agreement on these matters through an endeavour to harmonize
national standardization rules with these recommendations in so far as national conditions will permit. The National
Committees pledge their influence towards that end.
PREFACE
This Recommendation was prepared by Sub-Committee 46B, Waveguides and their Accessories,
of IEC Technical Committee No. 46, Cables, Wires, and Waveguides for Telecommunication Equipment.
It contains Part 6: Relevant Specifications for Medium Flat Waveguides, of the complete 1EC Recom-
mendation for Hollow Metallic Waveguides, and it is intended to be used in conjunction with Part 1,
General Requirements and Measuring Methods, which is issued as IEC Publication 153-1.
Relevant specifications for other types of waveguides will appear in companion publications.
The general outline of this Recommendation was first discussed at a meeting held in Ulm in 1959.
A draft was prepared which was considered at the meeting held in Interlaken in 1961. As a result of this
latter meeting, a draft was submitted to the National Committees for approval under the Six Months' Rule
in February 1962.
Several countries submitted comments which were informally considered during the meeting held in
Bucharest in 1962. as the voting period had not yet expired by that time. Based on the comments received,
some amendments were submitted to the National Committees for approval under the Two Months' Pro-
cedure in January 1965. Some comments were discussed and accepted at the meeting held in Baden-Baden
in 1965.
The following countries voted explicitly in favour of publication of Part 6:
Australia
Netherlands
Belgium
Norway
Canada
Poland
Czechoslovakia
Romania
Denmark
Sweden
Finland Switzerland
France
Turkey
Hungary
United Kingdom
India
United States of America
Italy
Yugoslavia
Japan

---------------------- Page: 3 ----------------------

— 5 —
HOLLOW METALLIC WAVEGUIDES
Part 6: Relevant specifications for medium flat rectangular waveguides
MEDIUM FLAT RECTANGULAR WAVEGUIDES — TYPE M
Clause No. of
IEC Publication Item
153-1
1. General
Standardized types
The series of medium flat rectangular waveguides covered by this publication
are shown in Table I.
1.2 Type designation
For these waveguides the type designation comprises:
a) The code: 153 IEC-M
b) A number characterizing a particular size of waveguide. This number
expresses approximately in multiples of 100 MHz (Mc/s) the geometric
mean frequency of the recommended frequency range.
Frequency range
The frequency range indicated in Table I is from 1.25 to 1.9 times the cut-off
frequency in the dominant mode. For any particular type of application, the
working frequency range may be smaller or greater than the frequency range
given in the table.
2. Mechanical requirements
It should be noted that no recommendations are made for the materials to be
used for waveguides. The choice of material must be a greed between customer
and manufacturer.
2.1 Dimensions
2.1.6.1 Inside dimensions
The tolerances both on width and height shalt be approximately:
± 1/1 000
of the inside nominal width.

---------------------- Page: 4 ----------------------

7
Clause No. of
Item
IEC Publication
153-1
2.1.6.1 The nominal values and the tolerances are specified in Table I.
(cont. )
2.1.6.2 Wall thickness
The nominal values are specified in Table I.
Eccentricity
2.1.6.3
The eccentricity shall not exceed 10% of the nominal wall thickness.
2.1.6.4 Outside dimensions
The tolerance both on width and height is approximately: ± 1/500 of the
inside nominal width. The nominal values and tolerances are specified in
Table I.
2.1.6.5 Rectangularity of cross-section
The rectangularity of inside and outside cross-section shall conform to the
requirements specified in Part I of this publication.
2.2 Other mechanical requirements
2.2.1 Bow
The bow shall conform to the requirements specified in Part I of this publi-
cation.
2.2.2 Twist
The twist shall conform to the requirements specified in Part 1 of this publi-
cation.
2.2.3 Surface roughness
Surface roughness shall conform to the requirements specified in Part I of
this publication.
2.2.4 Internal stress
Test procedure and requirements shall conform to Part I of this publication.

---------------------- Page: 5 ----------------------

9
Clause No. of
IEC Publication Item
153-1
3. Electrical tests
3.1 Attenuation
The maximum attenuation shall not exceed 1.3 times the values calculated
from formula (1) in Part I at a frequency of 1.5 times the cut-off frequency.
The values given in the table are for waveguides made of copper with standard
resistivity = 1.7241.10-8 ohm.metre.
po
3.2 Irregularity of characteristic impedance
Irregularity of characteristic impedance shall conform to the requirements
specified in Part I of this publication.
4. Additional tests
4.1 Gas tightness
Gas tightness shall conform to the requirements specified in Part I of this
publication.

---------------------- Page: 6 ----------------------

TABLEAU I - TABLE I
GUIDES D'ONDES RECTANGULAIRES PLATS MOYENS MEDIUM FLAT RECTANGULAR WAVEGUIDES
Bande de fréquences Section droite intérieure Epaisseur Section droite extérieure Affaiblissement en dB/m
Désignation en GHz pour le Inside cross-section nominale Outside cross-section Attenuation in dB/m
de type mode dominant des
parois
r
Largeur Hauteur Tolérance Rayon Largeur Hauteur Tolérance
Fréquence Valeur Valeur
nominale nominale sur largeur et maximal nominale nominale sur largeur Rayon des coins r5
en GHz théorique maximale
+ ±
b hauteur des coins a, h, et hauteur
Type Frequency range a
Radius of corner rz
designation in GHz (Gc/s) for ri
dominant mode Nominal Nominal Tolerance Maximum Nominal Nominal Tolerance
Nominal
width height on width radius width heigth on width
wall-
Frequency in Theoritieal Maximum
a b and height of corner a, h, and height
153 IEC - thickness
De A 1. ,, Minimal Maximal GHz (Gc/s) value value
r, f
From To Minimum Maximum
Dimensions en
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.