SIST EN 13523-24:2005

Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

This Part of EN 13523 describes the procedure for determining the resistance to blocking and/or pressure marking of an organic coating on a metallic substrate.
Pressure generated within a coil or a stack of sheets can affect the coating surface and cause marks of gloss transfer, plasticizer migration, colour change, etc. and even blocking/sticking.
Lighter forms of pressure marking are normally removed by gentle heat (e.g. sunshine).

Bandbeschichtete Metalle - Prüfverfahren - Teil 24: Block- und Stapelfestigkeit

Tôles prélaquées - Méthodes d'essai - Partie 24 : Résistance a l'adhérence et au marbrage

La présente partie de l'EN 13523 décrit le mode opératoire de détermination de la résistance a l'adhérence et/ou au marbrage d'un revetement organique appliqué sur un subjectile métallique.
La pression appliquée sur un rouleau ou une pile de tôles peut affecter la surface du revetement et provoquer des marques de transfert de brillant, la migration de plastifiant, le changement de couleur, etc., voire un phénomene d'adhérence/de collage.
Les formes plus légeres de marbrage sont normalement éliminées par un chauffage modéré (par exemple par exposition au soleil).

Kovine, prevlečene v svitkih - Preskusne metode - 24. del: Odpornost proti zlepljanju in poškodbam zaradi pritiska

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2005
• Withdrawal Date: 06-Nov-2017
• ICS: 25.220.60 - Organic coatings
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 24-Oct-2017
• Due Date: 16-Nov-2017
• Completion Date: 07-Nov-2017
• Ref Project: EN 13523-24:2004 - Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

Relations

• Replaced By: SIST EN 13523-24:2017 - Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking
• Effective Date: 01-Dec-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13523-24:2005
01-april-2005
.RYLQHSUHYOHþHQHYVYLWNLK3UHVNXVQHPHWRGHGHO2GSRUQRVWSURWL
]OHSOMDQMXLQSRãNRGEDP]DUDGLSULWLVND
Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure
marking
Bandbeschichtete Metalle - Prüfverfahren - Teil 24: Block- und Stapelfestigkeit
Tôles prélaquées - Méthodes d'essai - Partie 24 : Résistance a l'adhérence et au
marbrage
Ta slovenski standard je istoveten z: EN 13523-24:2004
ICS:
25.220.60 Organske prevleke Organic coatings
SIST EN 13523-24:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 13523-24:2005

---------------------- Page: 2 ----------------------

SIST EN 13523-24:2005
EUROPEAN STANDARD
EN 13523-24
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2004
ICS 25.220.60
English version
Coil coated metals - Test methods - Part 24: Resistance to
blocking and pressure marking
Tôles prélaquées - Méthodes d'essai - Partie 24 : Bandbeschichtete Metalle - Prüfverfahren - Teil 24: Block-
Résistance à l'adhérence et au marbrage und Stapelfestigkeit
This European Standard was approved by CEN on 23 September 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13523-24:2004: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 13523-24:2005
EN 13523-24:2004 (E)
Foreword
This document (EN 13523-24:2004) has been prepared by Technical Committee CEN/TC 139 “Paints and
varnishes”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by May 2005, and conflicting national standards shall be withdrawn at the latest by
May 2005
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

2

---------------------- Page: 4 ----------------------

SIST EN 13523-24:2005
EN 13523-24:2004 (E)
Introduction
Pressure generated within a coil or a stack of sheets can affect the coating surface and cause marks of gloss
transfer, plasticizer migration, etc. and even blocking/sticking.

3

---------------------- Page: 5 ----------------------

SIST EN 13523-24:2005
EN 13523-24:2004 (E)
1 Scope
This part of EN 13523 describes the procedure for determining the resistance to blocking and/or pressure marking of
an organic coating on a metallic substrate.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references,
only the edition cited applies. For undated references, the latest edition of the referenced document (including any
amendments) applies.
EN 13523-0, Coil coated metals — Test methods — Part 0: General introduction and list of test methods.
EN 13523-4, Coil coated metals — Test methods — Part 4: Pencil hardness.
EN 13523-22, Coil coated metals — Test methods — Part 22: Colour difference — Visual comparison.
EN 23270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and
testing (ISO 3270:1991).
3 Principle
Test panels are placed on top of each other in a stack, the two surfaces to be evaluated being in contact. The stack is
placed in a press, where a uniform pres
...